Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › 2013.04–2014.09
RM24M0E _56 Audio / Visual / Telematics _059566 AUDIO / VIDEO _0291978 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Sound Signal Circuit between Video Terminal and Television Display  


DESCRIPTION

The video terminal sends sound signals from an external device to the television display assembly.

WIRING DIAGRAM

E254348E01
0.601,2.935 2.400,3.118 1.799,0.184 10 Television Display Assembly 0.601,2.746 0.935,2.929 0.334,0.184 10 Q21 5.371,2.944 6.356,3.128 0.985,0.184 10 Video Terminal 5.329,2.353 5.747,2.537 0.417,0.184 10 SG 1.518,2.353 1.936,2.537 0.417,0.184 10 SGN3 1.518,1.912 1.936,2.096 0.417,0.184 10 SGN6 1.732,1.029 1.938,1.213 0.206,0.184 10 R+ 1.733,1.457 1.938,1.640 0.205,0.184 10 L+ 1.518,0.518 1.936,0.702 0.417,0.184 10 ADPI 5.329,1.919 5.747,2.103 0.417,0.184 10 VA- 5.329,1.471 5.747,1.654 0.417,0.184 10 VAL+ 5.329,0.532 5.747,0.716 0.417,0.184 10 ADPG 5.329,1.043 5.747,1.227 0.417,0.184 10 VAR+ 5.371,2.755 5.705,2.939 0.334,0.184 10 M38 1.984,0.427 2.171,0.611 0.187,0.184 10 18 5.166,0.427 5.271,0.611 0.105,0.184 10 8 5.166,0.917 5.271,1.101 0.105,0.184 10 1 5.166,1.359 5.271,1.542 0.105,0.184 10 2 5.166,1.8 5.271,1.984 0.105,0.184 10 3 5.166,2.241 5.271,2.425 0.105,0.184 10 7 1.984,0.91 2.160,1.094 0.176,0.184 10 22 1.984,1.366 2.160,1.549 0.176,0.184 10 20 1.984,1.786 2.166,1.970 0.182,0.184 10 21 1.984,2.227 2.166,2.411 0.182,0.184 10 19 3.326,2.096 3.905,2.280 0.580,0.184 10 Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - VIDEO TERMINAL)
a.

Disconnect the Q21 television display assembly connector.


b.

Disconnect the M38 video terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q21-22 (R+) - M38-1 (VAR+) Always Below 1 Ω
Q21-20 (L+) - M38-2 (VAL+) Always Below 1 Ω
Q21-21 (SGN6) - M38-3 (VA-) Always Below 1 Ω
Q21-19 (SGN3) - M38-7 (SG) Always Below 1 Ω
Q21-18 (ADPI) - M38-8 (ADPG) Always Below 1 Ω
Q21-22 (R+) - Body ground Always 10 kΩ or higher
Q21-20 (L+) - Body ground Always 10 kΩ or higher
Q21-21 (SGN6) - Body ground Always 10 kΩ or higher
Q21-19 (SGN3) - Body ground Always 10 kΩ or higher
Q21-18 (ADPI) - Body ground Always 10 kΩ or higher




OK

2.INSPECT VIDEO TERMINAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT VIDEO TERMINAL
a.

Reconnect the M38 video terminal connector.


b.
U189921E02
1.833,2.042 2.396,1.531 false 2.031,2.104 2.563,2.104 false 0.125,0.052 0.375,0.25 0.25,0.198 10 false *a 0.563,2.052 0.906,2.24 0.344,0.188 10 false M38 2.458,1.396 2.833,1.583 0.375,0.188 10 false VAL+ 2.615,2.021 3.01,2.208 0.396,0.188 10 false VAR+

Using an oscilloscope, check the signal waveform between each terminal and body ground according to the conditions shown in the table below.

Standard Conditions:
Tester Connection Condition Specified Condition
M38-1 (VAR+) - Body ground RSE system playing (VTR mode) Waveform synchronized with sound signals is output
M38-2 (VAL+) - Body ground RSE system playing (VTR mode) Waveform synchronized with sound signals is output


Text in Illustration
*a Component with harness connected
(Video Terminal)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG