Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM24M0E _56 Audio / Visual / Telematics _059566 AUDIO / VIDEO _0291977 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  01-D6  No Master  01-D7  Connection Check Error  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
01-D6*1 When either condition below is met:
·

The device that stores (stored) the code has (had) been disconnected when the engine switch is on (IG or ACC)

·

The master device has (had) been disconnected when this code is stored


·

Radio receiver power source circuit

·

Power source circuit of the component which has stored this code

·

AVC-LAN circuit between the radio receiver and the component which has stored this code

·

Component which has stored this code

·

Radio receiver


01-D7*2 When either condition below is met:
·

The device that stored the code has (had) been disconnected after the engine starts (started)

·

The master device has (had) been disconnected when this code is (was) stored



HINT:
·

*1: Even if no failure is detected, a trouble code may be recorded depending on the battery condition or engine start voltage.

·

*2: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the engine switch on (IG or ACC), this code is stored.



NOTICE:
·

Before starting troubleshooting, be sure to clear DTCs to erase codes stored due to the reasons described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.

·

The radio receiver is the master unit.

·

Be sure to clear and recheck for DTCs after the inspection is completed to confirm that no DTCs are output.



CAUTION / NOTICE / HINT

NOTICE:

Be sure to read the DESCRIPTION before performing the following procedures.


PROCEDURE

1.CHECK RADIO RECEIVER POWER SOURCE CIRCUIT
a.

Refer to the radio receiver power source circuit (see page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>Radio Receiver Power Source Circuit).

If the power source circuit is operating normally, proceed to the next step.



NEXT

2.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE
2.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE
a.

Enter the diagnostic mode.

E110915E23
1.083,0.781 1.354,0.969 0.271,0.188 10 false *1 1.083,1.323 1.375,1.51 0.292,0.188 10 false *1 1.083,1.854 1.354,2.042 0.271,0.188 10 false *1 1.083,2.354 1.354,2.542 0.271,0.188 10 false *1 1.094,3.24 1.365,3.427 0.271,0.188 10 false *1 0.49,0.698 0.844,0.885 0.354,0.188 10 false *1 4.146,2.594 4.417,2.781 0.271,0.188 10 false *1 4.156,3.042 4.427,3.229 0.271,0.188 10 false *1 4.146,3.635 4.417,3.823 0.271,0.188 10 false *1 4.146,4.156 4.417,4.344 0.271,0.188 10 false *1 4.146,5.01 4.417,5.198 0.271,0.188 10 false *1 4.146,5.896 4.417,6.083 0.271,0.188 10 false *1 3.146,4.479 3.417,4.667 0.271,0.188 10 false *1 4.865,5.896 5.188,6.083 0.323,0.188 10 false *2 4.865,4.99 5.219,5.177 0.354,0.188 10 false *2 4.844,4.156 5.177,4.344 0.333,0.188 10 false *2 4.833,3.635 5.188,3.823 0.354,0.188 10 false *2 4.844,3.052 5.177,3.24 0.333,0.188 10 false *2 4.844,2.594 5.177,2.781 0.333,0.188 10 false *2 6.302,2.469 6.635,2.656 0.333,0.188 10 false *2 1.813,3.24 2.188,3.427 0.375,0.188 10 false *2 1.802,2.354 2.104,2.542 0.302,0.188 10 false *2 1.802,1.854 2.146,2.042 0.344,0.188 10 false *2 1.802,1.323 2.135,1.51 0.333,0.188 10 false *2 1.802,0.781 2.104,0.969 0.302,0.188 10 false *2 2.469,0.708 2.76,0.896 0.292,0.188 10 false *2 3.333,1.896 3.677,2.083 0.344,0.188 10 false *3 2.906,2.323 3.25,2.51 0.344,0.188 10 false *4 0.417,4.979 2.104,5.156 1.688,0.177 10 false *1: SEEK TRACK DOWN 0.427,5.26 1.948,5.438 1.521,0.177 10 false *2: SEEK TRACK UP 0.417,5.531 2.052,5.698 1.635,0.167 10 false *3: PRESET SWITCH "2" 0.427,5.792 2.063,5.958 1.635,0.167 10 false *4: PRESET SWITCH "3" 5.74,3.656 6.063,3.823 0.323,0.167 10 false DTC 3.406,1.26 5.854,1.469 2.448,0.208 10 false Component which has stored this code 2.021,0.198 3.5,0.375 1.479,0.177 10 false Service Check Mode 4.938,0.792 6.823,0.969 1.885,0.177 10 false Detailed Information Mode 3.646,4.479 6.396,4.813 2.75,0.333 10 false Continue to display detailed information of the first code 3.563,5.302 6.656,5.656 3.094,0.354 10 false Continue to display detailed information when more than one DTC is detected 0.458,2.698 2.625,3.073 2.167,0.375 10 false Continue to display when more than two components are installed 0.063,0.042 0.854,0.219 0.792,0.177 10 false Example:


b.

Press the preset switch "3" to change to "Detailed Information Mode".


c.

Identify the component which has stored this code.

Component table
Component Physical address
Television display assembly 1B0

HINT:
·

"440 (stereo component amplifier)" is the component which has stored this code in the example shown in the illustration.

·

For details of the DTC display, refer to the "DTC CHECK / CLEAR" (see page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).





NEXT

3.CHECK POWER SOURCE CIRCUIT OF THE COMPONENT WHICH HAS STORED THIS CODE
3.CHECK POWER SOURCE CIRCUIT OF THE COMPONENT WHICH HAS STORED THIS CODE
a.

Inspect the power source circuit of the component which has stored this code.

If the power source circuit is operating normally, proceed to the next step.

Component table
Component Proceed to
Television display assembly Television display assembly power source circuit



NEXT

4.INSPECT RADIO RECEIVER ASSEMBLY
4.INSPECT RADIO RECEIVER ASSEMBLY
a.
U189877E02
1.635,1.49 1.365,1.896 false 1.813,1.49 2.021,1.906 false 0.417,1.146 0.708,1.323 0.292,0.177 10 false F10 1.146,1.917 1.573,2.063 0.427,0.146 10 false TXM- 1.979,1.917 2.406,2.063 0.427,0.146 10 false TXM+

Disconnect the F10 receiver connector.


b.

Measure the resistance of the receiver.

Standard resistance:
Tester Connection Specified Condition
F10-9 (TXM+) - F10-10 (TXM-) 60 to 80 Ω




OK

5.CHECK WIRE HARNESS (RADIO RECEIVER - COMPONENT WHICH HAS STORED THIS CODE)

NG

REPLACE RADIO RECEIVER ASSEMBLY

5.CHECK WIRE HARNESS (RADIO RECEIVER - COMPONENT WHICH HAS STORED THIS CODE)
HINT:

For details of the connectors, refer to the "Terminals of ECU" (see page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>TERMINALS OF ECU).


a.

Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the radio receiver and the component which has stored this code.

i.

Check for an open or short in the AVC-LAN circuit between the radio receiver and the component which has stored this code.

OK:

There is no open or short circuit.


E130050E04
0.027,0 1.896,0.177 1.869,0.177 10 AVC-LAN Wiring Diagram: 1.539,2.121 3.306,2.284 1.767,0.163 10 Radio Receiver Assembly*1 4.087,2.222 6.035,2.398 1.948,0.177 10 Television Display Assembly*2 2.421,0.946 2.841,1.109 0.420,0.163 10 TXM+ 2.421,1.686 2.841,1.849 0.420,0.163 10 TXM- 4.325,0.946 4.656,1.135 0.331,0.189 10 TX+ 4.325,1.686 4.656,1.875 0.331,0.189 10 TX- 0.147,2.127 1.126,2.314 0.979,0.187 10 *1: Master Unit 0.154,2.401 1.073,2.584 0.920,0.184 10 *2: Slave Unit 1.557,1.944 1.815,2.105 0.258,0.161 10 F10 4.085,2.034 4.408,2.241 0.323,0.207 10 Q21 2.895,1.051 3.215,1.247 0.320,0.195 10 9 4.133,1.048 4.233,1.211 0.100,0.163 10 3 4.143,1.773 4.259,1.942 0.116,0.169 10 4 2.895,1.784 3.188,1.942 0.292,0.158 10 10




OK

6.REPLACE COMPONENT WHICH HAS STORED THIS CODE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE COMPONENT WHICH HAS STORED THIS CODE
a.

Replace the component which has stored this code with a normal one and check if the same problem occurs again.

OK:

Same problem does not occur.




OK

END

NG

REPLACE RADIO RECEIVER ASSEMBLY