Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291968 LIGHTING SYSTEM(for LED Headlight) C

LIGHTING  LIGHTING SYSTEM(for LED Headlight)  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects the ambient light. The sensor creates an electrical signal based on the amount of light, and sends the signal to the main body ECU. The main body ECU turns on or off the headlights and taillights according to the signal.

DTC No. DTC Detecting Condition Trouble Area
B1244

Either of the following conditions is met:


·

Malfunction in automatic light control sensor

·

Open or short in automatic light control sensor circuit


·

Automatic light control sensor

·

Harness or connector

·

Main body ECU



WIRING DIAGRAM

E223761E57
0.583,2.635 1.01,2.823 0.427,0.188 10 false H1 0.583,2.813 2.583,3 2,0.188 10 false Automatic Light Control Sensor 4.938,2.833 6.24,3.073 1.302,0.24 10 false Main Body ECU 4.927,2.667 5.198,2.833 0.271,0.167 10 false G58 1.625,0.844 2.042,1.052 0.417,0.208 10 false CLTB 1.625,2.167 2.146,2.427 0.521,0.26 10 false CLTS 1.625,1.51 2.146,1.781 0.521,0.271 10 false CLTE 2.073,2.073 2.344,2.271 0.271,0.198 10 false 5 2.073,1.417 2.333,1.615 0.26,0.198 10 false 3 5.031,0.854 5.427,1.01 0.396,0.156 10 false CLTB 5.031,1.51 5.427,1.667 0.396,0.156 10 false CLTE 5.031,2.167 5.427,2.323 0.396,0.156 10 false CLTS 4.75,0.729 4.938,0.875 0.188,0.146 10 false 20 4.76,1.406 5,1.656 0.24,0.25 10 false 18 4.75,2.063 4.99,2.25 0.24,0.188 10 false 19 2.063,0.75 2.323,0.948 0.26,0.198 10 false 6

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Illumination Rate info Illumination rate information/0.00 ms to 2162.65 ms Value is output according to ambient light levels -

OK:

Normal condition listed above is displayed.




OK

REPLACE MAIN BODY ECU

NG

2.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU)
2.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU)
a.

Disconnect the H1 automatic light control sensor connector.


b.

Disconnect the G58 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H1-3 (CLTE) - G58-18 (CLTE) Always Below 1 Ω
H1-5 (CLTS) - G58-19 (CLTS) Always Below 1 Ω
H1-6 (CLTB) - G58-20 (CLTB) Always Below 1 Ω
H1-3 (CLTE) or G58-18 (CLTE) - Body ground Always 10 kΩ or higher
H1-5 (CLTS) or G58-19 (CLTS) - Body ground Always 10 kΩ or higher
H1-6 (CLTB) or G58-20 (CLTB) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAIN BODY ECU
a.
U189993E02
1.094,1.875 0.625,2.458 false 1.365,1.885 1.167,2.521 false 0.25,0.156 0.49,0.365 0.24,0.208 10 false *a 1.583,0.552 1.969,0.76 0.385,0.208 10 false G58 0.354,2.49 0.792,2.667 0.438,0.177 10 false CLTB 0.958,2.563 1.354,2.74 0.396,0.177 10 false CLTE

Reconnect the G58 main body ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G58-20 (CLTB) - G58-18 (CLTE) Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Main Body ECU)



OK

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.
U189994E02
1.875,1.823 2.344,2.042 false 1.875,2.063 2.094,2.479 false 0.375,0.302 0.604,0.521 0.229,0.219 10 false *a 2.406,1.99 2.833,2.167 0.427,0.177 10 false CLTE 1.625,0.719 1.875,0.896 0.25,0.177 10 false H1 1.927,2.531 2.354,2.708 0.427,0.177 10 false CLTS

Reconnect the H1 automatic light control sensor connector.


b.

Connect an oscilloscope to the automatic light control sensor connector.

Text in Illustration
*a Component with harness connected
(Automatic Light Control Sensor)


c.
B113714E28
2.948,1.063 3.292,1.219 0.344,0.156 10 GND 1.844,1.177 1.969,1.333 0.125,0.156 10 A

Check the waveform.

OK:
Tester Connection Tool Setting Condition Specified Condition
H1-3 (CLTE) - H1-5 (CLTS) 5 V/DIV., 5 ms./DIV. Engine switch on (IG), light control switch in AUTO position Correct waveform is as shown


HINT:

If the ambient light becomes brighter, width A becomes narrower.




OK

REPLACE MAIN BODY ECU

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR