Home › Vehicle Interior › LIGHTING › HEADLIGHT ASSEMBLY(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291964 HEADLIGHT ASSEMBLY(for LED Headlight) A

LIGHTING  HEADLIGHT ASSEMBLY(for LED Headlight)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81112B 1.REMOVE COVER RING

a.
E348341

Turn the cover ring as shown in the illustration to remove it.


Hide 81510C 2.REMOVE FRONT TURN SIGNAL LIGHT BULB

a.
E348343

Turn the headlight cord with the front turn signal light bulb as shown in the illustration to disconnect them as a unit.


b.

Remove the front turn signal light bulb from the headlight cord.


Hide 81125 3.REMOVE HEADLIGHT CORD

a.
E348360

Disconnect the 2 connectors.


b.

Disengage the 2 claws and 3 clamps to remove the headlight cord.


Hide 85662 4.REMOVE HEADLIGHT LEVELING MOTOR

a.
E348354E02
1.375,1.417 0.646,1.417 false 2.406,1.896 2.563,2.042 0.156,0.146 10 false 2 1.906,1.083 2.063,1.229 0.156,0.146 10 true 1 0.427,1.323 0.583,1.469 0.156,0.146 10 false *a

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (1) shown in the illustration.

Text in Illustration
*a Aiming Screw

HINT:
·

Turn the aiming screw until the headlight leveling motor can be moved in the direction indicated by the arrow (2) shown in the illustration.

·

Make sure to remember the number of aiming screw rotations.




b.

Turn the headlight leveling motor in the direction indicated by the arrow (2) shown in the illustration to disengage the pin.

HINT:

When removing the headlight leveling motor of the headlight assembly RH, turn the headlight leveling motor in the opposite direction of the arrow (2) shown in the illustration.



c.
E348355E02
1.375,1.417 0.646,1.417 false 1.052,1.833 1.208,1.979 0.156,0.146 10 false 4 1.906,1.083 2.063,1.229 0.156,0.146 10 true 3 0.427,1.323 0.583,1.469 0.156,0.146 10 false *a

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (3) shown in the illustration to disengage the shaft.

Text in Illustration
*a Aiming Screw

HINT:

Make sure to remember the number of aiming screw rotations.



d.

Pull out the headlight leveling motor in the direction indicated by the arrow (4) shown in the illustration to remove it.


Hide 85669 5.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING

a.

Remove the headlight leveling motor base packing.

NOTICE:

After the headlight leveling motor base packing is removed, be sure to replace it with a new one. Failure to do so may cause water ingress.



Hide 81171B 6.REMOVE HEADLIGHT LENS

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.



a.
E348345E02
3.219,0.406 3.375,0.552 0.156,0.146 10 false *b 0.469,0.135 0.625,0.281 0.156,0.146 10 false *a 0.083,1.333 0.24,1.479 0.156,0.146 10 false *a 0.417,1.656 0.573,1.802 0.156,0.146 10 false *a 1.229,1.958 1.385,2.104 0.156,0.146 10 false *a 2.354,1.698 2.51,1.844 0.156,0.146 10 false *a 1.104,0.323 1.26,0.469 0.156,0.146 10 false *a 1.99,0.469 2.146,0.615 0.156,0.146 10 false *a 2.688,0.469 2.844,0.615 0.156,0.146 10 false *a

Remove the 8 screws.

Text in Illustration
*a Screw
*b "TORX" screw


b.

Using a T20H "TORX" driver, remove the "TORX" screw.


c.
E348346

Using a dryer, heat the backside of the headlight assembly.

NOTICE:

If the headlight assembly is heated unevenly, it will deform or melt.



d.
E348347

Disengage the 9 claws.


e.

Separate the headlight lens.

HINT:

If the headlight lens cannot be separate even after heating, using a screwdriver with its tip wrapped with protective tape, lift the headlight lens. Be careful not to damage the headlight lens and housing.



f.
E348348

Disconnect the connector to remove the headlight lens.


Hide 81132B 7.REMOVE HEADLIGHT LENS GASKET

a.
E348349

Remove the headlight lens gasket.

NOTICE:

Make sure to replace the headlight lens gasket with a new one. Failure to do so may cause water ingress.



Hide 81171A 8.REMOVE HEADLIGHT UNIT

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.



a.
E348352

Disconnect the connector.


b.
E348350

While holding the headlight unit by hand, turn the aiming screw as shown in the illustration until the aiming screw is disconnected from the headlight unit.

HINT:

Make sure to remember the number of aiming screw rotations.



c.
E348353

Disengage the 2 claws to remove the headlight unit.