Home › Vehicle Interior › WIPER / WASHER › WIPER SWITCH
RM24M0E _58 Vehicle Interior _059565 WIPER / WASHER _0291972 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WIPER AND WASHER SWITCH ASSEMBLY

a.

Check the front wiper switch.

U189869E02
1.531,2.021 1.604,2.417 true 1.458,2.406 1.167,2.01 true 1.865,1.99 1.948,2.417 true 2.188,1.99 2.083,2.396 true 2.302,2.406 2.521,1.979 true 2.438,2.417 2.792,1.99 true 5.719,2 5.615,2.427 true 5.771,2.396 6.094,2.01 true 5.406,2 5.313,2.427 true 5.094,1.99 5.135,2.396 true 4.948,2.406 4.74,1.99 true 4.813,2.427 4.479,1.99 true 2.063,2.99 2.344,3.135 0.281,0.146 10 false G12 1.365,2.99 1.646,3.156 0.281,0.167 10 false G13 0.958,1.833 1.229,2.01 0.271,0.177 10 false EW 1.396,1.833 1.667,2 0.271,0.167 10 false WF 2.792,1.833 3.031,2 0.24,0.167 10 false +2 2.469,1.833 2.708,2 0.24,0.167 10 false +1 1.75,1.833 1.99,1.99 0.24,0.156 10 false +S 2.104,1.833 2.344,2 0.24,0.167 10 false +B 5.146,0.229 5.729,0.396 0.583,0.167 10 false for LHD: 1.573,0.281 2.188,0.438 0.615,0.156 10 false for RHD: 5.615,3.01 5.896,3.156 0.281,0.146 10 false G13 4.896,3 5.177,3.167 0.281,0.167 10 false G12 6.031,1.823 6.302,2 0.271,0.177 10 false EW 5.635,1.823 5.906,1.99 0.271,0.167 10 false WF 4.323,1.823 4.563,1.99 0.24,0.167 10 false +2 4.646,1.823 4.885,1.99 0.24,0.167 10 false +1 5.302,1.823 5.542,1.979 0.24,0.156 10 false +S 4.958,1.823 5.198,1.99 0.24,0.167 10 false +B

i.

Measure the resistance of the switch.

Standard resistance (for LHD):
Tester Connection Switch Condition Specified Condition
G12-1 (+S) - G12-3 (+1) INT Below 1 Ω
OFF
G12-2 (+B) - G12-3 (+1) MIST
LO
G12-2 (+B) - G12-4 (+2) HI


Standard resistance (for RHD):
Tester Connection Switch Condition Specified Condition
G12-4 (+S) - G12-2 (+1) INT Below 1 Ω
OFF
G12-3 (+B) - G12-2 (+1) MIST
LO
G12-3 (+B) - G12-1 (+2) HI


If the result is not as specified, replace the switch assembly.



b.

Check the front washer switch.

i.

Measure the resistance of the switch.

Standard resistance (for LHD) :
Tester Connection Switch Condition Specified Condition
G13-2 (EW) - G13-3 (WF) ON Below 1 Ω
OFF 10 kΩ or higher


Standard resistance (for RHD):
Tester Connection Switch Condition Specified Condition
G13-2 (EW) - G13-1 (WF) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not specified, replace the switch assembly.



c.

Check the intermittent operation. (for LHD)

i.

Connect the voltmeter's positive (+) lead to terminal G12-3 (+1) and the negative (-) lead to terminal G13-2 (EW).


ii.

Connect the battery's positive (+) lead to terminal G12-2 (+B) and the negative (-) lead to terminal G13-2 (EW) and G12-1 (+S).


iii.

Turn the wiper switch to the INT position.


iv.

Connect the battery's positive (+) lead to terminal G12-1 (+S) for 5 seconds.


v.

Connect the battery's negative (-) lead to terminal G12-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals G12-3 (+1) and G13-2 (EW).

Standard voltage:

Refer to the illustration below.


