Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291968 LIGHTING SYSTEM(for LED Headlight) J

LIGHTING  LIGHTING SYSTEM(for LED Headlight)  Low Beam Headlight Circuit  


DESCRIPTION

The main body ECU controls the low beam headlights.

WIRING DIAGRAM

E349352E03
5.354,1.552 6.344,2.052 0.99,0.5 10 false Main Body ECU 6.313,0.563 6.802,0.833 0.49,0.271 10 false HRLY 5.354,1.344 5.844,1.615 0.49,0.271 10 false 4L 4.969,0.438 5.458,0.708 0.49,0.271 10 false 6 4.219,0.427 4.708,0.698 0.49,0.271 10 false 1 4.219,0.865 4.708,1.135 0.49,0.271 10 false 3 3.677,1.281 4.167,1.552 0.49,0.271 10 false H-LP 3.375,0.427 3.865,0.698 0.49,0.271 10 false 2 3.385,0.885 3.875,1.156 0.49,0.271 10 false 5 1.25,0.552 2.604,1.24 1.354,0.688 10 false from Battery 3.458,1.917 4.219,2.156 0.76,0.24 10 false H-LP RL 3.448,5.188 4.208,5.427 0.76,0.24 10 false H-LP LL 3.156,1.688 3.917,1.927 0.76,0.24 10 false 4 2.948,1.677 3.708,1.917 0.76,0.24 10 false B 2.99,2.667 3.75,2.906 0.76,0.24 10 false E 3.167,2.667 3.927,2.906 0.76,0.24 10 false 8 2.969,4.969 3.729,5.208 0.76,0.24 10 false B 3.177,4.969 3.938,5.208 0.76,0.24 10 false 4 2.969,5.813 3.729,6.052 0.76,0.24 10 false E 3.177,5.813 3.938,6.052 0.76,0.24 10 false 8 1.01,3.135 2.458,3.438 1.448,0.302 10 false Headlight Unit RH 1,6.344 2.448,6.646 1.448,0.302 10 false Headlight Unit LH 0.698,3.979 1.458,4.219 0.76,0.24 10 false B30 1.01,3.969 2.458,4.271 1.448,0.302 10 false Headlight Assembly RH 1.063,7.156 2.594,7.375 1.531,0.219 10 false Headlight Assembly LH 0.708,7.156 1.469,7.396 0.76,0.24 10 false B31 1.01,3.552 2.781,3.813 1.771,0.26 10 false Headlight Unit Assembly RH 1,6.729 2.76,6.948 1.76,0.219 10 false Headlight Unit Assembly LH 2.729,1.688 3.49,1.927 0.76,0.24 10 false 1 2.719,2.677 3.479,2.917 0.76,0.24 10 false 5 2.729,4.969 3.49,5.208 0.76,0.24 10 false 1 2.74,5.833 3.5,6.073 0.76,0.24 10 false 5 1.469,2 2.333,2.469 0.865,0.469 10 false Light Control ECU RH 1.458,5.219 2.458,5.708 1,0.49 10 false Light Control ECU LH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Headlight Relay Headlight relay (Low beam headlights) ON/OFF -

OK:

Headlight relay operates. (Low beam headlights illuminate.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT H-LP RELAY
2.INSPECT H-LP RELAY
a.

Remove the H-LP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.
E316295E06
2.531,1.208 2.625,1.135 false 2.917,0.958 3.021,1.021 false 2.615,1.542 2.719,1.417 false 2.25,1.344 2.25,1.469 false 0.385,0.844 0.698,1.146 0.313,0.302 11 false 3 2.427,1.156 2.74,1.458 0.313,0.302 10 false 3 2.229,1.49 2.542,1.792 0.313,0.302 10 false 2 1.625,0.854 1.938,1.156 0.313,0.302 11 false 5 0.385,1.26 0.698,1.563 0.313,0.302 11 false 2 1.615,1.271 1.927,1.573 0.313,0.302 11 false 1 2.813,0.833 3.125,1.135 0.313,0.302 10 false 1 2.708,1.25 3.021,1.552 0.313,0.302 10 false 5 0.156,0.135 0.604,0.323 0.448,0.188 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage applied between terminals 1 and 2 Below 1 Ω


Text in Illustration
*a Component without harness connected
(H-LP relay)



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RELAY)

NG

REPLACE H-LP RELAY

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (H-LP relay terminal) - Body ground Always 11 to 14 V
5 (H-LP relay terminal) - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
a.

Disconnect the B31 headlight assembly LH connector.


b.

Disconnect the B30 headlight assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (H-LP terminal) - B30-4 (B) Always Below 1 Ω
3 (H-LP terminal) - B31-4 (B) Always Below 1 Ω
3 (H-LP terminal) or B30-4 (B) - Body ground Always 10 kΩ or higher
3 (H-LP terminal) or B31-4 (B) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - MAIN BODY ECU)
a.

Disconnect the 4L main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (H-LP terminal) - 4L-6 Always Below 1 Ω
1 (H-LP terminal) or 4L-6 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR