Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY(for Manual Stowing Seat Type RH Side)
RM24M0E _58 Vehicle Interior _059567 SEAT _0291991 REAR NO. 2 SEAT ASSEMBLY(for Manual Stowing Seat Type RH Side) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Manual Stowing Seat Type RH Side)  REASSEMBLY  


PROCEDURE

Hide 71695E 1.INSTALL REAR NO. 2 SEAT PROTECTOR

a.
B148274

Install the 2 seat protectors.


b.
B148272E01
0.027,0.457 0.361,0.638 0.334,0.181 10 Tape 0.711,0.557 0.418,0.557 false 0.685,1.232 0.509,1.232 false 0.509,1.236 0.509,0.557 false 3.027,0.102 3.360,0.283 0.334,0.181 10 Tape 2.828,0.19 3.022,0.19 false 2.967,1.288 2.967,0.19 false 2.893,0.812 2.965,0.812 false 2.853,1.282 2.962,1.282 false

Apply new tape to the positions shown in the illustration.


Hide 72570C 2.INSTALL NO. 2 SEAT RECLINING ADJUSTING CABLE ASSEMBLY RH

a.
B137589E04
0.927,1.021 1.479,1.219 false 1.979,1.25 2.531,1.417 false 1.313,2.542 1.313,2.792 false 1.76,2.5 1.76,2.938 false 1.76,2.792 1.313,2.792 false 1.521,1.135 1.948,1.333 0.427,0.198 10 true White 1.552,2.938 1.927,3.115 0.375,0.177 10 false White

Install the 2 cables to the seatback as shown in the illustration.


b.
B148275

Clamp the cables to the seatback with 4 new cable ties as shown in the illustration.


c.
B137535E06
0.75,1.073 1.021,1.323 0.271,0.25 10 false Cut 0.906,4.031 1.615,4.208 0.708,0.177 10 false CORRECT 2.083,4.031 2.927,4.208 0.844,0.177 10 false INCORRECT 0.385,0.125 1.479,0.344 1.094,0.219 10 false 10 mm (0.40 in.)

Cut off the ends of the 4 cable ties as shown in the illustration.


d.

Attach the 4 clamps of the cable ties to the seatback.


Hide 72507D 3.INSTALL NO. 2 RECLINING RELEASE HANDLE SUB-ASSEMBLY

a.
B137592

Install the 2 nuts to install the handles.

HINT:

Pass the handles through the hole in the seatback frame toward the front of the vehicle.



Hide 79203A 4.INSTALL NO. 2 SEATBACK FRAME SUB-ASSEMBLY RH

a.
B141474E04
3.177,1.479 3.365,1.656 0.188,0.177 10 false (1) 3.208,1.875 3.396,2.052 0.188,0.177 10 false (2) 1.167,0.844 1.354,1.021 0.188,0.177 10 false (3) 1.313,0.604 1.5,0.781 0.188,0.177 10 false (4)

Temporarily install the seatback to the seat cushion with the 4 bolts.


b.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


c.

Connect the reclining adjusting cable to the seat cushion as shown in the illustration.


Hide 71694D 5.INSTALL REAR SEAT CUSHION HINGE COVER OUTER LH

a.
B135820

Install the hinge cover with the 2 screws.


Hide 71693C 6.INSTALL REAR SEAT CUSHION HINGE COVER OUTER RH

a.
B135819

Install the hinge cover with the 2 screws.


Hide 72552E 7.INSTALL RECLINING HINGE COVER LH

a.
B135833

Install the hinge cover with the screw.


Hide 72551E 8.INSTALL RECLINING HINGE COVER RH

a.
B460038

Attach the claw.


b.

Install the hinge cover with the screw.


Hide 79023 9.INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY RH

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.



a.

Fabric Seat (Low Grade)

i.

Using hog ring pliers, install the seatback cover to the seatback pad with 7 new hog rings.

B460073E01
2.375,2.573 2.198,2.167 false 0.344,3.427 1.083,3.688 0.74,0.26 10 false Hog Ring 2.25,2.604 3.438,2.885 1.188,0.281 10 false Hog Ring Pliers


ii.

Install the seatback cover (with pad) to the seatback frame.



b.

Fabric Seat (High Grade), Leather Seat

B460046E01
2.438,2.521 2.156,2.073 false 2.49,2.5 3.813,2.719 1.323,0.219 10 false Hog Ring Pliers 0.385,3.417 1.708,3.635 1.323,0.219 10 false Hog Ring

i.

Using hog ring pliers, install the seatback cover to the seatback pad with 13 new hog rings.


ii.

Install the seatback cover (with pad) to the seatback frame.



c.
B137588

Attach the 8 claws to install the 4 headrest supports.


d.
B140567

Install the handle with the nut.


e.
B135832

Install the center armrest with the 2 nuts.


f.
B141023E02
0.375,1.781 0.792,1.958 0.417,0.177 10 false Zipper

Close the zippers.


g.
B141444E02
2.021,1.917 1.688,1.635 false 0.375,4.219 0.969,4.396 0.594,0.177 10 false Hog Ring 2.063,1.854 3.042,2.031 0.979,0.177 10 false Hog Ring Pliers

Using hog ring pliers, install 5 new hog rings.


h.
B148137E02
0.385,4.302 0.729,4.479 0.344,0.177 10 false Hook 2.24,3.979 2.427,4.156 0.188,0.177 10 false (1) 2.604,2.104 2.792,2.281 0.188,0.177 10 false (2)

Attach each of the 3 hooks as shown in the illustration.


Hide 72679 10.INSTALL REAR SEATBACK LOCK CONTROL BEZEL

a.
B140916

Attach the claw to install the bezel.


b.

Install the 2 screws.


Hide 71940E 11.INSTALL NO. 2 SEAT HEADREST ASSEMBLY

Hide 71970 12.INSTALL REAR SEAT HEADREST ASSEMBLY

Hide 79021 13.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.



a.

Fabric Seat (Low Grade)

i.

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 18 new hog rings.

B460074E01
2.427,2.479 2.219,2.042 false 2.427,2.5 3.656,2.698 1.229,0.198 10 false Hog Ring Pliers 0.406,3.448 1.635,3.646 1.229,0.198 10 false Hog Ring


ii.

Install the seatback cover (with pad) to the seatback frame.



b.

Fabric Seat (High Grade), Leather Seat

i.

Close the fastening tape.

B460047E01
2.396,2.375 2.146,1.938 false 2.448,2.333 4.74,2.531 2.292,0.198 10 false Hog Ring Pliers 0.354,3.208 2.646,3.406 2.292,0.198 10 false Hog Ring 0.333,3.469 2.625,3.667 2.292,0.198 10 false Fastening Tape


ii.

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 17 new hog rings.


iii.

Install the seatback cover (with pad) to the seatback frame.



c.
B137134E01
0.354,1.806 0.695,1.987 0.341,0.181 10 Hook

Attach the hooks and install the seat cushion cover (with pad) to the seat cushion spring.


d.
B147486

Attach the 2 hooks.


e.

Attach the clip.


Hide 71324G 14.INSTALL REAR NO. 2 SEAT CUSHION

a.
B141418

Install the seat cushions with the screws.


Hide 71208A 15.INSTALL REAR SEAT CUSHION WIRE SUB-ASSEMBLY

a.
B142481

Install the cushion wire with the nut.


b.
B141420

Install the hinge cover with the screw.


Hide 71844A 19.INSTALL REAR NO. 2 SEAT RECLINING COVER LH

a.
B140805

Attach the 2 claws and seat cushion cover.


b.
B140796

Attach the 7 claws to install the cover.


c.

Install the 2 screws.


Hide 71843A 20.INSTALL REAR NO. 2 SEAT RECLINING COVER RH

a.
B135826

Attach the 8 claws to install the cover.


b.

Install the 2 screws.