Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291968 LIGHTING SYSTEM(for LED Headlight) J

LIGHTING  LIGHTING SYSTEM(for LED Headlight)  Interior Light Circuit  


DESCRIPTION

The main body ECU receives information regarding the door lock position switch and engine switch, and turns on each inside handle illumination light.

HINT:

The inside handle illumination lights are the lights which illuminate the drink holders on the front doors and rear slide doors.


WIRING DIAGRAM

E350946E01
2.723,0.307 3.617,0.507 0.894,0.200 10 from Battery 6.345,1.015 6.794,1.214 0.450,0.200 10 FSPT 1.763,0.454 2.227,0.654 0.463,0.200 10 DOME 6.074,1.017 6.278,1.214 0.205,0.198 10 11 2.389,1.038 2.597,1.246 0.208,0.208 10 1 4.056,1.038 4.264,1.246 0.208,0.208 10 2 2.389,2.215 2.597,2.423 0.208,0.208 10 1 4.056,2.215 4.264,2.423 0.208,0.208 10 2 2.389,3.385 2.597,3.593 0.208,0.208 10 1 4.056,3.385 4.264,3.593 0.208,0.208 10 2 2.389,4.555 2.597,4.762 0.208,0.208 10 1 4.056,4.555 4.264,4.762 0.208,0.208 10 2 6.095,6.173 7.153,6.356 1.059,0.184 10 Main Body ECU 6.095,5.988 6.447,6.172 0.353,0.184 10 G59 2.06,1.5 2.306,1.684 0.246,0.184 10 L4 2.361,1.5 4.954,1.684 2.593,0.184 10 Rear Inside Handle Illumination Light LH 2.06,2.677 2.306,2.861 0.246,0.184 10 K4 2.361,2.677 4.954,2.861 2.593,0.184 10 Rear Inside Handle Illumination Light RH 2.06,3.847 2.306,4.031 0.246,0.184 10 I8 2.361,3.847 4.954,4.031 2.593,0.184 10 Front Inside Handle Illumination Light RH 2.06,5.031 2.306,5.215 0.246,0.184 10 J8 2.361,5.031 4.954,5.215 2.593,0.184 10 Front Inside Handle Illumination Light LH

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (INTERIOR LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Main body
Tester Display Test Part Control Range Diagnostic Note
Fr Foot Light Inside handle illumination lights ON / OFF -

OK:

Inside handle illumination light illuminates.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY - INSIDE HANDLE ILLUMINATION LIGHT)
2.CHECK HARNESS AND CONNECTOR (BATTERY - INSIDE HANDLE ILLUMINATION LIGHT)
a.

Disconnect the J8 front inside handle illumination light LH connector.


b.

Disconnect the I8 front inside handle illumination light RH connector.


c.

Disconnect the L4 rear inside handle illumination light LH connector.


d.

Disconnect the K4 rear inside handle illumination light RH connector.


e.

Measure the voltage of the wire harness side connector.

Standard Voltage:
Tester Connection Condition Specified Condition
J8-1 - Body ground Always 11 to 14 V
I8-1 - Body ground Always 11 to 14 V
L4-1 - Body ground Always 11 to 14 V
K4-1 - Body ground Always 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (INSIDE HANDLE ILLUMINATION LIGHT - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INSIDE HANDLE ILLUMINATION LIGHT - MAIN BODY ECU)
a.

Disconnect the G59 main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L4-2 - G59-11 (FSPT) Always Below 1 Ω
K4-2 - G59-11 (FSPT) Always Below 1 Ω
I8-2 - G59-11 (FSPT) Always Below 1 Ω
J8-2 - G59-11 (FSPT) Always Below 1 Ω
L4-2 or G59-11 (FSPT) - Body ground Always 10 kΩ or higher
K4-2 or G59-11 (FSPT) - Body ground Always 10 kΩ or higher
I8-2 or G59-11 (FSPT) - Body ground Always 10 kΩ or higher
J8-2 or G59-11 (FSPT) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR