Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059567 SEAT _0291996 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Release Actuator Circuit  


DESCRIPTION

The fold seat control ECU receives a switch operation signal from the fold seat switch and activates the release actuator. The release actuator releases the lock of the stowed seat based on a drive voltage received from the ECU.

WIRING DIAGRAM

B142273E03
2.217,2.828 4.259,3.198 2.041,0.370 10 Rear No. 2 Seat Cushion Frame (Folding Motor) 2.554,1.938 2.700,2.112 0.147,0.174 10 E 2.604,2.231 3.713,2.368 1.110,0.137 10 Release Actuator 3.451,1.936 3.866,2.129 0.415,0.193 10 ACT 5.194,2.041 5.609,2.234 0.415,0.193 10 RACT 5.066,5.07 6.546,5.244 1.480,0.174 10 Fold Seat Control ECU 0.141,4.958 0.844,5.142 0.702,0.184 10 *1: for LH 0.141,5.267 0.772,5.466 0.631,0.199 10 *2: for RH 4.937,1.875 5.079,2.058 0.142,0.184 10 3 3.9,1.875 4.109,2.052 0.210,0.177 10 9 2.269,1.875 2.425,2.058 0.156,0.184 10 2 5.066,4.877 5.810,5.061 0.744,0.183 10 Z2*1, Y2*2 2.217,2.667 2.933,2.856 0.716,0.188 10 Z1*1, Y1*2

PROCEDURE

1.CHECK FOLD SEAT CONTROL ECU (RACT VOLTAGE)
a.
U188621E02
2.344,1.667 1.927,2.333 false 1.719,2.365 2.146,2.531 0.427,0.167 10 false RACT 2.688,0.854 3,1.01 0.313,0.156 10 false Y2 2.167,0.854 2.438,1 0.271,0.146 10 false Z2 2.344,0.667 2.531,0.833 0.188,0.167 10 false *1 2.906,0.667 3.104,0.906 0.198,0.24 10 false *2 0.333,2.563 0.958,2.771 0.625,0.208 10 false *1: for LH 0.333,2.917 1,3.104 0.667,0.188 10 false *2: for RH

Remove the fold seat control ECU with the connector still connected.


b.

Measure the voltage of the connector.

Standard voltage:
for LH:
Tester Connection Condition Specified Condition
Z2-3 (RACT) - Body ground Stowing/Return switch RETURN 10 to 14 V

for RH:
Tester Connection Condition Specified Condition
Y2-3 (RACT) - Body ground Stowing/Return switch RETURN 10 to 14 V




NG

2.CHECK WIRE HARNESS (FOLDING MOTOR - FOLD SEAT CONTROL ECU AND BODY GROUND)

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK WIRE HARNESS (FOLDING MOTOR - FOLD SEAT CONTROL ECU AND BODY GROUND)
a.

Disconnect the Z1*1 or Y1*2 motor connector.

B460076E01
0.5,0.917 0.833,1.167 0.333,0.25 0.5,1.25 0.833,1.5 0.333,0.25 5.667,1.25 6,1.5 0.333,0.25 6.25,1.25 6.583,1.5 0.333,0.25 1.146,2.104 1.427,1.51 false 2.427,1.49 2.75,1.49 false 5.563,2.26 5.969,1.74 false 0.094,0.073 1.427,0.281 1.333,0.208 10 false Wire Harness Side: 1.271,0.406 2.302,0.635 1.031,0.229 10 false Folding Motor 0.583,0.948 0.99,1.198 0.406,0.25 10 false Z1 0.875,0.927 1.281,1.177 0.406,0.25 10 false *1 0.583,1.281 0.99,1.531 0.406,0.25 10 false Y1 0.865,1.292 1.271,1.542 0.406,0.25 10 false *2 1.063,2.135 1.469,2.385 0.406,0.25 10 false E 2.792,1.406 3.198,1.656 0.406,0.25 10 false ACT 5.75,1.281 6.156,1.531 0.406,0.25 10 false Z2 6.333,1.281 6.74,1.531 0.406,0.25 10 false Y2 5.354,2.292 6.125,2.49 0.771,0.198 10 false RACT 4.417,2.479 5.083,2.792 0.667,0.313 10 false *2: for RH 4.698,0.198 6.365,0.479 1.667,0.281 10 false Fold Seat Control ECU 6.031,1.26 6.438,1.51 0.406,0.25 10 false *1 6.615,1.26 7.021,1.51 0.406,0.25 10 false *2 3.656,2.479 4.323,2.792 0.667,0.313 10 false *1: for LH


b.

Disconnect the Z2*1 or Y2*2 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LH
Tester Connection Specified Condition
Z2-3 (RACT) - Z1-9 (ACT) Below 1 Ω
Z1-2 (E) - Body ground Below 1 Ω
Z2-3 (RACT) - Body ground 10 kΩ or higher

for RH
Tester Connection Specified Condition
Y2-3 (RACT) - Y1-9 (ACT) Below 1 Ω
Y1-2 (E) - Body ground Below 1 Ω
Y2-3 (RACT) - Body ground 10 kΩ or higher




OK

REPLACE REAR NO. 2 SEAT CUSHION FRAME

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR