Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type LH Side) › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059567 SEAT _0291992 REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type LH Side) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type LH Side)  REASSEMBLY  


PROCEDURE

Hide 72670B 1.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY RH

a.
B359079

Install the bush to the rear seat cushion lock assembly RH.


b.
B365120E02
1.125,3.802 0.854,4.104 false 2.781,3.948 2.51,4.167 false 0.406,4.052 0.865,4.271 0.458,0.219 10 false Spring 2.073,4.063 2.531,4.281 0.458,0.219 10 false Spring

Set the rear seat cushion lock assembly RH to the No. 2 seat cushion spring assembly LH.

NOTICE:

Make sure that the spring is positioned as shown in the illustration.



c.
B357735

Temporarily install the rear seat cushion lock assembly RH with the bolt, washer and nut.


d.
U188910E01
0.073,2.586 0.815,2.798 0.743,0.213 10 Matchmark 1.453,3.443 1.158,2.682 1.158,2.682 0.934,2.682 false 1.645,3.94 1.453,3.443 false 1.516,4.069 1.324,3.572 1.324,3.572 1.471,3.507 false

Align the matchmarks and tighten the bolt to install the rear seat cushion lock assembly RH.

Torque:
15 N*m (149 kgf*cm, 11 ft.*lbf)


e.
B362829E02
0.625,4.208 1.406,4.438 0.781,0.229 10 false Clamp

Connect the connector.


f.

Attach the clamp.


g.
B362830

Install the cable to the No. 2 seat cushion spring assembly LH.


Hide 72680B 2.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY LH

a.
B359077

Install the bush to the rear seat cushion lock assembly LH.


b.
B365121E02
0.771,3.917 1.125,4.146 false 2.51,4.188 2.646,4.063 false 1.177,4.135 2.021,4.323 0.844,0.188 10 false Spring 2.063,4.115 2.906,4.302 0.844,0.188 10 false Spring

Set the rear seat cushion lock assembly LH to the No. 2 seat cushion spring assembly LH.

NOTICE:

Make sure that the spring is positioned as shown in the illustration.



c.
B357730

Temporarily install the rear seat cushion lock assembly LH with the bolt, washer and nut.


d.
B357729E01
1.967,3.085 2.171,2.515 2.171,2.515 2.337,2.515 false 1.738,3.725 1.967,3.085 false 1.879,3.658 2.081,3.096 2.081,3.096 1.978,3.063 false 2.359,2.439 3.093,2.641 0.735,0.202 10 Matchmark

Align the matchmarks and tighten the bolt to install the rear seat cushion lock assembly LH.

Torque:
15 N*m (149 kgf*cm, 11 ft.*lbf)


e.
B362831E01
0.541,4.26 1.528,4.431 0.987,0.172 10 Clamp

Connect the connector.


f.

Attach the clamp.


g.
B362832

Install the cable to the No. 2 seat cushion spring assembly LH.


Hide 71309C 3.INSTALL REAR SEAT REAR LEG SUB-ASSEMBLY LH

HINT:

The spring shown in the illustration is not installed on a rear seat rear leg sub-assembly LH supply part.


B363685E02
1.125,0.198 2.25,0.792 1.125,0.594 10 false Removed Part: 4.438,0.208 5.563,0.802 1.125,0.594 10 false Supply Part:

a.

With the rear seat rear leg sub-assembly LH in the most outward position, temporarily install the power seat motor assembly.

B363159E02
0.781,0.229 2.385,0.667 1.604,0.438 10 false Most Outward Position


b.
B363488

Using a 5 mm hexagon socket wrench, install the power seat motor assembly to the rear seat rear leg sub-assembly LH with the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 11 in.*lbf)


c.

Attach the spring to the spring holder.

B365122E02
1.813,1.25 2.156,1.563 true 1.802,2.833 2.188,3.198 true 1.802,1.552 2.948,1.906 1.146,0.354 10 false Spring Holder 1.76,3.25 2.906,3.604 1.146,0.354 10 false Spring Holder


d.
E282164

Install the rear seat rear leg sub-assembly LH to the No. 2 seat cushion spring assembly LH with the 8 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


e.
E282162

Install the 3 connectors.


f.

Adjust to the initial position.

i.

Measure the distance between the points shown in the illustration and check if the measured value is equal to the value measured during disassembly.

HINT:

If the measured values differ, perform the following adjustment procedure.

·

If the measured value is too large:

Apply battery voltage to the power seat motor assembly and move the rear seat rear leg sub-assembly LH inward.


·

If the measured value is too small:

Apply battery voltage to the power seat motor assembly and move the rear seat rear leg sub-assembly LH outward.



B363292E01
2.896,2.183 4.457,2.584 1.561,0.401 10 If the measured value is too small: 2.653,4.025 4.214,4.377 1.561,0.353 10 If the measured value is too large:



g.
B357032

Connect the 2 connectors.


h.
B357033

Connect the 2 cables to the No. 2 seat cushion spring assembly LH and install the 2 E rings.


Hide 79621 4.INSTALL NO. 2 SEAT CUSHION STOPPER

a.
B138804

Install the screw to install the cushion stopper.