E056399E72
0.135,0.938 1.958,1.271 1.823,0.333 10 false Voltage between terminals G12-3 (+1) and G13-2 (EW) 1.729,0.583 2.448,0.729 0.719,0.146 10 false 10 to 14 V 2.198,1.063 2.469,1.219 0.271,0.156 10 false 0 V 2.479,1.458 3.542,1.625 1.063,0.167 10 false 1.6 +-1 second 2.833,0.125 4.823,0.479 1.99,0.354 10 false FAST: Connect battery negative lead to terminal G12-1 (+S) 4.906,0.125 7.01,0.521 2.104,0.396 10 false SLOW: Connect battery negative lead to terminal G12-1 (+S) 4.625,1.458 5.823,1.615 1.198,0.156 10 false 10.7 +-5 seconds

If the result is not as specified, replace the switch assembly.



d.

Check the intermittent operation. (for RHD)

i.

Connect the voltmeter's positive (+) lead to terminal G12-2 (+1) and the negative (-) lead to terminal G13-2 (EW).


ii.

Connect the battery's positive (+) lead to terminal G12-3 (+B) and the negative (-) lead to terminal G13-2 (EW) and G12-4 (+S).


iii.

Turn the wiper switch to the INT position.


iv.

Connect the battery's positive (+) lead to terminal G12-4 (+S) for 5 seconds.


v.

Connect the battery's negative (-) lead to terminal G12-4 (+S). Operate the intermittent wiper relay and check the voltage between terminals G12-2 (+1) and G13-2 (EW).

Standard voltage:

Refer to the illustration below.


E056399E73
0.135,0.927 2.021,1.25 1.885,0.323 10 false Voltage between terminals G12-2 (+1) and G13-2 (EW) 1.729,0.604 2.448,0.75 0.719,0.146 10 false 10 to 14 V 2.198,1.083 2.469,1.24 0.271,0.156 10 false 0 V 2.51,1.469 3.573,1.635 1.063,0.167 10 false 1.6 +-1 second 2.781,0.083 4.771,0.438 1.99,0.354 10 false FAST: Connect battery negative lead to terminal G12-4 (+S) 4.865,0.094 7.073,0.438 2.208,0.344 10 false SLOW: Connect battery negative lead to terminal G12-4 (+S) 4.688,1.469 5.885,1.625 1.198,0.156 10 false 10.7 +-5 seconds

If the result is not as specified, replace the switch assembly.



e.

Check the front washer operation. (for LHD)

i.

Turn the wiper switch OFF.


ii.

Connect the battery's positive (+) lead to terminal G12-2 (+B) and the negative (-) lead to terminals G12-4 (+S) and G13-2 (EW).


iii.

Connect the voltmeter's positive (+) lead to G12-3 (+1) and the negative (-) lead to terminal G13-2 (EW).


iv.

Turn the washer switch ON and OFF, and check the voltage between terminals G12-3 (+1) and G13-2 (EW).

OK:

Refer to the illustration below.


E125344E52
2.938,1.323 2.896,1.438 false 3.594,1.313 3.74,1.427 false 0.063,1.135 1.802,1.51 1.74,0.375 10 false Voltage between terminals G12-3 (+1) and G13-2 (EW) 0.604,0.667 1.563,0.823 0.958,0.156 10 false Washer Switch 2.313,1.188 2.677,1.344 0.365,0.156 10 false 0 V 2.313,0.729 2.677,0.885 0.365,0.156 10 false OFF 2.365,0.531 2.635,0.688 0.271,0.156 10 false ON 2.042,0.99 2.729,1.135 0.688,0.146 10 false 10 to 14 V 1.833,1.469 3.563,1.615 1.729,0.146 10 false Approximately 0.3 seconds 3.594,1.469 5.323,1.615 1.729,0.146 10 false Approximately 2.2 seconds

If the result is not as specified, replace the switch assembly.



f.

Check the front washer operation. (for RHD)

i.

Turn the wiper switch OFF.


ii.

Connect the battery's positive (+) lead to terminal G12-3 (+B) and the negative (-) lead to terminals G12-1 (+S) and G13-2 (EW).


iii.

Connect the voltmeter's positive (+) lead to G12-2 (+1) and the negative (-) lead to terminal G13-2 (EW).


iv.

Turn the washer switch ON and OFF, and check the voltage between terminals G12-2 (+1) and G13-2 (EW).

OK:

Refer to the illustration below.


E125344E53
2.938,1.323 2.896,1.438 false 3.594,1.313 3.74,1.427 false 0.021,1.115 1.823,1.427 1.802,0.313 10 false Voltage between terminals G12-2 (+1) and G13-2 (EW) 0.594,0.667 1.552,0.823 0.958,0.156 10 false Washer Switch 2.313,1.135 2.677,1.292 0.365,0.156 10 false 0 V 2.313,0.688 2.677,0.844 0.365,0.156 10 false OFF 2.375,0.5 2.646,0.656 0.271,0.156 10 false ON 2.042,0.938 2.729,1.083 0.688,0.146 10 false 10 to 14 V 1.792,1.438 3.521,1.583 1.729,0.146 10 false Approximately 0.3 seconds 3.573,1.448 5.302,1.594 1.729,0.146 10 false Approximately 2.2 seconds

If the result is not as specified, replace the switch assembly.



g.

Check the rear wiper switch.

U189870E02
5.771,2.417 6.167,2.208 true 5.292,2.635 5.198,2.99 true 5.625,2.635 5.688,2.969 true 5.99,2.99 5.719,2.615 true 1.448,2.406 1.073,2.188 true 1.927,2.635 2.042,2.99 true 1.604,2.625 1.552,2.979 true 1.26,2.99 1.51,2.615 true 2.083,1.875 2.365,2.021 0.281,0.146 10 false G12 1.365,1.875 1.646,2.042 0.281,0.167 10 false G13 5.094,0.188 5.677,0.354 0.583,0.167 10 false for LHD: 1.615,0.24 2.229,0.396 0.615,0.156 10 false for RHD: 5.656,1.896 5.938,2.042 0.281,0.146 10 false G13 4.938,1.896 5.219,2.063 0.281,0.167 10 false G12 6.271,2.073 6.542,2.25 0.271,0.177 10 false EW 5.083,3.01 5.375,3.177 0.292,0.167 10 false WR 5.958,3.021 6.323,3.177 0.365,0.156 10 false C1R 5.531,3.021 5.854,3.177 0.323,0.156 10 false +1R 1.958,3.021 2.25,3.188 0.292,0.167 10 false WR 0.781,2.031 1.052,2.208 0.271,0.177 10 false EW 1.031,3.031 1.365,3.188 0.333,0.156 10 false C1R 1.427,3.031 1.75,3.188 0.323,0.156 10 false +1R

i.

Measure the resistance of the switch.

Standard resistance (for LHD):
Tester Connection Switch Condition Specified Condition
G13-2 (EW) - G13-6 (C1R) LO Below 1 Ω
G13-2 (EW) - G13-6 (+1R) HI
G13-2 (EW) - G13-6 (C1R) OFF 10 kΩ or higher
G13-2 (EW) - G13-6 (+1R)


Standard resistance (for RHD):
Tester Connection Switch Condition Specified Condition
G13-2 (EW) - G13-5 (C1R) LO Below 1 Ω
G13-2 (EW) - G13-4 (+1R) HI
G13-2 (EW) - G13-5 (C1R) OFF 10 kΩ or higher
G13-2 (EW) - G13-4 (+1R)


If the result is not as specified, replace the switch assembly.



h.

Check the rear washer switch.

i.

Measure the resistance of the switch.

Standard resistance (for LHD) :
Tester Connection Switch Condition Specified Condition
G13-2 (EW) - G12-5 (WR) ON Below 1 Ω
OFF 10 kΩ or higher


Standard resistance (for RHD):
Tester Connection Switch Condition Specified Condition
G13-2 (EW) - G12-10 (WR) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not specified, replace the switch assembly.