Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(except LED Headlight)
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291933 LIGHTING SYSTEM(except LED Headlight) J

LIGHTING  LIGHTING SYSTEM(except LED Headlight)  Interior Light Circuit  


DESCRIPTION

The main body ECU receives information regarding the door lock position switch and ignition switch, and turns on each inside handle illumination light.

HINT:

The inside handle illumination lights are the lights which illuminate the drink holders on the front doors and rear slide doors.


WIRING DIAGRAM

B146193E01
0.622,4.047 1.102,4.187 0.480,0.139 10 DOME 1.084,0.657 1.564,0.796 0.480,0.139 10 J8 1.084,0.797 2.753,1.118 1.669,0.321 10 Front Inside Handle Illumination Light LH 3.004,1.615 3.484,1.755 0.480,0.139 10 L4 3.004,1.755 4.673,2.076 1.669,0.321 10 Rear Inside Handle Illumination Light LH 3.004,3.549 3.484,3.688 0.480,0.139 10 K4 3.004,3.689 4.742,4.010 1.738,0.321 10 Rear Inside Handle Illumination Light RH 1.084,2.578 1.564,2.718 0.480,0.139 10 I8 1.056,0.295 1.218,0.434 0.162,0.139 10 1 1.771,0.295 1.933,0.434 0.162,0.139 10 2 1.056,2.214 1.218,2.353 0.162,0.139 10 1 1.771,2.214 1.933,2.353 0.162,0.139 10 2 2.962,1.247 3.124,1.387 0.162,0.139 10 1 3.676,1.247 3.838,1.387 0.162,0.139 10 2 2.962,3.167 3.124,3.306 0.162,0.139 10 1 3.676,3.167 3.838,3.306 0.162,0.139 10 2 1.084,2.719 2.864,3.039 1.780,0.321 10 Front Inside Handle Illumination Light RH 1.388,4.4 2.611,4.539 1.222,0.139 10 from Battery 5.925,3.228 6.964,3.367 1.039,0.139 10 G59 6.202,0.377 6.809,0.516 0.607,0.139 10 FSPT 5.922,0.505 6.102,0.644 0.180,0.139 10 11 5.925,3.36 6.964,3.500 1.039,0.139 10 Main Body ECU

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INTERIOR LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and press the intelligent tester main switch ON.


c.

Select the item below in the Active Test and then check that the light illuminates.

Main body ECU
Item Test Details Diagnostic Note
Step Light Operation Interior light (inside handle illumination light) illumination operation
ON / OFF
-

OK:

Inside handle illumination light illuminates.




NG

2.INSPECT FUSE (DOME)

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT FUSE (DOME)
a.

Remove the DOME fuse from the engine room No. 1 relay block.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

3.INSPECT INSIDE HANDLE ILLUMINATION LIGHT

NG

REPLACE FUSE

3.INSPECT INSIDE HANDLE ILLUMINATION LIGHT
a.
E127508E01
2.423,1.17 3.149,1.347 0.725,0.177 10 Battery (+) 0.043,1.17 0.713,1.347 0.670,0.177 10 Battery (-) 0.92,1.273 1.47,1.273 false 1.812,1.273 2.362,1.273 false

Disconnect the inside handle illumination light connector.


b.

Connect the positive (+) lead from the battery to terminal 1 of the light and the negative (-) lead to terminal 2. Then check that the light illuminates.

OK:

Light illuminates




OK

4.CHECK WIRE HARNESS (BATTERY - MAIN BODY ECU)

NG

REPLACE INSIDE HANDLE ILLUMINATION LIGHT

4.CHECK WIRE HARNESS (BATTERY - MAIN BODY ECU)
a.
U188722E01
0.052,0.017 1.494,0.173 1.442,0.156 10 Wire Harness Side: 1.18,1.796 1.635,1.952 0.455,0.156 10 FSPT 0.697,1.015 0.977,1.196 0.280,0.181 10 G59 1.413,1.44 1.413,1.787 false

Reconnect the inside handle illumination light connector.


b.

Disconnect the G59 ECU connector.


c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
G59-11 (FSPT) - Body ground 10 to 14 V




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR