The AFS ECU operates the headlight swivel motor in accordance with the vehicle speed and steering angle.
The AFS ECU also receives information from the headlight swivel motor.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2412 | When one of following conditions is met:
·
Open or short between AFS ECU and headlight swivel motor LH ·
Abnormal headlight swivel motor LH power supply voltage ·
Headlight swivel motor LH gear faulty |
·
Headlight assembly LH (Headlight swivel motor LH) ·
AFS ECU ·
Wire harness |
| B2413 | When one of following conditions is met:
·
Open or short between AFS ECU and headlight swivel motor RH ·
Abnormal headlight swivel motor RH power supply voltage ·
Headlight swivel motor RH gear faulty |
·
Headlight assembly RH (Headlight swivel motor RH) ·
AFS ECU ·
Wire harness |
Remove the LH ECU-IG fuse from the main body ECU.
Measure the resistance of the fuse.
Below 1 Ω
OK
NG
Disconnect the A28 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A28-14 (IGS) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Tester Connection | Specified Condition |
|---|---|
| A28-22 (E1) - Body ground | Below 1 Ω |
OK
NG
Disconnect the A28 ECU connector.
Disconnect the B2 (for LH) and B17 (for RH) swivel motor connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| A28-1 (SMBL) - B2-3 (SMBL) | Below 1 Ω |
| A28-23 (SMGL) - B2-1 (SBGL) | Below 1 Ω |
| A28-1 (SMBL) or B2-3 (SMBL) - Body ground | 10 kΩ or higher |
| A28-23 (SMGL) or B2-1 (SBGL) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
|---|---|
| A28-2 (SMBR) - B17-3 (SMBR) | Below 1 Ω |
| A28-24 (SMGR) - B17-1 (SBGR) | Below 1 Ω |
| A28-2 (SMBR) or B17-3 (SMBR) - Body ground | 10 kΩ or higher |
| A28-24 (SMGR) or B17-1 (SBGR) - Body ground | 10 kΩ or higher |
OK
NG
Reconnect the A28 ECU connector.
Measure the voltage and resistance of the connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SMBL) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SMBR) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Tester Connection | Specified Condition |
|---|---|
| 23 (SMGL) - Body ground | Below 1 Ω |
| Tester Connection | Specified Condition |
|---|---|
| 24 (SMGR) - Body ground | Below 1 Ω |
OK
NG
Replace the headlight LH or RH with a new one.
Check for DTCs again.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
NEXT
Perform initialization (See page Vehicle Interior>LIGHTING>LIGHTING SYSTEM(except LED Headlight)>INITIALIZATION).
NEXT