Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type RH Side) › from 2016.05
RM24M0E _58 Vehicle Interior _059567 SEAT _0291993 REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type RH Side) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type RH Side)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the rear seat rear leg sub-assembly RH, rear seat cushion lock assembly LH and rear seat cushion lock assembly RH, make sure to remove only the rear seat rear leg sub-assembly RH and either rear seat cushion lock assembly first. Then reinstall the rear seat rear leg sub-assembly RH and rear seat cushion lock assembly before removing the other rear seat cushion lock assembly.


PROCEDURE

Hide 71844A 1.REMOVE REAR NO. 2 SEAT RECLINING COVER LH

a.
B148292E01
0.348,3.1 0.689,3.282 0.341,0.181 10 Hook 3.098,1.479 3.285,1.660 0.187,0.181 10 (1) 3.121,2.871 3.308,3.053 0.187,0.181 10 (2)

Detach each of the 3 hooks as shown in the illustration.


b.
B141537

Remove the 2 screws.


c.

Using a screwdriver, detach the 6 claws and remove the cover.

HINT:

Tape the screwdriver tip before use.



d.
B141538

Detach the 2 claws and cushion cover.


Hide 71843A 3.REMOVE REAR NO. 2 SEAT RECLINING COVER RH

a.
B141539

Remove the 2 screws.


b.

Using a screwdriver, detach the 8 claws and remove the cover.


Hide 71940E 4.REMOVE NO. 2 SEAT HEADREST ASSEMBLY

Hide 79203A 5.REMOVE NO. 2 SEATBACK FRAME SUB-ASSEMBLY RH

a.
B148294E01
0.203,2.863 0.621,3.044 0.418,0.181 10 Clamp 0.753,0.138 1.171,0.320 0.418,0.181 10 Clamp 0.772,2.474 0.48,2.858 false 1.282,0.257 1.998,0.578 false

Disconnect the connector.


b.

Detach the 2 clamps.


c.
B448877

Remove the 4 bolts and seatback frame.


Hide 71970 6.REMOVE REAR SEAT HEADREST ASSEMBLY

Hide 79023 7.REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY RH

a.
B444143

Open the lower part of the No. 2 seatback cover sub-assembly RH and remove the 4 hog rings.


b.
B141541E01
0.355,1.76 0.768,1.942 0.413,0.181 10 Zipper

Open the 2 zippers.


c.
B444144

Detach the 8 claws and remove the 4 headrest supports.


d.

Remove the seatback cover (with pad) from the seat frame.


e.
B444145

for Type A:

i.

Remove the 2 hog rings and No. 2 seatback cover sub-assembly RH from the No. 2 seatback pad RH.



f.
B444146

for Type B:

i.

Remove the 8 hog rings and No. 2 seatback cover sub-assembly RH from the No. 2 seatback pad RH.



Hide 72552E 8.REMOVE RECLINING HINGE COVER LH

a.
B139148

Remove the screw and hinge cover.


Hide 72551E 9.REMOVE RECLINING HINGE COVER RH

a.
B139149

Remove the screw.


b.

Detach the claw and remove the hinge cover.


Hide 82193 10.REMOVE REAR SEAT WIRE RH

a.
B139147E02
0.958,0.344 1.396,0.344 true 1.146,0.865 1.146,0.354 true 1.594,1.24 2.448,1.24 true 2.208,1.896 2.208,1.24 true 1.438,0.271 1.854,0.448 0.417,0.177 10 true Clamp 2.51,1.146 2.927,1.323 0.417,0.177 10 true Clamp

Disconnect the 4 connectors.


b.

Detach the 4 seat wire clamps from the seatback frame.


Hide 71696 11.REMOVE FOLD SEAT PROTECTOR

a.
B138797E02
1.26,0.177 1.51,0.177 1.51,0.177 2.073,0.719 false 1.646,1.844 1.479,1.844 1.479,1.844 1.323,1.604 false 1.719,1.76 2.302,1.938 0.583,0.177 10 false Protector 0.135,0.083 1.26,0.26 1.125,0.177 10 false Seat Control ECU

Remove the 3 nuts and protector.


b.

Remove the seat control ECU.


Hide 71695E 12.REMOVE REAR NO. 2 SEAT PROTECTOR

a.
B148299E01
3.001,0.156 3.334,0.337 0.334,0.181 10 Tape 2.696,0.252 2.997,0.252 false 2.898,0.252 2.898,1.326 false 2.9,1.326 2.709,1.326 false 2.762,0.851 2.893,0.851 false

Remove the tape.


b.
B148300

Remove the seat protector.


Hide 72597 15.REMOVE RECLINING REMOTE CONTROL BEZEL

a.
B141564

Using a screwdriver, detach the 2 claws and remove the bezel.


Hide 79021 16.REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH

a.
B147942

Using a clip remover, remove the 2 clips.


b.
B147943E02
0.385,1.865 0.729,2.042 0.344,0.177 10 false Hook

Using a screwdriver, detach the hooks and remove the seat cushion cover (with pad) from the seat cushion spring.


c.
B444147

for Type A:

i.

Remove the 15 hog rings and No. 2 seat cushion cover sub-assembly RH from the No. 2 seat cushion pad RH.



d.
B444148E02
0.948,3.26 0.948,4.104 false 0.49,4.135 1.479,4.469 0.99,0.333 10 false Fastening Tape

for Type B:

i.

Remove the 15 hog rings.


ii.

Disengage the fastening tape and remove the No. 2 seat cushion cover sub-assembly RH from the No. 2 seat cushion pad RH.



Hide 71694D 17.REMOVE REAR SEAT CUSHION HINGE COVER OUTER LH

a.
B139155

Remove the 2 screws and hinge cover.


Hide 71693C 18.REMOVE REAR SEAT CUSHION HINGE COVER OUTER RH

a.
B139154

Remove the screw and hinge cover.


b.
B141711

Disengage the 2 claws and remove the hinge cover.


Hide 84923 19.REMOVE POWER REAR SEAT SWITCH

a.
B139158

Remove the 2 screws.


b.

Disconnect the connector and remove the switch.


Hide 79621 20.REMOVE NO. 2 SEAT CUSHION STOPPER

a.
B139156

Remove the 2 screws and 2 cushion stoppers.


Hide 21.REMOVE REAR SEAT REAR LEG SUB-ASSEMBLY RH

a.
B359101

Measure the distance between the points shown in the illustration.

HINT:

Make sure to measure this distance as the measured value will be used during reassembly.



b.
E282023

Using a screwdriver, remove the 2 E rings.


c.

Disconnect the cable from the No. 2 seat cushion spring assembly RH.


d.
E282024

Disconnect the 2 connectors.


e.
E282025

Disconnect the 3 connectors.


f.
E282026

Remove the 8 nuts.


g.
E282027

Apply battery voltage to the power seat motor assembly and move the rear seat rear leg sub-assembly RH until it stops at its most outward position.


h.

Insert a screwdriver with its tip wrapped with protective tape into the location shown in the illustration and detach the spring from the spring holder of the No. 2 seat cushion spring assembly RH.

B365126E01
4.237,0.175 5.245,0.357 1.007,0.181 10 Protective Tape 5.685,1.688 6.560,1.844 0.874,0.157 10 Spring Holder 5.225,0.27 5.585,0.555 false 5.745,1.308 6.096,1.704 false 5.685,3.194 6.560,3.350 0.874,0.157 10 Spring Holder 5.746,2.833 6.104,3.214 false


i.

Apply battery voltage to the power seat motor assembly and move the rear seat rear leg sub-assembly RH 90° inward from the most outward position.

CAUTION:

If the rear seat rear leg sub-assembly RH is moved inward excessively, it cannot be removed from the No. 2 seat cushion spring assembly RH.


B365127E01
2.283,0.911 3.513,1.068 1.229,0.157 10 Spring Holder 3.537,0.953 4.766,1.110 1.229,0.157 10 Spring Holder 2.614,0.813 2.7,0.932 false 4.159,0.8 3.953,0.962 false 4.098,3.048 6.880,3.210 2.782,0.162 10 90° Inward From The Most Outward Position

HINT:

Moving the rear seat rear leg sub-assembly RH inward releases the spring from the spring holder, allowing the rear seat rear leg sub-assembly RH to be removed.



j.
E282032

Remove the rear seat rear leg sub-assembly RH from the No. 2 seat cushion spring assembly RH.


k.
B363682

Using a 5 mm hexagon socket wrench, remove the 4 bolts and power seat motor from the rear seat rear leg sub-assembly RH.


Hide 72680B 22.REMOVE REAR SEAT CUSHION LOCK ASSEMBLY LH

a.
B357698E01
2.3,2.14 3.010,2.296 0.710,0.157 10 Matchmark 1.721,3.56 2.063,2.231 2.063,2.231 2.249,2.231 false 1.568,3.65 1.704,3.12 1.704,3.12 1.834,3.12 false

Put matchmarks on the rear seat cushion lock assembly LH and washer.

NOTICE:

Make sure to put matchmarks on the rear seat cushion lock assembly LH and washer as they are necessary for reassembly.



b.
B357699

Remove the bolt, washer and nut.


c.
B361452

Slide the rear seat cushion lock assembly LH as shown in the illustration to remove it.


d.
B362833E01
0.616,4.228 1.036,4.385 0.421,0.157 10 Clamp

Detach the clamp.


e.

Disconnect the connector.


f.
B362834

Detach the clamp and disconnect the cable.

NOTICE:

Make sure to remember the position and routing of the cable.



g.
B359081

Remove the bush from the rear seat cushion lock assembly LH.


Hide 72670B 23.REMOVE REAR SEAT CUSHION LOCK ASSEMBLY RH

a.
B357703E01
0.039,2.331 0.749,2.488 0.710,0.157 10 Matchmark 1.525,3.937 1.135,2.423 1.135,2.423 0.949,2.423 false 1.704,3.842 1.509,3.084 1.509,3.084 1.305,3.084 false

Put matchmarks on the rear seat cushion lock assembly RH and washer.

NOTICE:

Make sure to put matchmarks on the rear seat cushion lock assembly RH and washer as they are necessary for reassembly.



b.
B357704

Remove the bolt, washer and nut.


c.
B361453

Slide the rear seat cushion lock assembly RH as shown in the illustration to remove it.


d.
B362835E01
0.593,4.177 1.013,4.333 0.421,0.157 10 Clamp

Detach the clamp.


e.

Disconnect the connector.


f.
B362836

Detach the clamp and disconnect the cable.

NOTICE:

Make sure to remember the position and routing of the cable.



g.
B359082

Remove the bush from the rear seat cushion lock assembly RH.