Hide 84923 5.INSTALL POWER REAR SEAT SWITCH

a.
B141405

Connect the connector.


b.

Install the 2 screws to install the seat switch.


Hide 71693C 6.INSTALL REAR SEAT CUSHION HINGE COVER OUTER RH

a.
B138802

Install the 2 screws to install the hinge cover.


Hide 71694D 7.INSTALL REAR SEAT CUSHION HINGE COVER OUTER LH

a.
B141423

Attach the 2 claws to install the hinge cover.


b.
B141422

Install the screw to install the hinge cover.


Hide 79022 8.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.



a.

Close the fastening tape.


b.

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 12 new hog rings.

B460045E01
2.417,2.24 2.073,1.917 false 2.479,2.188 4.771,2.385 2.292,0.198 10 false Hog Ring Pliers 0.375,3.167 2.667,3.365 2.292,0.198 10 false Hog Ring 0.365,3.438 2.656,3.635 2.292,0.198 10 false Fastening Tape


c.
B147936E02
0.385,1.813 0.729,1.99 0.344,0.177 10 false Hook

Attach the hooks and install the seat cushion cover (with pad) to the seat cushion spring.


d.
B147937

Attach the 2 clips.


Hide 72597 9.INSTALL RECLINING REMOTE CONTROL BEZEL

a.
B141406

Attach the 2 claws to install the bezel.


Hide 71695E 10.INSTALL REAR NO. 2 SEAT PROTECTOR

a.
B148282

Install the seat protector.


b.
B148280E01
0.146,0.089 0.480,0.270 0.334,0.181 10 Tape 1.12,0.185 0.565,0.185 false 0.736,0.185 0.736,1.652 false 1.063,1.649 0.732,1.649 false

Apply new tape to the positions shown in the illustration.


Hide 71695E 11.INSTALL FOLD SEAT PROTECTOR

a.
B138797

Install the seat control ECU to the seatback frame.


b.

Install the 3 nuts to install the protector.


Hide 82194 12.INSTALL REAR SEAT WIRE LH

a.
B142483E05
1.667,0.594 2.156,0.729 false 2.083,2.385 2.083,3.031 true 1.49,2.844 2.083,2.844 true 1.625,1.583 2.073,1.885 false 1.198,1.438 1.615,1.74 0.417,0.302 10 true Clamp 1.135,0.49 1.552,0.667 0.417,0.177 10 true Clamp 1.875,3.021 2.292,3.198 0.417,0.177 10 false Clamp

Connect the 4 connectors.


b.

Attach the 4 seat wire clamps to the seatback frame.


Hide 72552B 13.INSTALL RECLINING HINGE COVER LH

a.
B138798

Attach the claw.


b.

Install the hinge cover with the screw.


Hide 72551B 14.INSTALL RECLINING HINGE COVER RH

a.
B138799

Install the hinge cover with the screw.


Hide 79022 15.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.



a.
B141388E03
1.979,3.781 2.156,3.906 0.177,0.125 2.052,2.198 1.708,1.854 false 0.396,4.25 0.99,4.427 0.594,0.177 10 false Hog Ring 2.115,2.146 3.094,2.323 0.979,0.177 10 false Hog Ring Pliers

Using hog ring pliers, install the seatback cover to the seatback pad with 8 new hog rings.


b.

Install the seatback cover (with pad) to the seatback frame.


c.
B141396

Attach the 4 claws to install the 2 headrest supports.


d.
B141395E01
0.378,1.843 0.791,2.025 0.413,0.181 10 Zipper

Close the zippers.


e.
B462630E01
0.354,1.823 1.146,2.031 0.792,0.208 10 false Hog Ring

Using hog ring pliers, install 3 new hog rings.


Hide 79204A 16.INSTALL NO. 2 SEATBACK FRAME SUB-ASSEMBLY LH

a.
B138795E01
0.731,0.955 0.917,1.137 0.187,0.181 10 (1) 0.547,1.368 0.734,1.549 0.187,0.181 10 (2) 2.232,1.826 2.419,2.007 0.187,0.181 10 (3) 2.679,1.603 2.865,1.784 0.187,0.181 10 (4)

Temporarily install the seatback to the seat cushion with the 4 bolts.


b.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 71940E 17.INSTALL NO. 2 SEAT HEADREST ASSEMBLY

Hide 71844A 18.INSTALL REAR NO. 2 SEAT RECLINING COVER LH

a.
B138791

Attach the 8 claws to install the cover.


b.

Install the 2 screws.


Hide 71843A 20.INSTALL REAR NO. 2 SEAT RECLINING COVER RH

a.
B141404

Attach the 2 claws and seat cushion cover.


b.
B141403

Attach the 6 claws to install the cover.


c.

Install the 2 screws.


d.
B148290E02
0.375,4.271 0.719,4.448 0.344,0.177 10 false Hook 2.24,3.99 2.427,4.167 0.188,0.177 10 false (1) 2.656,2.104 2.844,2.281 0.188,0.177 10 false (2)

Attach each of the 2 hooks as shown in the illustration.