Home › Vehicle Interior › LIGHTING › HEADLIGHT ASSEMBLY(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291964 HEADLIGHT ASSEMBLY(for LED Headlight) G

LIGHTING  HEADLIGHT ASSEMBLY(for LED Headlight)  INSPECTION  


PROCEDURE

Hide 81125 1.INSPECT HEADLIGHT CORD

a.

Measure the resistance according to the value(s) in the table below.

U189995E02
1.594,1.573 2.125,2.031 0.531,0.458 10 false *a 1.604,2.531 2.135,2.99 0.531,0.458 10 false *b 4.938,0.135 5.469,0.594 0.531,0.458 10 false *c 4.5,1.729 5.031,2.188 0.531,0.458 10 false *d 4.583,3.156 5.115,3.615 0.531,0.458 10 false *e 0.354,0.219 0.885,0.677 0.531,0.458 10 false *1 0.49,4.25 1.021,4.708 0.531,0.458 10 false *a 2.208,4.271 2.74,4.729 0.531,0.458 10 false *b 3.875,4.292 4.406,4.75 0.531,0.458 10 false *c 5.635,4.302 6.167,4.76 0.531,0.458 10 false *d 0.885,4.167 1.417,4.625 0.531,0.458 10 false A 2.594,4.167 3.125,4.625 0.531,0.458 10 false B 4.271,4.188 4.802,4.646 0.531,0.458 10 false C 6.042,4.188 6.573,4.646 0.531,0.458 10 false D

Text in Illustration
*1 Headlight Cord - -
*a Component without harness connected
(to Wire Harness)
*b Component without harness connected
(to Wire Harness)
*c Component without harness connected
(to Headlight Leveling Motor)
*d Component without harness connected
(to Headlight Unit Assembly)
*e Component without turn signal light installed
(to Turn Signal Light)
- -

i.

Inspect the headlight leveling motor circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - C-1 Always Below 1 Ω
A-7 - C-3 Always Below 1 Ω
A-8 - C-2 Always Below 1 Ω


If the result is not as specified, replace the headlight cord.


ii.

Inspect the Lo / Hi beam headlight light source circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - D-1 Always Below 1 Ω
A-3 - D-7 Always Below 1 Ω
A-5 - D-5 Always Below 1 Ω


If the result is not as specified, replace the headlight cord.


iii.

Inspect the Lo / Hi beam shade circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - D-2 Always Below 1 Ω
A-6 - D-6 Always Below 1 Ω


If the result is not as specified, replace the headlight cord.


iv.

Inspect the clearance light circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - D-4 Always Below 1 Ω
B-4 - D-8 Always Below 1 Ω


If the result is not as specified, replace the headlight cord.



Hide 81135 2.INSPECT HEADLIGHT UNIT ASSEMBLY

a.
E349546E02
0.25,0.26 0.688,0.698 0.438,0.438 10 false *a

Apply battery voltage to the headlight unit assembly and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 8
Clearance light comes on


Text in Illustration
*a Component without harness connected
(to Headlight Unit Assembly)

If the result is not as specified, replace the headlight unit assembly.


b.

Apply battery voltage to the headlight unit assembly and check that the Lo / Hi beam shade operates.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 6
Operates normally


If the result is not as specified, replace the headlight unit assembly.