When the fold seat switch is operated, a switch operation signal is sent to the fold seat control ECU. The ECU receives switch operation signals from each switch and activates the folding motor, reclining motor, and release actuator.
Remove the fold seat control ECU with the connectors still connected.
Measure the voltage of the connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z3-14 (TBL) - Body ground | Fold seat switch OFF | 10 to 14 V |
| Z3-14 (TBL) - Body ground | Fold seat switch FOLDING
Back door OPEN |
Below 1 V |
| Z3-15 (RTRN) - Body ground | Fold seat switch OFF | 10 to 14 V |
| Z3-15 (RTRN) - Body ground | Fold seat switch RETURN
Back door OPEN |
Below 1 V |
| Z3-16 (FOLD) - Body ground | Fold seat switch OFF | 10 to 14 V |
| Z3-16 (FOLD) - Body ground | Fold seat switch STOWING
Back door OPEN |
Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Y3-14 (TBL) - Body ground | Fold seat switch OFF | 10 to 14 V |
| Y3-14 (TBL) - Body ground | Fold seat switch FOLDING
Back door OPEN |
Below 1 V |
| Y3-15 (RTRN) - Body ground | Fold seat switch OFF | 10 to 14 V |
| Y3-15 (RTRN) - Body ground | Fold seat switch RETURN
Back door OPEN |
Below 1 V |
| Y3-16 (FOLD) - Body ground | Fold seat switch OFF | 10 to 14 V |
| Y3-16 (FOLD) - Body ground | Fold seat switch STOWING
Back door OPEN |
Below 1 V |
NG
OK
Remove the fold seat switch.
Measure the resistance of the switch.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (FOLD) - 5 (E) | Fold seat switch STOWING | Below 30 Ω |
| 2 (RTRN) - 5 (E) | Fold seat switch RETURN | Below 30 Ω |
| 6 (TBL) - 5 (E) | Fold seat switch FOLDING | Below 30 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 10 (FOLD) - 5 (E) | Fold seat switch STOWING | Below 30 Ω |
| 8 (RTRN) - 5 (E) | Fold seat switch RETURN | Below 30 Ω |
| 3 (TBL) - 5 (E) | Fold seat switch FOLDING | Below 30 Ω |
OK
NG
Disconnect the P1 switch connector.
Disconnect the Z3*1 or Y3*2 ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| Z3-16 (FOLD) - P1-1 (FOLD) | Below 1 Ω |
| Z3-15 (RTRN) - P1-2 (RTRN) | Below 1 Ω |
| Z3-14 (TBL) - P1-6 (TBL) | Below 1 Ω |
| Z3-16 (FOLD) - Body ground | 10 kΩ or higher |
| Z3-15 (RTRN) - Body ground | 10 kΩ or higher |
| Z3-14 (TBL) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
|---|---|
| Y3-16 (FOLD) - P1-10 (FOLD) | Below 1 Ω |
| Y3-15 (RTRN) - P1-8 (RTRN) | Below 1 Ω |
| Y3-14 (TBL) - P1-3 (TBL) | Below 1 Ω |
| Y3-16 (FOLD) - Body ground | 10 kΩ or higher |
| Y3-15 (RTRN) - Body ground | 10 kΩ or higher |
| Y3-14 (TBL) - Body ground | 10 kΩ or higher |
OK
NG
Disconnect the S11*1 or S12*2 lock connector.
Measure the resistance of the switch.
*1: w/o Power back door
*2: w/ Power back door
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S12-3 (CTY) - S12-4 (E) | Back door OPEN | 10 kΩ or higher |
| S12-3 (CTY) - S12-4 (E) | Back door CLOSE | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S11-3 (D+) - S11-1 (ACT-) | Back door OPEN | 10 kΩ or higher |
| S11-3 (D+) - S11-1 (ACT-) | Back door CLOSE | Below 1 Ω |
OK
NG
Disconnect the P1 and S12*1 or S11*2 switch connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| P1-5 (E) - S12-3 (CTY) | Below 1 Ω |
| S12-4 (E) - Body ground | Below 1 Ω |
| P1-5 (E) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
|---|---|
| P1-5 (E) - S11-3 (D+) | Below 1 Ω |
| S11-1 (ACT-) - Body ground | Below 1 Ω |
| P1-5 (E) - Body ground | 10 kΩ or higher |
OK
NG