71695E
1.INSTALL REAR NO. 2 SEAT PROTECTOR
Install the 2 seat protectors.
Apply new tape to the positions shown in the illustration.
72570C
2.INSTALL NO. 2 SEAT RECLINING ADJUSTING CABLE ASSEMBLY RH
Install the 2 cables to the seatback as shown in the illustration.
Clamp the cables to the seatback with 4 new cable ties as shown in the illustration.
Cut off the ends of the 4 cable ties as shown in the illustration.
Attach the 4 clamps of the cable ties to the seatback.
72507D
3.INSTALL NO. 2 SEAT RECLINING RELEASE HANDLE SUB-ASSEMBLY
Install the 2 handles with the 2 nuts.
Pass the handles through the hole in the seatback frame toward the front of the vehicle.
79204A
4.INSTALL NO. 2 SEATBACK FRAME SUB-ASSEMBLY LH
Temporarily install the seatback to the seat cushion with the 4 bolts.
Tighten the 4 bolts in the order shown in the illustration.
Connect the reclining adjusting cable to the seat cushion as shown in the illustration.
71694D
5.INSTALL REAR SEAT CUSHION HINGE COVER OUTER LH
Attach the claw to install the hinge cover.
Install the 2 screws.
71693C
6.INSTALL REAR SEAT CUSHION HINGE COVER OUTER RH
Install the hinge cover with the 2 screws.
72552B
7.INSTALL RECLINING HINGE COVER LH
Attach the claw.
Install the hinge cover with the screw.
72551B
8.INSTALL RECLINING HINGE COVER RH
Install the hinge cover with the screw.
79024
9.INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Fabric Seat (Low Grade)
Using hog ring pliers, install the seatback cover to the seatback pad with 8 new hog rings.
Install the seatback cover (with pad) to the seatback frame.
Fabric Seat (High Grade), Leather Seat
Using hog ring pliers, install the seatback cover to the seatback pad with 8 new hog rings.
Install the seatback cover (with pad) to the seatback frame.
Attach the 4 claws to install the 2 headrest supports.
Install the handle with the nut.
Close the zippers.
Using hog ring pliers, install 3 new hog rings.
Attach each of the 2 hooks as shown in the illustration.
72679
10.INSTALL REAR SEATBACK LOCK CONTROL BEZEL
Attach the claw to install the bezel.
Install the 2 screws.
71940E
11.INSTALL NO. 2 SEAT HEADREST ASSEMBLY
71208A
12.INSTALL REAR SEAT CUSHION WIRE SUB-ASSEMBLY
Install the cushion wire with the nut.
Install the hinge cover with the screw.
79022
13.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Fabric Seat (Low Grade)
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 14 new hog rings.
Fabric Seat (High Grade), Leather Seat
Close the fastening tape.
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 13 new hog rings.
Attach the hooks and install the seat cushion cover (with pad) to the seat cushion spring.
Attach the 2 hooks.
71324G
14.INSTALL REAR NO. 2 SEAT CUSHION
Install the screw to install the seat cushion.
73590
15.INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH
71844A
16.INSTALL REAR NO. 2 SEAT RECLINING COVER LH
Attach the 8 claws to install the cover.
Install the 2 screws.
71843A
17.INSTALL REAR NO. 2 SEAT RECLINING COVER RH
Attach the 2 claws and seat cushion cover.
Attach the 7 claws to install the cover.
Install the 2 screws.