Home › Vehicle Interior › LIGHTING › HEADLIGHT ASSEMBLY(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291964 HEADLIGHT ASSEMBLY(for LED Headlight) A

LIGHTING  HEADLIGHT ASSEMBLY(for LED Headlight)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81171A 1.INSTALL HEADLIGHT UNIT

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.



a.
E348353

Engage the 2 claws to temporarily install the headlight unit.


b.
E348351

While holding the headlight unit by hand, turn the aiming screw as shown in the illustration to install the headlight unit.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



c.
E348352

Connect the connector.


Hide 81132B 2.INSTALL HEADLIGHT LENS GASKET

a.

Completely remove the old headlight lens gasket.


b.
E348349E02
1.125,1.51 1.125,1.865 false 1.052,1.885 1.208,2.031 0.156,0.146 10 false *a

Clean the installation groove of the headlight lens.

Text in Illustration
*a Cleaning Area


c.
E237693E10
1.375,1.083 1.375,1.333 true 0.708,0.948 0.698,1.24 true 1.5,0.458 1.698,0.646 0.198,0.188 10 false 1 0.177,0.635 0.375,0.823 0.198,0.188 10 false 2 1.292,1.365 1.438,1.521 0.146,0.156 10 false *a 0.635,1.271 0.781,1.427 0.146,0.156 10 false *b 1.469,1.896 1.729,2.063 0.26,0.167 10 false *c

Partially remove the release paper from a new headlight lens gasket and cut off a piece of it.

Text in Illustration
*a Release Paper
*b Tape
*c 45°


d.

Fold the release paper over the tip of a screwdriver and secure it in place with tape as indicated by the arrows, in the order shown in the illustration.


e.

Using scissors, cut the end of the headlight lens gasket at a 45° angle.


f.
E348361E02
1.75,2.792 1.75,3.167 false 1.656,3.177 1.813,3.323 0.156,0.146 10 false *a

Starting from the position shown in the illustration and moving counterclockwise, temporarily install the headlight lens gasket as shown in the illustration.

Text in Illustration
*a Starting Position

NOTICE:

Gently install the headlight lens gasket without pulling it.



g.
E348362E02
2.469,1.49 2.625,1.635 0.156,0.146 10 false *a 2.281,1.948 2.438,2.094 0.156,0.146 10 false *a

Set the headlight lens gasket into the corner groove.

Text in Illustration
*a Corner Groove

NOTICE:
·

Gently install the headlight lens gasket without pulling it.

·

If the headlight lens gasket is pulled while it is installed, it will not be installed properly in the corner grooves.




h.
E348363E02
1.531,0.542 1.646,0.75 false 1.625,0.771 1.781,0.917 0.156,0.146 10 false *b 1.104,0.177 1.26,0.323 0.156,0.146 10 false *a

Using 2 screwdrivers with their tips wrapped with release paper, completely press the headlight lens gasket into the groove to install it.

Text in Illustration
*a Press in this Direction
*b Release Paper

NOTICE:
·

Gently install the headlight lens gasket without pulling it.

·

If the headlight lens gasket is pulled while it is installed, it will not be installed properly in the corner grooves.




i.
E348364E02
0.688,2.927 0.865,3.073 0.177,0.146 10 false A 2.531,1.99 2.688,2.135 0.156,0.146 10 false *a 2.615,1.583 2.771,1.729 0.156,0.146 10 false *a 2.927,0.365 3.083,0.51 0.156,0.146 10 false *a 0.552,0.844 0.708,0.99 0.156,0.146 10 false *a 0.271,1.708 0.427,1.854 0.156,0.146 10 false *a

Repeat the following until the headlight lens gasket reaches the starting position: Temporarily install the headlight lens gasket to the straight groove and completely press it into the groove, and then temporarily install it to the corner groove and completely press it into the groove.

Text in Illustration
*a Corner Groove
A 10 mm (0.394 in.) or more

NOTICE:
·

Make sure the headlight lens gasket is not protruding and is installed properly.

·

Make sure there is no gap between the ends of the headlight lens gasket.

·

Make sure to thoroughly check the corners as the headlight lens gasket is likely to be improperly installed in the corners.




Hide 81171B 3.INSTALL HEADLIGHT LENS

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.



a.

Clean the sealing surface of the headlight lens.


b.
E348348

Connect the connector.


c.
E348347

Engage the 9 claws to install the headlight lens to the housing.

NOTICE:

Make sure all of the claws are engaged.



d.
E348345E02
3.219,0.406 3.375,0.552 0.156,0.146 10 false *b 0.469,0.135 0.625,0.281 0.156,0.146 10 false *a 0.083,1.333 0.24,1.479 0.156,0.146 10 false *a 0.417,1.656 0.573,1.802 0.156,0.146 10 false *a 1.229,1.958 1.385,2.104 0.156,0.146 10 false *a 2.354,1.698 2.51,1.844 0.156,0.146 10 false *a 1.104,0.323 1.26,0.469 0.156,0.146 10 false *a 1.99,0.469 2.146,0.615 0.156,0.146 10 false *a 2.688,0.469 2.844,0.615 0.156,0.146 10 false *a

Install the 8 screws.

Text in Illustration
*a Screw
*b "TORX" screw


e.

Using a T20H "TORX" driver, install the "TORX" screw.


f.

Check the installation condition of the headlight lens gasket.

NOTICE:

Make sure the headlight lens gasket is not protruding and completely contacts the headlight lens.



Hide 85669 4.INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING

a.

Install a new headlight leveling motor base packing.


Hide 85662 5.INSTALL HEADLIGHT LEVELING MOTOR

a.
E348356E02
1.375,1.417 0.854,1.417 false 1.906,1.25 2.063,1.396 0.156,0.146 10 true 2 1.188,1.802 1.344,1.948 0.156,0.146 10 false 1 0.635,1.302 0.792,1.448 0.156,0.146 10 false *a

Insert the headlight leveling motor in the direction indicated by the arrow (1) shown in the illustration.

Text in Illustration
*a Aiming Screw


b.

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (2) shown in the illustration to engage the shaft.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



c.
E348357E02
1.375,1.417 0.854,1.417 false 1.906,1.25 2.063,1.396 0.156,0.146 10 true 4 2.427,1.885 2.583,2.031 0.156,0.146 10 false 3 0.635,1.302 0.792,1.448 0.156,0.146 10 false *a

Turn the headlight leveling motor in the direction indicated by the arrow (3) shown in the illustration and engage the pin to install the headlight leveling motor to the headlight assembly.

Text in Illustration
*a Aiming Screw

HINT:

When installing the headlight leveling motor of the headlight assembly RH, turn the headlight leveling motor in the opposite direction of the arrow (3) shown in the illustration.



d.

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (4) shown in the illustration.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



Hide 81125 6.INSTALL HEADLIGHT CORD

a.
E348360

Engage the 2 claws and 3 clamps to install the headlight cord to the housing.


b.

Connect the 2 connectors.


Hide 81510C 7.INSTALL FRONT TURN SIGNAL LIGHT BULB

a.

Install the front turn signal light bulb to the headlight cord.


b.
E348344

Turn the headlight cord with the front turn signal light bulb as shown in the illustration to install them as a unit.


Hide 81112B 8.INSTALL COVER RING

a.
E348342

Turn the cover ring as shown in the illustration to install it.