Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291968 LIGHTING SYSTEM(for LED Headlight) J

LIGHTING  LIGHTING SYSTEM(for LED Headlight)  Daytime Running Light Relay Circuit  


DESCRIPTION

The main body ECU controls the daytime lights.

WIRING DIAGRAM

E349363E04
4.979,0.563 5.594,0.76 0.615,0.198 10 false DRLE 3.135,1.406 3.75,1.604 0.615,0.198 10 false DRL 1.917,0.813 2.531,1.01 0.615,0.198 10 false DRL 0.479,0.625 1.271,1 0.792,0.375 10 false from Battery 4.708,1.625 5.323,1.823 0.615,0.198 10 false G58 1.667,4.823 2.281,5.021 0.615,0.198 10 false C12 1.99,3.146 3.781,3.323 1.792,0.177 10 false LED Illumination Light RH 2.021,4.833 3.813,5.01 1.792,0.177 10 false LED Illumination Light LH 1.938,2.396 2.552,2.594 0.615,0.198 10 false E 3.167,2.396 3.781,2.594 0.615,0.198 10 false B 3.219,4.073 3.833,4.271 0.615,0.198 10 false B 1.99,4.073 2.604,4.271 0.615,0.198 10 false E 3.365,2.385 3.979,2.583 0.615,0.198 10 false 2 3.406,4.063 4.021,4.26 0.615,0.198 10 false 2 1.74,2.365 2.354,2.563 0.615,0.198 10 false 3 1.792,4.063 2.406,4.26 0.615,0.198 10 false 3 2.792,1.01 3.406,1.208 0.615,0.198 10 false 3 2.771,0.552 3.385,0.75 0.615,0.198 10 false 1 3.615,0.563 4.229,0.76 0.615,0.198 10 false 2 3.625,1 4.24,1.198 0.615,0.198 10 false 5 4.792,0.552 5.406,0.75 0.615,0.198 10 false 8 4.719,1.844 6.458,2.24 1.74,0.396 10 false Main Body ECU 1.615,3.135 2.229,3.333 0.615,0.198 10 false C11

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Daytime Running Light Daytime Lights ON/OFF -

OK:

Daytime lights illuminate.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT DRL RELAY
2.INSPECT DRL RELAY
a.
E222294E42
1.104,0.948 1.302,0.5 1.302,0.5 1.438,0.5 false 1.063,1.344 1.146,1.76 1.146,1.76 1.344,1.76 false 0.792,1 0.906,0.51 0.906,0.51 1.031,0.51 false 0.563,1.271 0.635,1.75 0.635,1.75 0.823,1.75 false 1.458,0.427 1.563,0.583 0.104,0.156 10 false 1 1.375,1.667 1.479,1.823 0.104,0.156 10 false 2 1.063,0.427 1.167,0.583 0.104,0.156 10 false 5 0.177,0.177 0.333,0.333 0.156,0.156 10 false *a 0.844,1.667 0.948,1.823 0.104,0.156 10 false 3

Remove the DRL relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω


Text in Illustration
*a Component without harness connected
(DRL relay)



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY - DRL RELAY)

NG

REPLACE DRL RELAY

3.CHECK HARNESS AND CONNECTOR (BATTERY - DRL RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (DRL relay terminal) - Body ground Always 11 to 14 V
3 (DRL relay terminal) - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (DRL RELAY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DRL RELAY - MAIN BODY ECU)
a.

Disconnect the G58 main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (DRL relay terminal) - G58-8 (DRLE) Always Below 1 Ω
2 (DRL relay terminal) or G58-8 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (DRL RELAY - LED ILLUMINATION LIGHT ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DRL RELAY - LED ILLUMINATION LIGHT ASSEMBLY AND BODY GROUND)
a.

Disconnect the C11 LED illumination light RH connector.


b.

Disconnect the C12 LED illumination light LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (DRL terminal) - C11-2 (B) Always Below 1 Ω
5 (DRL terminal) - C12-2 (B) Always Below 1 Ω
5 (DRL terminal) or C11-2 (B) - Body ground Always 10 kΩ or higher
5 (DRL terminal) or C12-2 (B) - Body ground Always 10 kΩ or higher
C11-3 (E) - Body ground Always Below 1 Ω
C12-3 (E) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR