AUTOMATIC LIGHT CONTROL SYSTEM
When the light control switch is in the AUTO position, the automatic light control system detects ambient light levels and controls the low beam headlights, clearance lights, taillights and license plate lights.
LIGHT AUTO TURN-OFF SYSTEM
The light auto turn-off system is used to prevent the exterior lights (low beam headlights, high beam headlights, taillights, clearance lights and license plate lights) from being accidentally left on.
The lights that will turn off vary depending on the position of the light control switch as shown in the table below.
| Switch Condition | Outline |
|---|---|
| Light control switch in AUTO position | When the exterior lights are on, they are automatically turned off when the engine switch is turned from on (IG) to off. |
| Light control switch in tail or head position | When the exterior lights are on, the low beam headlights and high beam headlights are automatically turned off when the engine switch is turned from on (IG) to off.
|
DAYTIME LIGHT SYSTEM
The daytime light control is designed to illuminate the daytime lights during the daytime to make the vehicle more visible to other vehicles.
This system is controlled by the main body ECU.
This system is enabled when the following conditions are met:
The engine switch is on (IG).
The light control switch is in the off or AUTO position (and the low beam headlights are not turned on by the automatic light control system).
The parking brake switch is off.
AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM
Initialize the rear height control sensor sub-assembly LH signal after the vehicle height changes due to replacement of suspension components or after operations such as reinstallation or replacement of the rear height control sensor sub-assembly LH.
When the headlight leveling ECU assembly is replaced, initialization is also necessary.
General
This system maintains the low beam headlights at a constant level while the vehicle is being stopped.
This system is controlled by the headlight leveling ECU assembly. The headlight leveling ECU assembly detects the vehicle posture via the rear height control sensor sub-assembly LH, and detects the vehicle speed via the combination meter sub-assembly. The headlight leveling ECU assembly controls each headlight leveling motor based on this information in order to change the headlight reflector angle.
Function of Main Components
| Component | Outline |
|---|---|
| Rear Height Control Sensor Sub-assembly LH | Detects vehicle height. |
| Combination Meter Sub-assembly | ·
Outputs the vehicle speed signal to the headlight leveling ECU assembly. ·
If this system malfunctions, "Headlight System Malfunction Visit Your Dealer" will be displayed on the multi-information display in accordance with the signal from the headlight leveling ECU assembly. |
| Headlight Leveling Motor | Based on the signals received from the headlight leveling ECU assembly, each motor moves the reflector in the headlight to change its low beam angle. |
| Headlight Leveling ECU Assembly | ·
Based on the signals that are transmitted by the rear height control sensor sub-assembly LH and combination meter assembly, the headlight leveling ECU assembly detects the amount of variance of the vehicle posture while the vehicle is stopping. ·
Based on the detected value, the headlight leveling ECU assembly outputs control signals to the headlight leveling motor. ·
To headlight leveling ECU assembly sends a signal to display "Headlight System Malfunction Visit Your Dealer" on the multi-information display to alert the driver when a malfunction in this system is detected. |
LIGHTING SYSTEM (INTERIOR)
Illumination control function (Illuminated entry function):
When the doors are unlocked through a key or transmitter operation, or when a door is opened or closed, the illuminated entry function turns on the map light, room light, engine switch light and inside handle illumination light.
The main body ECU receives the following signals (A).
Door courtesy switch signal
Door detection switch signal
Engine switch signal
The main body ECU controls the following signal based on the signals listed in A.
Illumination operation signal
The main body ECU controls the on/off and fade-in/fade-out operation of the following parts.
Map light
Room light
Inside handle illumination light
Engine switch light
Battery saver function:
When the engine switch is turned off and any of the doors is open continuously for 20 minutes, the main body ECU turns the illumination operation signal off. As a result, the map light, the room light and the inside handle illumination light turn off.
The main body ECU receives the following signals (B).
Door courtesy switch signal
Engine switch signal
The main body ECU controls the following signal based on the signals listed in B (C).
Illumination operation signal
The main body ECU controls the illumination period of the following parts based on the signals listed in C.
Map light
Room light
Inside handle illumination light