Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › 2013.04–2014.09
RM24M0E _56 Audio / Visual / Telematics _059566 AUDIO / VIDEO _0291978 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Display Signal Circuit between Video Terminal and Television Display  


DESCRIPTION

This is the display signal circuit from the video terminal to the television display assembly.

WIRING DIAGRAM

E254349E02
0.75,2.781 2.552,2.969 1.802,0.188 10 false Television Display Assembly 0.75,2.583 1.083,2.771 0.333,0.188 10 false Q21 5.385,2.76 6.365,2.948 0.979,0.188 10 false Video Terminal 1.521,2.073 1.938,2.26 0.417,0.188 10 false SGN5 1.698,1.635 1.927,1.823 0.229,0.188 10 false VG 5.333,1.635 5.688,1.823 0.354,0.188 10 false VV- 5.333,1.188 5.688,1.375 0.354,0.188 10 false VV+ 5.333,0.688 5.781,0.875 0.448,0.188 10 false ADPG 1.563,0.667 1.979,0.854 0.417,0.188 10 false ADPI 1.698,1.177 1.906,1.365 0.208,0.188 10 false VD 5.375,2.594 5.708,2.781 0.333,0.188 10 false M38 1.969,0.583 2.156,0.771 0.188,0.188 10 false 18 1.979,1.094 2.156,1.281 0.177,0.188 10 false 24 1.979,1.542 2.156,1.729 0.177,0.188 10 false 25 5.177,1.542 5.292,1.729 0.115,0.188 10 false 6 5.177,1.083 5.292,1.271 0.115,0.188 10 false 5 5.177,0.563 5.292,0.75 0.115,0.188 10 false 8 1.979,1.979 2.156,2.167 0.177,0.188 10 false 23 3.344,1.865 3.927,2.052 0.583,0.188 10 false Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - VIDEO TERMINAL)
a.

Disconnect the Q21 television display assembly connector.


b.

Disconnect the M38 video terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q21-24 (VD) - M38-5 (VV+) Always Below 1 Ω
Q21-25 (VG) - M38-6 (VV-) Always Below 1 Ω
Q21-18 (ADPI) - M38-8 (ADPG) Always Below 1 Ω
Q21-24 (VD) - Body ground Always 10 kΩ or higher
Q21-25 (VG) - Body ground Always 10 kΩ or higher
Q21-18 (ADPI) - Body ground Always 10 kΩ or higher
Q21-23 (SGN5) - Body ground Always 10 kΩ or higher




OK

2.INSPECT VIDEO TERMINAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT VIDEO TERMINAL
a.

Reconnect the M38 video terminal connector.


b.
U189922E02
2.063,2.365 2.5,2.49 false 0.125,0.083 0.375,0.281 0.25,0.198 10 false *a 0.573,2.063 0.917,2.25 0.344,0.188 10 false M38 2.563,2.427 2.958,2.615 0.396,0.188 10 false VV+

Using an oscilloscope, check the signal waveform between terminal M38-5 (VV+) and body ground according to the conditions shown in the table below.

Standard Conditions:
Tester Connection Condition Specified Condition
M38-5 (VV+) - Body ground RSE system playing (VTR mode) Waveform synchronized with display signals is output


Text in Illustration
*a Component with harness connected
(Video Terminal)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG