Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type LH Side) › from 2016.05
RM24M0E _58 Vehicle Interior _059567 SEAT _0291992 REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type LH Side) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type LH Side)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the rear seat rear leg sub-assembly LH, rear seat cushion lock assembly LH and rear seat cushion lock assembly RH, make sure to remove only the rear seat rear leg sub-assembly LH and either rear seat cushion lock assembly first. Then reinstall the rear seat rear leg sub-assembly LH and rear seat cushion lock assembly before removing the other rear seat cushion lock assembly.


PROCEDURE

Hide 71844A 1.REMOVE REAR NO. 2 SEAT RECLINING COVER LH

a.
B148277E02
2.667,2.604 2.854,2.781 0.188,0.177 10 false (1) 2.667,3.917 2.854,4.094 0.188,0.177 10 false (2) 0.365,4.26 0.708,4.438 0.344,0.177 10 false Hook

Detach each of the 2 hooks as shown in the illustration.


b.
B138791

Remove the 2 screws.


c.

Using a screwdriver, detach the 8 claws and remove the cover.

HINT:

Tape the screwdriver tip before use.



Hide 71843A 2.REMOVE REAR NO. 2 SEAT RECLINING COVER RH

a.
B141403

Remove the 2 screws.


b.

Using a screwdriver, detach the 6 claws and remove the cover.

HINT:

Tape the screwdriver tip before use.



c.
B141404

Detach the 2 claws and cushion cover.


Hide 71940E 4.REMOVE NO. 2 SEAT HEADREST ASSEMBLY

Hide 79204A 5.REMOVE NO. 2 SEATBACK FRAME SUB-ASSEMBLY LH

a.
B147935E01
2.856,1.279 3.275,1.460 0.418,0.181 10 Clamp 0.318,1.417 0.737,1.598 0.418,0.181 10 Clamp 2.481,1.578 2.833,1.366 false 0.565,1.398 0.854,1.111 false

Disconnect the connector.


b.

Detach the 2 clamps.


c.
B138795

Remove the 4 bolts and seatback frame.


Hide 79024 6.REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY LH

a.
B138793E01
0.333,1.76 0.929,1.942 0.596,0.181 10 Hog Ring

Open the lower part of the No. 2 seatback cover sub-assembly LH and remove the 3 hog rings.


b.
B141395E01
0.378,1.843 0.791,2.025 0.413,0.181 10 Zipper

Open the 2 zippers.


c.
B141396

Detach the 4 claws and remove the 2 headrest supports.


d.

Remove the seatback cover (with pad) from the seat frame.


e.
B444134

for Type A:

i.

Remove the 2 hog rings and No. 2 seatback cover sub-assembly LH from the No. 2 seatback pad LH.



f.
B136993E02
0.32,1.759 0.916,1.940 0.596,0.181 10 Hog Ring 1.928,1.321 2.129,1.461 0.201,0.14

for Type B:

i.

Remove the 8 hog rings and No. 2 seatback cover sub-assembly LH from the No. 2 seatback pad LH.



Hide 72552B 7.REMOVE RECLINING HINGE COVER LH

a.
B138798

Remove the screw.


b.

Detach the claw and remove the hinge cover.


Hide 72551B 8.REMOVE RECLINING HINGE COVER RH

a.
B138799

Remove the screw and hinge cover.


Hide 82194 9.REMOVE REAR SEAT WIRE LH

a.
B142483E04
1.667,0.594 2.156,0.729 false 2.083,2.396 2.083,3.042 true 1.49,2.844 2.083,2.844 true 1.594,1.521 2.073,1.875 false 1.146,1.406 1.563,1.719 0.417,0.313 10 true Clamp 1.229,0.49 1.656,0.792 0.427,0.302 10 true Clamp 1.885,3.021 2.302,3.198 0.417,0.177 10 false Clamp

Disconnect the 4 connectors.


b.

Detach the 4 seat wire clamps from the seatback frame.


c.

Detach the clamp and remove the seat wire.


Hide 71695E 10.REMOVE FOLD SEAT PROTECTOR

a.
B138797E02
1.26,0.177 1.51,0.177 1.51,0.177 2.073,0.719 false 1.646,1.844 1.479,1.844 1.479,1.844 1.323,1.604 false 1.719,1.76 2.302,1.938 0.583,0.177 10 false Protector 0.135,0.083 1.26,0.26 1.125,0.177 10 false Seat Control ECU

Remove the 3 nuts and protector.


b.

Remove the seat control ECU.


Hide 71695E 11.REMOVE REAR NO. 2 SEAT PROTECTOR

a.
B148280E01
0.146,0.089 0.480,0.270 0.334,0.181 10 Tape 1.12,0.185 0.565,0.185 false 0.736,0.185 0.736,1.652 false 1.063,1.649 0.732,1.649 false

Remove the tape.


b.
B148281

Remove the seat protector.


Hide 72597 12.REMOVE RECLINING REMOTE CONTROL BEZEL

a.
B141406

Using a screwdriver, detach the 2 claws and remove the bezel.

HINT:

Tape the screwdriver tip before use.



Hide 79022 13.REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH

a.
B147937

Using a clip remover, remove the 2 clips.


b.
B147936E02
0.385,1.813 0.729,1.99 0.344,0.177 10 false Hook

Detach the hooks and remove the seat cushion cover (with pad) from the seat cushion spring.


c.
B444135

for Type A:

i.

Remove the 12 hog rings and No. 2 seat cushion cover sub-assembly LH from the No. 2 seat cushion pad LH.



d.
B444136E02
1.104,3.51 1.281,4.26 true 1.323,4.219 2.323,4.573 1,0.354 10 false Fastening Tape

for Type B:

i.

Remove the 12 hog rings.


ii.

Disengage the fastening tape and remove No. 2 seat cushion cover sub-assembly LH from the No. 2 seat cushion pad LH.



Hide 71694D 14.REMOVE REAR SEAT CUSHION HINGE COVER OUTER LH

a.
B141422

Remove the screw and hinge cover.


b.
B141423

Detach the 2 claws and remove the hinge cover.


Hide 71693C 15.REMOVE REAR SEAT CUSHION HINGE COVER OUTER RH

a.
B138802

Remove the screw and hinge cover.


Hide 84923 16.REMOVE POWER REAR SEAT SWITCH

a.
B141405

Remove the 2 screws.


b.

Disconnect the connector and remove the seat switch.


Hide 79621 17.REMOVE NO. 2 SEAT CUSHION STOPPER

a.
B138804

Remove the screw and cushion stopper.


Hide 71309C 18.REMOVE REAR SEAT REAR LEG SUB-ASSEMBLY LH

a.
B359113

Measure the distance between the points shown in the illustration.

NOTICE:

Make sure to measure this distance as the measured value will be used during reassembly.



b.
B357029

Using a screwdriver, remove the 2 E rings.


c.

Disconnect the cable from the No. 2 seat cushion spring assembly LH.


d.
B357030

Disconnect the 2 connectors.


e.
E282162

Disconnect the 3 connectors.


f.
E282164

Remove the 8 nuts.


g.
E282163

Apply battery voltage to the power seat motor assembly and move the rear seat rear leg sub-assembly LH until it stops at its most outward position.


h.

Insert a screwdriver with its tip wrapped with protective tape into the location shown in the illustration and detach the spring from the spring holder of the No. 2 seat cushion spring assembly LH.

B365118E03
1.771,0.354 2.271,0.917 false 2.094,1.417 2.51,1.708 false 2.115,2.927 2.438,3.115 false 0.771,0.271 1.833,0.458 1.063,0.188 10 false Protective Tape 2.073,1.708 3.135,1.896 1.063,0.188 10 false Spring Holder 2.031,3.115 3.094,3.302 1.063,0.188 10 false Spring Holder


i.

Apply battery voltage to the power seat motor assembly and move the rear seat rear leg sub-assembly LH 90° inward from the most outward position.

NOTICE:

If the rear seat rear leg sub-assembly LH is moved inward excessively, it cannot be removed from the No. 2 seat cushion spring assembly LH.


B365119E01
2.603,4.296 3.761,4.482 1.158,0.186 10 Spring Holder 4.294,4.296 5.452,4.482 1.158,0.186 10 Spring Holder 2.78,4.152 3.006,4.31 false 4.428,4.113 4.711,4.296 false 4.28,0.221 7.061,0.383 2.782,0.162 10 90° Inward From The Most Outward Position

HINT:

Moving the rear seat rear leg sub-assembly LH inward releases the spring from the spring holder, allowing the rear seat rear leg sub-assembly LH to be removed.



j.
E282167

Remove the rear seat rear leg sub-assembly LH from the No. 2 seat cushion spring assembly LH.


k.
B363684

Using a 5 mm hexagon socket wrench, remove the 4 bolts and power seat motor from the rear seat rear leg sub-assembly LH.


Hide 72680B 19.REMOVE REAR SEAT CUSHION LOCK ASSEMBLY LH

a.
B357729E01
1.967,3.085 2.171,2.515 2.171,2.515 2.337,2.515 false 1.738,3.725 1.967,3.085 false 1.879,3.658 2.081,3.096 2.081,3.096 1.978,3.063 false 2.359,2.439 3.093,2.641 0.735,0.202 10 Matchmark

Put matchmarks on the rear seat cushion lock assembly LH and washer.

NOTICE:

Make sure to put matchmarks on the rear seat cushion lock assembly LH and washer as they are necessary for reassembly.



b.
B357730

Remove the bolt, washer and nut.


c.
B360123

Slide the rear seat cushion lock assembly LH as shown in the illustration to remove it.


d.
B362825E02
0.594,4.292 1.573,4.51 0.979,0.219 10 false Clamp

Detach the clamp.


e.

Disconnect the connector.


f.
B362826

Detach the clamp and disconnect the cable.

NOTICE:

Make sure to remember the position and routing of the cable.



g.
B359076

Remove the bush from the rear seat cushion lock assembly LH.


Hide 72670B 20.REMOVE REAR SEAT CUSHION LOCK ASSEMBLY RH

a.
U188910E01
0.073,2.586 0.815,2.798 0.743,0.213 10 Matchmark 1.453,3.443 1.158,2.682 1.158,2.682 0.934,2.682 false 1.645,3.94 1.453,3.443 false 1.516,4.069 1.324,3.572 1.324,3.572 1.471,3.507 false

Put matchmarks on the rear seat cushion lock assembly RH and washer.

NOTICE:

Make sure to put matchmarks on the rear seat cushion lock assembly RH and washer as they are necessary for reassembly.



b.
B357735

Remove the bolt, washer and nut.


c.
B360124

Slide the rear seat cushion lock assembly RH as shown in the illustration to remove it.


d.
B362827E02
0.594,4.24 1.656,4.427 1.063,0.188 10 false Clamp

Detach the clamp.


e.

Disconnect the connector.


f.
B362828

Detach the clamp and disconnect the cable.

NOTICE:

Make sure to remember the position and routing of the cable.



g.
B359078

Remove the bush from the rear seat cushion lock assembly RH.