Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059567 SEAT _0291996 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Reclining Motor Circuit  


DESCRIPTION

The fold seat control ECU receives a switch operation signal from the power rear seat switch and the fold seat switch, and activates the reclining motor. At this time, the Hall IC (seatback position sensor) detects the actuation of the seatback and sends a seatback actuation signal to the fold seat control ECU. The fold seat control ECU uses signals from the Hall IC (seatback position sensor) to detect if an object is caught or if any other abnormal condition has occurred.

WIRING DIAGRAM

B142321E03
5.476,7.046 7.007,7.244 1.531,0.198 10 Fold Seat Control ECU 5.743,1.423 6.107,1.662 0.364,0.239 10 SV2 5.742,2.362 6.051,2.601 0.309,0.239 10 SG2 5.747,3.296 6.180,3.458 0.434,0.163 10 SRCL 5.341,1.423 5.547,1.595 0.206,0.172 10 Y3 5.349,2.362 5.559,2.534 0.210,0.173 10 Y3 5.349,3.3 5.559,3.461 0.210,0.160 10 Y3 5.349,4.799 5.559,4.980 0.210,0.181 10 Y2 5.353,5.738 5.577,5.897 0.224,0.158 10 Y2 5.362,1.194 5.583,1.391 0.221,0.198 10 25 5.35,2.109 5.580,2.302 0.230,0.193 10 36 5.355,3.048 5.659,3.250 0.304,0.202 10 22 5.4,4.568 5.588,4.756 0.188,0.188 10 2 5.401,5.523 5.571,5.693 0.170,0.170 10 6 5.742,4.79 6.176,5.020 0.434,0.230 10 RCL+ 5.747,5.724 6.153,5.956 0.406,0.232 10 RCL- 5.345,1.666 5.541,1.836 0.196,0.171 10 *2 5.345,2.604 5.527,2.763 0.182,0.158 10 *2 5.345,3.543 5.531,3.720 0.186,0.177 10 *2 5.345,5.042 5.531,5.226 0.186,0.183 10 *2 5.345,5.981 5.523,6.138 0.178,0.157 10 *2 4.929,1.423 5.134,1.586 0.206,0.163 10 Z3 4.936,2.362 5.142,2.534 0.206,0.173 10 Z3 4.936,3.3 5.129,3.479 0.192,0.178 10 Z3 4.933,4.799 5.125,4.957 0.192,0.157 10 Z2 4.936,5.738 5.147,5.897 0.210,0.158 10 Z2 4.942,1.194 5.162,1.391 0.221,0.198 10 25 4.93,2.109 5.159,2.302 0.230,0.193 10 36 4.934,3.048 5.238,3.250 0.304,0.202 10 22 4.979,4.568 5.168,4.756 0.188,0.188 10 2 4.981,5.523 5.151,5.693 0.170,0.170 10 6 4.925,1.666 5.107,1.841 0.182,0.175 10 *1 4.925,2.604 5.093,2.794 0.168,0.190 10 *1 4.925,3.543 5.079,3.707 0.155,0.164 10 *1 4.925,5.042 5.111,5.226 0.186,0.183 10 *1 4.925,5.981 5.093,6.138 0.168,0.157 10 *1 1.252,6.927 2.317,7.109 1.065,0.182 10 Reclining Motor 3.684,1.423 3.894,1.594 0.210,0.172 10 Y5 3.672,2.362 3.860,2.518 0.188,0.157 10 Y5 3.684,3.301 3.894,3.461 0.210,0.160 10 Y5 3.68,4.8 3.890,4.957 0.210,0.157 10 Y4 3.68,5.738 3.904,5.897 0.224,0.158 10 Y4 3.725,1.18 3.890,1.345 0.165,0.165 10 3 3.72,2.128 3.894,2.340 0.174,0.211 10 2 3.715,3.076 3.853,3.278 0.137,0.202 10 1 3.715,4.571 3.899,4.754 0.184,0.184 10 1 3.723,5.513 3.891,5.680 0.167,0.167 10 2 3.669,1.647 3.846,1.823 0.177,0.176 10 *2 3.669,2.586 3.850,2.762 0.182,0.177 10 *2 3.669,3.524 3.864,3.707 0.195,0.182 10 *2 3.669,5.024 3.864,5.194 0.195,0.170 10 *2 3.669,5.962 3.864,6.138 0.195,0.176 10 *2 3.27,1.423 3.462,1.594 0.192,0.172 10 Z5 3.27,2.362 3.462,2.505 0.192,0.143 10 Z5 3.27,3.301 3.493,3.458 0.224,0.158 10 Z5 3.266,4.8 3.458,4.957 0.192,0.157 10 Z4 3.262,5.738 3.472,5.907 0.210,0.169 10 Z4 3.318,1.18 3.483,1.345 0.165,0.165 10 3 3.314,2.128 3.488,2.340 0.174,0.211 10 2 3.309,3.076 3.446,3.278 0.137,0.202 10 1 3.309,4.571 3.493,4.754 0.184,0.184 10 1 3.317,5.513 3.485,5.680 0.167,0.167 10 2 3.262,1.647 3.432,1.805 0.170,0.158 10 *1 3.262,2.586 3.444,2.749 0.182,0.163 10 *1 3.262,3.524 3.439,3.707 0.177,0.182 10 *1 3.262,5.024 3.426,5.212 0.164,0.188 10 *1 3.262,5.962 3.426,6.138 0.164,0.176 10 *1 1.151,5.972 2.215,6.183 1.063,0.211 10 Reclining Motor 0.647,2.348 1.590,2.568 0.943,0.221 10 Hall IC Sensor 2.758,1.308 3.045,1.524 0.287,0.216 10 HLV 2.758,2.257 3.164,2.473 0.406,0.216 10 HLG 2.758,3.174 3.090,3.376 0.332,0.202 10 HLS 0.106,7.16 0.718,7.309 0.613,0.150 10 *1: for LH 0.106,7.454 0.755,7.600 0.649,0.146 10 *2: for RH 2.758,4.658 3.101,4.874 0.343,0.216 10 FWD 2.662,5.599 3.143,5.815 0.482,0.216 10 BACK

PROCEDURE

1.CHECK FOLD SEAT CONTROL ECU (RCL, SRCL, SV2 VOLTAGE)
a.
U188620E02
0.927,1.781 0.531,2.292 false 1.74,1.781 1.042,2.448 false 1.979,1.781 1.802,2.406 false 2.688,1.771 2.448,2.625 false 2.688,1.677 3.063,2.292 false 1.583,0.844 1.896,1 0.313,0.156 10 false Y3 1.01,0.833 1.281,0.979 0.271,0.146 10 false Z3 2.688,0.844 3,1 0.313,0.156 10 false Y2 2.25,0.854 2.521,1 0.271,0.146 10 false Z2 0.323,2.354 0.646,2.531 0.323,0.177 10 false SG2 0.844,2.458 1.146,2.635 0.302,0.177 10 false SV2 1.573,2.458 1.99,2.625 0.417,0.167 10 false SRCL 2.229,2.688 2.594,2.844 0.365,0.156 10 false RCL- 2.875,2.323 3.271,2.479 0.396,0.156 10 false RCL+ 2.458,0.635 2.646,0.802 0.188,0.167 10 false *1 2.958,0.635 3.156,0.875 0.198,0.24 10 false *2 0.24,2.771 0.854,2.979 0.615,0.208 10 false *1: for LH 0.24,3.052 0.885,3.24 0.646,0.188 10 false *2: for RH 1.198,0.635 1.438,0.833 0.24,0.198 10 false *1 1.792,0.635 1.99,0.875 0.198,0.24 10 false *2

Remove the fold seat control ECU with the connectors still connected.


b.

Measure the voltage of the connectors.

Standard voltage:
for LH:
Tester Connection Condition Specified Condition
Z2-2 (RCL+) - Z2-6 (RCL-) Power rear seat switch FORWARD
Back door OPEN
Lock switch UNLOCK
10 to 14 V
Z2-6 (RCL-) - Z2-2 (RCL+) Power rear seat switch BACKWARD
Back door OPEN
Lock switch UNLOCK
10 to 14 V
Z3-22 (SRCL) - Z3-36 (SG2) Motor is operating Below 1 V - 10 to 14 V
Pulse generation
Z3-25 (SV2) - Z3-36 (SG2) Back door OPEN 9 to 14 V

for RH:
Tester Connection Condition Specified Condition
Y2-2 (RCL+) - Y2-6 (RCL-) Power rear seat switch FORWARD
Back door OPEN
Lock switch UNLOCK
10 to 14 V
Y2-6 (RCL-) - Y2-2 (RCL+) Power rear seat switch BACKWARD
Back door OPEN
Lock switch UNLOCK
10 to 14 V
Y3-22 (SRCL) - Y3-36 (SG2) Motor is operating Below 1 V - 10 to 14 V
Pulse generation
Y3-25 (SV2) - Y3-36 (SG2) Back door OPEN 9 to 14 V




NG

2.CHECK WIRE HARNESS (FOLD SEAT CONTROL ECU - RECLINING MOTOR)

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK WIRE HARNESS (FOLD SEAT CONTROL ECU - RECLINING MOTOR)
U188826E02
0.844,1.958 0.604,2.49 false 1.563,1.948 1.208,2.552 false 1.781,1.948 1.646,2.542 false 2.448,1.958 2.208,2.51 false 2.438,1.865 2.75,2.531 false 6.021,1.875 6.021,2.396 false 4.01,1.885 3.781,2.156 false 4.188,1.875 4.5,2.167 false 6.229,1.865 6.688,2.396 false 5.813,1.875 5.219,2.375 false 0.198,0.063 1.833,0.25 1.635,0.188 10 false Wire Harness Side: 1.323,1.354 1.635,1.51 0.313,0.156 10 false Y3 0.792,1.365 1.063,1.51 0.271,0.146 10 false Z3 2.427,1.354 2.74,1.51 0.313,0.156 10 false Y2 2,1.354 2.271,1.5 0.271,0.146 10 false Z2 0.417,2.583 0.74,2.76 0.323,0.177 10 false SG2 1.052,2.583 1.354,2.76 0.302,0.177 10 false SV2 1.479,2.583 1.896,2.75 0.417,0.167 10 false SRCL 2.052,2.583 2.417,2.74 0.365,0.156 10 false RCL- 2.563,2.583 2.958,2.74 0.396,0.156 10 false RCL+ 2.208,1.281 2.396,1.448 0.188,0.167 10 false *1 2.635,1.281 2.833,1.521 0.198,0.24 10 false *2 0.073,3 0.781,3.208 0.708,0.208 10 false *1: for LH 0.073,3.333 0.708,3.521 0.635,0.188 10 false *2: for RH 0.875,0.365 2.354,0.552 1.479,0.188 10 false Fold Seat Control ECU 1,1.26 1.188,1.427 0.188,0.167 10 false *1 1.542,1.281 1.74,1.521 0.198,0.24 10 false *2 3.292,1.333 3.604,1.531 0.313,0.198 10 false Z4 3.302,1.781 3.656,1.979 0.354,0.198 10 false Y4 5.083,1.323 5.396,1.531 0.313,0.208 10 false Z5 5.083,1.781 5.427,1.969 0.344,0.188 10 false Y5 5.021,2.438 5.344,2.604 0.323,0.167 10 false HLS 5.875,2.438 6.177,2.604 0.302,0.167 10 false HLG 6.542,2.438 6.854,2.604 0.313,0.167 10 false HLV 4.958,0.333 5.99,0.542 1.031,0.208 10 false Reclining Motor 5.323,1.135 5.51,1.302 0.188,0.167 10 false *1 5.333,1.552 5.531,1.792 0.198,0.24 10 false *2 3.531,1.146 3.719,1.313 0.188,0.167 10 false *1 3.521,1.563 3.719,1.802 0.198,0.24 10 false *2 3.583,2.198 3.948,2.354 0.365,0.156 10 false FWD 4.302,2.198 4.74,2.375 0.438,0.177 10 false BACK

a.

Disconnect the Z2*1 and Z3*1, or Y2*2 and Y3*2 ECU connectors.


b.

Disconnect the Z4*1 and Z5*1, or Y4*2 and Y5*2 motor connectors.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LH:
Tester Connection Specified Condition
Z2-2 (RCL+) - Z4-1 (FWD) Below 1 Ω
Z2-6 (RCL-) - Z4-2 (BACK) Below 1 Ω
Z3-22 (SRCL) - Z5-1 (HLS) Below 1 Ω
Z3-25 (SV2) - Z5-3 (HLV) Below 1 Ω
Z3-36 (SG2) - Z5-2 (HLG) Below 1 Ω
Z2-2 (RCL+) - Body ground 10 kΩ or higher
Z2-6 (RCL-) - Body ground 10 kΩ or higher
Z3-22 (SRCL) - Body ground 10 kΩ or higher
Z3-25 (SV2) - Body ground 10 kΩ or higher
Z3-36 (SG2) - Body ground 10 kΩ or higher

for RH:
Tester Connection Specified Condition
Y2-2 (RCL+) - Y4-1 (FWD) Below 1 Ω
Y2-6 (RCL-) - Y4-2 (BACK) Below 1 Ω
Y3-22 (SRCL) - Y5-1 (HLS) Below 1 Ω
Y3-25 (SV2) - Y5-3 (HLV) Below 1 Ω
Y3-36 (SG2) - Y5-2 (HLG) Below 1 Ω
Y2-2 (RCL+) - Body ground 10 kΩ or higher
Y2-6 (RCL-) - Body ground 10 kΩ or higher
Y3-22 (SRCL) - Body ground 10 kΩ or higher
Y3-25 (SV2) - Body ground 10 kΩ or higher
Y3-36 (SG2) - Body ground 10 kΩ or higher




OK

3.INSPECT RECLINING MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RECLINING MOTOR
a.
U188749E02
1.708,1.771 1.708,2.531 false 1.99,1.771 2.427,2.448 false 2.365,2.49 2.719,2.646 0.354,0.156 10 false FWD 1.448,2.552 1.854,2.708 0.406,0.156 10 false BACK 0.438,1.292 0.625,1.448 0.188,0.156 10 false Z4 0.438,1.74 0.625,1.896 0.188,0.156 10 false Y4 0.698,1.104 0.865,1.26 0.167,0.156 10 false *1 0.708,1.625 0.875,1.781 0.167,0.156 10 false *2 0.229,2.635 0.885,2.844 0.656,0.208 10 false *1: for LH 0.229,2.969 0.885,3.177 0.656,0.208 10 false *2: for RH

Check if the motor rotates smoothly when the battery is connected to the reclining motor.

OK:
for LH:
Tester Connection Specified Condition
Battery positive (+) → Z4-1 (FWD)
Battery negative (-) → Z4-2 (BACK)
FORWARD
Battery positive (+) → Z4-2 (BACK)
Battery negative (-) → Z4-1 (FWD)
BACKWARD

for RH:
Tester Connection Specified Condition
Battery positive (+) → Y4-1 (FWD)
Battery negative (-) → Y4-2 (BACK)
FORWARD
Battery positive (+) → Y4-2 (BACK)
Battery negative (-) → Y4-1 (FWD)
BACKWARD




OK

REPLACE FOLD SEAT CONTROL ECU

NG

REPLACE RECLINING MOTOR