Home › Vehicle Interior › LIGHTING › HEADLIGHT ASSEMBLY(except LED Headlight)
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291940 HEADLIGHT ASSEMBLY(except LED Headlight) N

LIGHTING  HEADLIGHT ASSEMBLY(except LED Headlight)  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:

It is possible that a bulb is incorrectly installed, affecting headlight aim. Bulb installation should be considered prior to performing the adjustment procedure.


PROCEDURE

Hide 1. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT

a.

Prepare the vehicle:

·

Ensure there is no damage or deformation to the body around the headlights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are also removed.

·

Sit a person of average weight (55 kg, 121.2 lb) in the driver's seat.

·
E107873

Vehicles with manual headlight beam level control system should be adjusted to "0".



Hide 2. PREPARE FOR HEADLIGHT AIMING

a.
E183359E02
0.792,1.604 1.552,1.917 0.76,0.313 10 false 10 m or 3 m

Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 10 m (32.8 ft.) distance between the vehicle (headlight bulb center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Position the front wheels straight ahead.

·

Bounce the vehicle up and down to settle the suspension.


NOTICE:

A distance of 10 m (32.8 ft.) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of headlight aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)



b.

Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

B140236E07
0.969,0.146 2.698,0.458 1.729,0.313 10 false Alignment distance is 10 m: 4.375,0.146 6.104,0.458 1.729,0.313 10 false Alignment distance is 3 m: 1.146,0.917 1.885,1.115 0.74,0.198 10 false V RH Line 1.146,1.823 1.885,2.021 0.74,0.198 10 false V LH Line 1.25,1.135 1.583,1.365 0.333,0.229 10 false 90° 3.125,1.333 3.646,1.5 0.521,0.167 10 true V Line 4.563,0.917 5.302,1.115 0.74,0.198 10 false V RH Line 4.604,1.792 5.344,1.99 0.74,0.198 10 false V LH Line 4.688,1.156 5.021,1.385 0.333,0.229 10 false 90° 6.542,1.333 7,1.5 0.458,0.167 10 true V Line 4.615,3.615 4.948,3.844 0.333,0.229 10 false 90° 1.198,3.646 1.531,3.875 0.333,0.229 10 false 90° 1.354,4.156 1.708,4.458 0.354,0.302 10 false 10 m 4.875,4.115 5.125,4.438 0.25,0.323 10 false 3 m 3.667,3.479 4.188,3.646 0.521,0.167 10 false H Line 0.25,3.458 0.771,3.625 0.521,0.167 10 false H Line

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
I033423E74
0.26,1.76 0.76,1.917 0.5,0.156 10 false Ground 2.771,0.896 3.219,1.052 0.448,0.156 10 false H Line 1.521,0.125 1.969,0.281 0.448,0.156 10 false V Line 0.594,0.125 1.25,0.281 0.656,0.156 10 false V LH Line 2.125,0.125 2.781,0.281 0.656,0.156 10 false V RH Line

Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

HINT:
·

The base lines differ for "low beam inspection" and "high beam inspection".

·

Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the manufacturer's name marked on the headlight as the center mark.



i.

H line (headlight height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.


ii.

V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):

Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).



Hide 3.INSPECT HEADLIGHT AIMING

a.

Cover the headlight or disconnect the connector of the headlight/headlight ECU on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming inspection.

CAUTION:

Do not disconnect the HID high voltage connector for the bulb when performing this aiming inspection.


NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.


HINT:

When checking the aim of the high beam, cover the low beam or disconnect the connector.



b.

Start the engine.


c.

Turn on the headlights and check if the cutoff line for each low beam matches the preferred cutoff line in the illustration.

E180253E09
1.375,1.698 1.292,1.979 1.292,1.979 1.167,1.979 false 4.885,1.698 4.792,1.979 4.792,1.979 4.667,1.979 false 1.99,1.667 2.24,0.656 2.24,0.656 2.396,0.656 false 5.49,1.667 5.729,0.656 5.729,0.656 5.896,0.656 false 0.656,0.104 2.719,0.469 2.063,0.365 12 false Alignment distance is 10 m: 4.115,0.104 6.177,0.469 2.063,0.365 12 false Alignment distance is 3 m: 1.323,0.521 1.979,0.813 0.656,0.292 10 false V LH Line 0.177,1.313 0.604,1.615 0.427,0.302 10 false H Line 3.865,1.604 4.323,1.917 0.458,0.313 10 false 30 mm 0.344,1.604 0.833,1.917 0.49,0.313 10 false 99 mm 3.115,1.458 3.646,1.771 0.531,0.313 10 false 150 mm 1.354,1.073 1.802,1.385 0.448,0.313 10 false 20 mm 0.469,1.906 1.167,2.552 0.698,0.646 10 false Preferred Cutoff Line 3.979,1.906 4.677,2.552 0.698,0.646 10 false Preferred Cutoff Line 1.448,2.01 1.99,2.323 0.542,0.313 10 false 174 mm 5.542,2.01 6,2.323 0.458,0.313 10 false 52 mm 5.031,2.01 5.49,2.323 0.458,0.313 10 false 52 mm 2.031,2.01 2.604,2.323 0.573,0.313 10 false 174 mm 3.677,1.292 4.104,1.594 0.427,0.302 10 false H Line 6.604,1.458 7.052,1.771 0.448,0.313 10 false 45 mm 4.844,1.073 5.229,1.385 0.385,0.313 10 false 6 mm 2.427,0.583 2.896,0.896 0.469,0.313 10 false Point A 5.927,0.583 6.396,0.896 0.469,0.313 10 false Point A 1.323,0.802 1.979,1.115 0.656,0.313 10 false V RH Line 4.823,0.552 5.479,0.844 0.656,0.292 10 false V LH Line 4.823,0.833 5.479,1.146 0.656,0.313 10 false V RH Line 0.281,2.885 3.906,3.24 3.625,0.354 10 false The illustration shown is for an LHD vehicle. RHD vehicles will project a headlight pattern that is a mirror image.

HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

If the alignment distance is 10 m (32.8 ft.):

The low beam cutoff line should be within 20 mm (0.756 in.) and 150 mm (5.90 in.) below the H line as well as 174 mm (6.87 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The low beam cutoff line should be within 6 mm (0.227 in.) and 45 mm (1.77 in.) below the H line as well as 52 mm (2.06 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 10 m (32.8 ft.):

The horizontal line of the preferred low beam cutoff line is 99 mm (3.92 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.




d.

Turn on the high beams and check if the center of intensity for each high beam matches the preferred center of the intensity in the illustration.

E169333E17
1.99,1.646 2.26,0.635 2.26,0.635 2.406,0.635 false 5.479,1.635 5.76,0.625 5.76,0.625 5.896,0.625 false 0.625,0.115 2.688,0.479 2.063,0.365 12 false Alignment distance is 10 m: 4.083,0.115 6.146,0.479 2.063,0.365 12 false Alignment distance is 3 m: 1.323,0.719 1.979,1.031 0.656,0.313 10 false V LH Line 0.521,1.542 0.948,1.844 0.427,0.302 10 false H Line 1.469,2.146 1.938,2.458 0.469,0.313 10 false 99 mm 2.063,2.156 2.531,2.469 0.469,0.313 10 false 99 mm 4.021,1.51 4.448,1.813 0.427,0.302 10 false H Line 4.969,2.146 5.417,2.458 0.448,0.313 10 false 29 mm 5.573,2.146 6.021,2.458 0.448,0.313 10 false 29 mm 2.688,1.896 3.167,2.208 0.479,0.313 10 false 99 mm 2.677,1.313 3.156,1.625 0.479,0.313 10 false 69 mm 6.177,1.823 6.625,2.135 0.448,0.313 10 false 29 mm 6.177,1.313 6.625,1.625 0.448,0.313 10 false 20 mm 0.917,1.823 1.365,2.135 0.448,0.313 10 false 35 mm 4.458,1.833 4.906,2.146 0.448,0.313 10 false 10 mm 2.427,0.563 3.052,1.208 0.625,0.646 10 false Center of Intensity 5.917,0.552 6.563,1.198 0.646,0.646 10 false Center of Intensity 1.323,1.042 1.979,1.406 0.656,0.365 10 false V RH Line 4.823,0.688 5.479,1 0.656,0.313 10 false V LH Line 4.823,1.042 5.479,1.406 0.656,0.365 10 false V RH Line

HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

If the alignment distance is 10 m (32.8 ft.):

The high beam center of intensity should be within 69 mm (2.74 in.) above and 99 mm (3.91 in.) below the H line as well as 99 mm (3.91 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity should be within 20 mm (0.824 in.) above and 29 mm (1.17 in.) below the H line as well as 29 mm (1.17 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 10 m (32.8 ft.):

The preferred center of the hot zone for high beam is 35 mm (1.37 in.) below the H line and is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The preferred center of the hot zone for high beam is 10 mm (0.412 in.) below the H line and is on the V LH or V RH line.




Hide 4.ADJUST HEADLIGHT AIMING

a.

Adjust the low beam (w/o AFS):

i.
E183365E04
1.625,2.198 1.625,2.823 true 1.135,2.802 2.135,3.115 1,0.313 10 false Aiming Screw A

Adjust the aim vertically:

Adjust the aim of each headlight to the specified range by turning each aiming screw A with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

If it is not possible to correctly adjust headlight aim, check bulb, headlight unit and headlight unit reflector installation.

·

The headlight aim moves down when turning the aiming screw clockwise, and moves up when turning the aiming screw counterclockwise.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.




ii.
E183366E04
0.583,1.635 0.583,2.688 true 0.146,2.698 1.156,3.01 1.01,0.313 10 false Aiming Screw B

Adjust the aim horizontally:

Adjust the aim of each headlight to the specified range by turning each aiming screw B with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

If it is not possible to correctly adjust headlight aim, check bulb, headlight unit and headlight unit reflector installation.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.





b.

Adjust the low beam (w/ AFS):

i.
E183367E02
1.583,1.771 1.583,2.906 true 1.094,2.938 2.104,3.25 1.01,0.313 10 false Aiming Screw A

Adjust the aim vertically:

Adjust the aim of each headlight to the specified range by turning each aiming screw A with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

When adjusting the vertical axis of the headlight, the horizontal axis will also change. It is necessary to adjust the vertical position first, and then correct the horizontal position.

·

If it is not possible to correctly adjust headlight aim, check bulb, headlight unit and headlight unit reflector installation.

·

The headlight aim for the LH side moves up and to the right when turning the aiming screw clockwise, and moves down and to the left when turning the aiming screw counterclockwise.

·

The headlight aim for the RH side moves up and to the left when turning the aiming screw clockwise, and moves down and to the right when turning the aiming screw counterclockwise.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.




ii.
E183368E02
0.656,1.771 0.656,2.833 true 0.188,2.823 1.198,3.135 1.01,0.313 10 false Aiming Screw B

Adjust the aim horizontally:

Adjust the aim of each headlight to the specified range by turning each aiming screw B with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

If it is not possible to correctly adjust headlight aim, check bulb, headlight unit and headlight unit reflector installation.





c.

Adjust the high beam:

i.
E183370E04
2.323,1.833 2.146,0.552 2.146,0.552 1.833,0.552 true 0.552,0.469 1.573,0.792 1.021,0.323 10 false Aiming Screw A

Adjust the aim vertically:

Adjust the aim of each headlight to the specified range by turning each aiming screw A with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

The headlight aim moves up when turning the aiming screw clockwise, and moves down when turning the aiming screw counterclockwise.

·

If it is not possible to correctly adjust headlight aim, check bulb, headlight unit and headlight unit reflector installation.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.




ii.
E183369E04
1.906,2.552 2.104,2.719 2.104,2.719 2.104,2.875 true 1.615,2.938 2.625,3.24 1.01,0.302 10 false Aiming Screw B

Adjust the aim horizontally:

Adjust the aim of each headlight to the specified range by turning each aiming screw B with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

If it is not possible to correctly adjust headlight aim, check bulb, headlight unit and headlight unit reflector installation.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.