CPU IN HID HEADLIGHT
The CPU in the HID headlight executes the fail-safe actions listed below in accordance with the item that has been detected.
| Item | Outline |
|---|---|
| Detection of Abnormal Input Voltage | ·
If voltage that is input to CPU deviates from operating voltage (9 to 16 V), CPU stops illuminating headlights, and resumes illuminating headlights once the voltage reverts to the operating voltage range ·
However, if input voltage decreases after headlights have illuminated, headlights will remain illuminated until the bulbs are extinguished |
| Detection of Abnormal Output (open or short circuit) | If abnormal condition (open or short circuit) occurs in voltage that is output by CPU, CPU stops illuminating headlights and will maintain this state until power is reinstated (by turning headlight dimmer switch from ON or OFF) |
| Detection of Bulb Open | If bulb is not inserted in its socket, CPU stops generating high voltage until bulb is inserted correctly and power is reinstated (by turning headlight dimmer switch from OFF to ON or turning ignition switch from off to on (IG)) |
AFS ECU
If the AFS ECU detects the following malfunctions, it performs a fail-safe operation to blink the AFS OFF indicator in the combination meter.
| Item | Malfunction Detection Condition | Leveling Fail-safe Control | Swivel Fail-safe Control | Fail-safe Deactivation Condition | Warning |
|---|---|---|---|---|---|
| Headlight Swivel Motor | Communication stop | Continues to control with both headlight leveling motors lower than current position by 0.8° | Returns both headlight swivel motors back to front | When normal signal is received | Blinking |
·
Open malfunction ·
Short malfunction ·
Overheat |
·
Returns normally operating headlight swivel motor back to front position ·
Stops malfunctioning swivel motor at current position |
Ignition switch on (IG) again | |||
| Abnormal voltage | When normal value is detected | OFF | |||
| Gear malfunction | Ignition switch on (IG) again | Blinking | |||
| Steering Angle Sensor | Steering angle sensor malfunction | Continues to control | Returns both headlight swivel motors back to front | Ignition switch on (IG) again | Blinking |
| Vehicle Wheel Speed | Vehicle wheel speed signal malfunction | ·
Continues to control using vehicle speed signal of normal side when either side is malfunctioning ·
Determines that vehicle is stopped and continues to control when both sides are malfunctioning |
Returns headlight swivel motor back to forward position after continuing control at vehicle speed before sensor malfunction was detected | When normal signal is received | Blinking |
| Height Control Sensor | Height control sensor malfunction | ·
Returns headlight leveling motor back to initial position if its position is higher than initial position ·
Stops headlight leveling motor at current position if its position is lower than initial position |
Returns both headlight swivel motors back to front | When normal value is detected | Blinking |
| Power source malfunction | Ignition switch on (IG) again | ||||
| Headlight Leveling Motor | Communication stop | ·
Returns headlight leveling motor back to initial position if its position is higher than initial position ·
Stops headlight leveling motor at current position if its position is lower than initial position |
Returns both headlight swivel motors back to front | When normal signal is received | Blinking |
·
Open malfunction ·
Short malfunction ·
Overheat |
·
Headlight leveling motor in malfunctioning side stops at current position ·
Headlight leveling motor in normally functioning side returns back to initial position if its position is higher than initial position, or stops if its position is lower than initial position |
Ignition switch on (IG) again | |||
| Abnormal voltage | When normal value is detected | OFF | |||
| AFS ECU | Rear vehicle height initialization data undetermined | Headlight leveling motor returns back to initial position | Returns both headlight swivel motors back to front | Ignition switch on (IG) again | Continues blinking pattern (Blinks 2 times in one cycle) |
| CAN Communication | Main body ECU communication malfunction
(Headlight information) |
Continues to control | Returns both headlight swivel motors back to front | When normal signal is received | Blinking |
| ECM communication malfunction
(Engine information) |
Continues to control | ||||
| ECM communication malfunction
(Traveling direction information) |
Returns both headlight swivel motors back to front | ||||
| Skid control ECU communication malfunction
(Vehicle speed information) |
Determines that vehicle speed is 0 km/h and continues control | ||||
| Steering angle sensor communication malfunction
(Steering angle information) |
Continues to control | ||||
| Steering angle sensor communication malfunction
(With or without VGRS information) |
|||||
| Improper ECU installation | Improper ECU installation | Continues to control | Continues to control | Ignition switch on (IG) again | Blinking |