Home › Vehicle Interior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM24M0E _58 Vehicle Interior _059565 WIPER / WASHER _0291969 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Headlight Cleaner Switch Circuit  


DESCRIPTION

This circuit detects the conditions of the headlight cleaner switch.

WIRING DIAGRAM

E132117E02
0.073,3.229 0.354,3.396 0.281,0.167 10 false A26 0.063,3.396 2.073,3.594 2.01,0.198 10 false Headlight Cleaner Control Relay 0.854,1.01 1.323,1.156 0.469,0.146 10 false HDLO 1.365,1.115 1.594,1.333 0.229,0.219 10 false 1 1.375,2.635 1.594,2.813 0.219,0.177 10 false 2 3.125,2.625 3.281,2.771 0.156,0.146 10 false 8 4.156,2.635 4.313,2.781 0.156,0.146 10 false 5 1.135,2.5 1.281,2.688 0.146,0.188 10 false H 2.844,3.104 4.469,3.26 1.625,0.156 10 false Headlight Cleaner Switch 2.823,2.927 3.281,3.083 0.458,0.156 10 false G38 5.854,3.188 6.26,3.427 0.406,0.24 10 false 4L 5.844,3.396 6.875,3.552 1.031,0.156 10 false Main Body ECU 5.927,1.01 6.344,1.156 0.417,0.146 10 false HRLY 5.656,1.115 5.792,1.333 0.135,0.219 10 false 6

PROCEDURE

1.INSPECT HEADLIGHT CLEANER SWITCH
E125000

a.

Remove the headlight cleaner switch.


b.

Measure the resistance of the switch.

Standard resistance:
Tester Connection Switch Condition Specified Condition
5 - 8 ON Below 25 Ω
OFF 10 kΩ or higher




OK

2.CHECK WIRE HARNESS (SWITCH - ECU AND RELAY)

NG

REPLACE HEADLIGHT CLEANER SWITCH

2.CHECK WIRE HARNESS (SWITCH - ECU AND RELAY)
U189883E02
3.521,2.073 4.302,1.76 true 5.365,2.427 5.365,3.208 true 3.323,2.125 2.656,2.427 true 0.135,0.063 1.417,0.219 1.281,0.156 10 false Wire Harness Side: 5.625,1.208 5.823,1.365 0.198,0.156 10 false 4L 5.198,0.74 6.219,0.885 1.021,0.146 10 false Main Body ECU 3.365,1.396 3.656,1.552 0.292,0.156 10 false A26 0.656,0.896 2.302,1.052 1.646,0.156 10 false Headlight Cleaner Switch 2.458,0.896 4.51,1.083 2.052,0.188 10 false Headlight Cleaner Control Relay 1.302,1.333 1.615,1.49 0.313,0.156 10 false G38 4.385,1.656 4.625,1.823 0.24,0.167 10 false H 5.135,3.25 5.573,3.406 0.438,0.156 10 false HRLY 2.406,2.458 2.813,2.615 0.406,0.156 10 false HOLD

a.

Disconnect the G38 switch connector.


b.

Disconnect the A26 relay connector


c.

Disconnect the 4L ECU connector.


d.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G38-8 - A26-2 (H) Below 1 Ω
G38-5 - 4L-6 (HRLY)
A26-1 (HDLO) - 4L-6 (HRLY)
A26-1 (HDLO) - Body ground 10 kΩ or higher
A26-2 (H) - Body ground
G38-5 - Body ground




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR