Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291968 LIGHTING SYSTEM(for LED Headlight) J

LIGHTING  LIGHTING SYSTEM(for LED Headlight)  Headlight Solenoid Circuit  


DESCRIPTION

When the main body ECU receives a high beam turn on signal, the main body ECU activates the bi-function by controlling the DIM relay. The bi-function increases the upper illumination area of the low beam by moving a shade using a solenoid built into the headlight assembly.



WIRING DIAGRAM

E349404E05
4.938,1.76 5.25,1.958 0.313,0.198 10 false 4P 5.219,1.781 6.406,2.083 1.188,0.302 10 false Main Body ECU 3.313,1.552 3.625,1.75 0.313,0.198 10 false DIM 6.052,0.719 6.365,0.917 0.313,0.198 10 false DIM 3.177,2.458 3.802,2.667 0.625,0.208 10 false H-LP RH 3.188,4.802 3.813,5.01 0.625,0.208 10 false H-LP LH 2.813,4.552 3.052,4.719 0.24,0.167 10 false 3 2.813,4.896 3.052,5.063 0.24,0.167 10 false 7 2.063,4.563 2.302,4.729 0.24,0.167 10 false 2 2.073,4.896 2.313,5.063 0.24,0.167 10 false 6 2.073,2.229 2.313,2.396 0.24,0.167 10 false 2 2.073,2.563 2.313,2.729 0.24,0.167 10 false 6 2.823,2.219 3.063,2.385 0.24,0.167 10 false 3 2.823,2.563 3.063,2.729 0.24,0.167 10 false 7 3.802,1.156 4.042,1.323 0.24,0.167 10 false 5 2.958,1.177 3.198,1.344 0.24,0.167 10 false 3 2.948,0.708 3.188,0.875 0.24,0.167 10 false 2 3.802,0.719 4.042,0.885 0.24,0.167 10 false 1 1.073,0.823 2.167,1.01 1.094,0.188 10 false from H-LP Relay 2.625,2.552 2.865,2.719 0.24,0.167 10 false E 2.448,4.563 2.865,4.729 0.417,0.167 10 false SOL 2.479,2.25 2.896,2.417 0.417,0.167 10 false SOL 2.615,4.875 2.854,5.042 0.24,0.167 10 false E 0.563,3.667 0.938,3.833 0.375,0.167 10 false B30 0.542,6.042 0.813,6.208 0.271,0.167 10 false B31 0.677,2.969 2.073,3.146 1.396,0.177 10 false Headlight Unit RH 0.677,3.271 2.448,3.458 1.771,0.188 10 false Headlight Unit Assembly RH 0.896,3.656 2.667,3.844 1.771,0.188 10 false Headlight Assembly RH 0.656,5.354 2.052,5.531 1.396,0.177 10 false Headlight Unit LH 0.667,5.667 2.438,5.854 1.771,0.188 10 false Headlight Unit Assembly LH 0.854,6.042 2.625,6.229 1.771,0.188 10 false Headlight Assembly LH 4.75,0.729 4.99,0.896 0.24,0.167 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Reform the Active Test according to the display on the GTS.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Head Light Hi High beam headlights ON/OFF -

OK:

High beam headlights illuminate.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT DIM RELAY
2.INSPECT DIM RELAY
a.

Remove the DIM relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.
E316295E05
2.521,1.167 2.615,1.094 false 2.917,0.969 3.021,1.031 false 2.583,1.552 2.688,1.427 false 2.25,1.365 2.25,1.49 false 0.385,0.844 0.698,1.063 0.313,0.219 10 false 3 2.396,1.125 2.708,1.427 0.313,0.302 10 false 3 2.229,1.51 2.542,1.813 0.313,0.302 10 false 2 1.625,0.854 1.938,1.156 0.313,0.302 10 false 5 0.396,1.292 0.708,1.594 0.313,0.302 10 false 2 1.615,1.292 1.927,1.594 0.313,0.302 10 false 1 2.792,0.865 3.104,1.167 0.313,0.302 10 false 1 2.719,1.313 3.031,1.615 0.313,0.302 10 false 5 0.177,0 0.49,0.302 0.313,0.302 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage not applied between terminals 1 and 2 Below 1 Ω
3 - 5 Voltage applied between terminals 1 and 2 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(DIM relay)



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - DIM RELAY)

NG

REPLACE DIM RELAY

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - DIM RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (DIM relay terminal) - Body ground Always 11 to 14 V
3 (DIM relay terminal) - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (DIM RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DIM RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
a.

Disconnect the B31 headlight assembly LH connector.


b.

Disconnect the B30 headlight assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
5 (DIM relay terminal) - B31-3 (SOL) Always Below 1 Ω
5 (DIM relay terminal) - B30-3 (SOL) Always Below 1 Ω
5 (DIM relay terminal) or B31-3 (SOL) - Body ground Always 10 kΩ or higher
5 (DIM relay terminal) or B30-3 (SOL) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (DIM RELAY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DIM RELAY - MAIN BODY ECU)
a.

Disconnect the 4P main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (DIM relay terminal) - 4P-8 Always Below 1 Ω
1 (DIM relay terminal) or 4P-8 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR