Home › Vehicle Interior › LIGHTING › FOG LIGHT ASSEMBLY
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291941 FOG LIGHT ASSEMBLY N

LIGHTING  FOG LIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:

It is possible that a bulb is incorrectly installed, affecting fog light aim. Bulb installation should be considered prior to performing the adjustment procedure.


PROCEDURE

Hide 1. PREPARE VEHICLE FOR FOG LIGHT AIM ADJUSTMENT

a.

Prepare the vehicle:

·

Ensure there is no damage or deformation to the body around the fog lights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are also removed.

·

Sit a person of average weight (55 kg, 121.2 lb) in the driver's seat.



Hide 2. PREPARE FOR FOG LIGHT AIMING

a.

Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it can not.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 10 m (32.8 ft.) distance between the vehicle (fog light bulb center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Position the front wheels straight ahead.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 10 m (32.8 ft.) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of fog light aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)




b.

Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

B140235E05
1.01,0.198 2.74,0.5 1.729,0.302 10 false Alignment distance is 10 m: 4.615,0.198 6.26,0.5 1.646,0.302 10 false Alignment distance is 3 m: 1.01,0.708 1.667,1.021 0.656,0.313 10 false V RH Line 1.031,1.729 1.656,2.042 0.625,0.313 10 false V LH Line 4.458,0.75 5.115,1.063 0.656,0.313 10 false V RH Line 4.469,1.708 5.094,2.021 0.625,0.313 10 false V LH Line 1.208,1.167 1.542,1.396 0.333,0.229 10 false 90° 3.052,1.333 3.573,1.5 0.521,0.167 10 true V Line 4.635,1.167 4.969,1.396 0.333,0.229 10 false 90° 6.49,1.333 7.01,1.5 0.521,0.167 10 true V Line 4.635,3.458 4.948,3.771 0.313,0.313 10 false 90° 1.208,3.271 1.521,3.583 0.313,0.313 10 false 90° 1.354,4.125 1.708,4.427 0.354,0.302 10 false 10 m 4.844,4.104 5.094,4.427 0.25,0.323 10 false 3 m 3.698,3.667 4.219,3.833 0.521,0.167 10 false H Line 0.24,3.698 0.76,3.865 0.521,0.167 10 false H Line

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
I033423E74
0.26,1.76 0.76,1.917 0.5,0.156 10 false Ground 2.771,0.896 3.219,1.052 0.448,0.156 10 false H Line 1.521,0.125 1.969,0.281 0.448,0.156 10 false V Line 0.594,0.125 1.25,0.281 0.656,0.156 10 false V LH Line 2.125,0.125 2.781,0.281 0.656,0.156 10 false V RH Line

Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

HINT:

Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


i.

H Line (Fog light height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.


ii.

V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):

Draw two vertical lines so that they intersect the H line at each center mark aligned with the center of the fog light bulbs).



Hide 3.INSPECT FOG LIGHT AIMING

a.

Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

NOTICE:

Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.



b.

Start the engine.


c.

Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration.

E351340E07
2.094,2.365 2,1.885 true 2.094,2.365 2.354,2.365 false 5.469,2.396 5.344,1.906 true 5.479,2.396 5.74,2.396 false 0.896,0.083 3.063,0.448 2.167,0.365 12 false Alignment distance is 10 m: 4.281,0.073 6.323,0.396 2.042,0.323 12 false Alignment distance is 3 m: 1.552,0.573 2.26,0.875 0.708,0.302 10 false V LH Line 1.542,0.906 2.281,1.135 0.74,0.229 10 false V RH Line 4.927,0.583 5.583,0.823 0.656,0.24 10 false V LH Line 4.927,0.906 5.583,1.188 0.656,0.281 10 false V RH Line 6.083,1.927 6.604,2.198 0.521,0.271 10 false 52 mm 2.708,1.906 3.292,2.219 0.583,0.313 10 false 175 mm 0.302,1.469 0.781,1.75 0.479,0.281 10 false H Line 3.635,1.469 4.063,1.74 0.427,0.271 10 false H Line 2.385,2.281 3,2.552 0.615,0.271 10 false Hot Zone 5.771,2.313 6.417,2.583 0.646,0.271 10 false Hot Zone

HINT:
·

If the alignment distance is 10 m (32.8 ft.):

The upper edge of the hot zone for the fog light should be 175 mm (6.87 in.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The upper edge of the hot zone for the fog light should be 52 mm (2.06 in.) below the H line.




Hide 4.ADJUST FOG LIGHT AIMING

a.
E183333E01
2.559,2.117 3.009,2.788 0.450,0.671 10 Aiming Screw 1.916,2.619 2.249,2.209 2.249,2.209 2.544,2.209 false

Adjust the aim vertically:

Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:

If it is not possible to correctly adjust fog light aim, check bulb, fog light unit and fog light unit reflector installation.