Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Manual Seat) › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059567 SEAT _0291998 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the front seat frame (with adjuster) may injure your hands.


HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 1.INSTALL SEAT TRACK ADJUSTING HANDLE

Hide 71537D 2.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

a.

Install the 2 protectors.


Hide 82192 3.INSTALL FRONT SEAT WIRE LH

a.

Engage each clamp to install the front seat wire LH.


Hide 71499B 4.INSTALL SEAT CUSHION SPRING DAMPER

a.
B206939

Install the seat cushion spring damper with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 71644 5.INSTALL ACTIVE HEADREST LOWER UNIT

a.
B462290E01
0.417,3.156 1.49,3.354 1.073,0.198 10 false : Clamp

Install the active headrest lower unit with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install the clamp.


Hide 71643A 6.INSTALL ACTIVE HEADREST UPPER UNIT

a.
B206911

Install the active headrest upper unit with the 4 nuts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


b.

Connect the cable to the active headrest upper unit with the nut as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 72477 7.INSTALL VERTICAL ADJUSTER SPACER

a.
B136506

Attach the claw to install the spacer.


Hide 71873 8.INSTALL FRONT SEAT CUSHION LOWER SHIELD RH

HINT:

Use the same procedures described for the LH side.


Hide 71874 9.INSTALL FRONT SEAT CUSHION LOWER SHIELD LH

a.
B136504

Attach the claw to install the lower shield.


Hide 71875E 10.INSTALL RECLINING ADJUSTER UPPER INSIDE COVER RH

a.

Install the inside cover with the screw.


Hide 71876B 11.INSTALL RECLINING ADJUSTER UPPER INSIDE COVER LH

a.
B136505

Install the inside cover with the screw.


Hide 71875B 12.INSTALL RECLINING ADJUSTER LOWER INSIDE COVER RH

a.

Attach the claw to install the inside cover.


b.

Install the screw.


Hide 71876A 13.INSTALL RECLINING ADJUSTER LOWER INSIDE COVER LH

a.
B136507

Attach the claw to install the inside cover.


b.

Install the screw.


c.

w/ Front Seat Side Airbag:

Attach the clamp to connect the wire harness of the side airbag.


Hide 71073S 14.INSTALL FRONT SEATBACK COVER

a.
B136511E03
1.75,3.146 2.583,3.146 false 1.708,1.51 1.708,0.25 1.708,0.25 2.177,0.25 false 0.479,4.313 1.083,4.563 0.604,0.25 10 false Hog Ring 2.625,2.99 3.292,3.365 0.667,0.375 10 false Fastening Tape 2.24,0.156 3.24,0.385 1,0.229 10 false Hog Ring Pliers

for High Grade:

Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings and close the fastening tape.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.
B206951E03
2.677,2.708 1.781,2.115 true 0.552,2.958 1.229,3.24 0.677,0.281 10 false Hog Ring 2.719,2.604 3.354,3.156 0.635,0.552 10 false Fastening Tape

for Leather Seat:

Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings and close the fastening tape.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




c.
B141759E02
1.75,1.49 1.75,0.24 1.75,0.24 2.167,0.24 false 0.49,4.313 1.115,4.583 0.625,0.271 10 false Hog Ring 2.24,0.135 3.229,0.344 0.99,0.208 10 false Hog Ring Pliers

for Low Grade:

Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.


d.
B136512E02
0.76,0.99 0.615,1.188 false 1.521,2.031 1.135,1.969 false 1.927,0.125 1.74,0.125 false 1.74,0.125 0.979,0.365 false 1.74,0.125 1.74,1.313 false 0.438,1.188 0.781,1.406 0.344,0.219 10 false Hole 0.719,1.865 1.063,2.063 0.344,0.198 10 false Hole 1.979,0.042 3.125,0.25 1.146,0.208 10 true Fastening Rubber

Pass the fastening rubber through the hole in the seatback pad.


e.

Install the seatback cover (with pad) to the front seat frame with adjuster.


f.
B060977

Attach the 4 claws to install the 2 headrest supports.


g.
B338641E02
0.427,1.844 1.042,2.094 0.615,0.25 10 true Hog Ring

Using hog ring pliers, install new hog rings on the upper part of the seatback cover (with pad).


h.
B131236

w/ Front Seat Side Airbag:

Fully cover the airbag with the 2 seatback cover brackets and install the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

CAUTION:
·

For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.

·

Make sure that the strap is not twisted after installing the bracket.

·

Install the bracket securely.




i.
B141715E05
1.292,0.771 1.656,1.313 false 0.521,1.854 1.156,2.115 0.635,0.26 10 false Hog Ring 1.219,1.344 2.375,1.521 1.156,0.177 10 false Fastening Rubber

Attach the fastening rubbers with new hog rings as shown in the illustration.


j.
B206949E02
0.521,1.771 1.177,2.031 0.656,0.26 10 true Hog Ring

Using hog ring pliers, install new hog rings on the lower part of the seatback cover (with pad).


Hide 71072S 15.INSTALL FRONT SEAT CUSHION COVER

B136515E02
1.708,1.552 1.708,0.281 1.708,0.281 2.167,0.281 false 0.521,4.323 1.229,4.563 0.708,0.24 10 false Hog Ring 2.25,0.177 3.26,0.469 1.01,0.292 10 false Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.



a.

for High Grade:

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.


b.
B141757E03
1.698,1.542 1.854,0.354 1.854,0.354 2.052,0.354 false 0.521,4.302 1.125,4.573 0.604,0.271 10 false Hog Ring 2.125,0.281 3.146,0.531 1.021,0.25 10 false Hog Ring Pliers

for Low Grade:

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.


c.

Install the seat cushion cover (with pad) to the front seat frame with adjuster.


d.
B136517

Attach the 2 hooks on the seat cushion front side.


e.
B136513E02
0.313,1 0.313,1.177 false 3.083,0.99 3.083,1.156 false 0.802,1.625 0.51,2.677 false 0.51,2.677 0.875,2.427 false 2.667,1.688 2.865,1.688 false 1.896,1.073 2.646,0.292 false 2.646,0.292 2.823,0.292 false 2.375,1.073 2.635,0.292 false 1.083,1.031 0.917,0.354 false 0.917,0.344 0.656,0.344 false 0.198,1.198 0.583,1.385 0.385,0.188 10 false Clip 2.969,1.177 3.354,1.365 0.385,0.188 10 false Clip 0.271,2.698 0.667,2.917 0.396,0.219 10 false Hook 2.906,1.604 3.302,1.823 0.396,0.219 10 false Hook 2.865,0.219 3.26,0.438 0.396,0.219 10 false Hook 0.313,0.25 0.708,0.469 0.396,0.219 10 false Hook

Attach the hooks and install the 2 clips.


f.

w/ Seat Heater System:

Connect the connector.


Hide 72880A 16.INSTALL FRONT SEAT INNER ARMREST ASSEMBLY LH

a.
B136519

Install the armrest with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 72878 17.INSTALL SEAT ARMREST COVER LH

a.
B136518

Attach the 3 claws to install the armrest cover.


Hide 73240 18.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

Hide 71862 19.INSTALL FRONT SEAT CUSHION INNER SHIELD LH

a.
B136529

Attach the clip and 2 claws to install the inner shield.


b.

Install the screw.


Hide 71811D 20.INSTALL FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)

a.
B136528

Attach the clip and 2 claws to install the cushion shield.


b.

Install the screw.


c.
B136522

Connect the 2 rubber bands of the front seatback cover to the front seat frame with adjuster.


Hide 71812D 21.INSTALL FRONT SEAT CUSHION SHIELD LH (for Driver Side)

a.
B136527

Attach the clip and 2 claws to install the cushion shield.


b.

Install the screw.


c.
B136522

Connect the 2 rubber bands of the front seatback cover to the front seat frame with adjuster.


Hide 72525A 22.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH (for Front Passenger Side)

HINT:

Use the same procedures described for the driver side.


Hide 72526A 23.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH (for Driver Side)

a.
B141779E01
0.651,1.658 1.009,1.798 0.358,0.140 10 Claw 0.61,0.779 0.8,1.653 false

Attach the claw to install the release handle.


Hide 72457D 24.INSTALL VERTICAL SEAT ADJUSTER KNOB LH (for Driver Side)

a.
B136521

Install the snap ring to the knob as shown in the illustration.


b.

Install the knob (with snap ring) to the front seat frame with adjuster.


Hide 72493 25.INSTALL NO. 2 VERTICAL ADJUSTING HANDLE (for Driver Side)

a.
B136525

Install the handle with the 2 screws.


Hide 72459A 26.INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)

a.
B136524

Attach the 3 claws to install the cap.


Hide 71139L 27.INSTALL FRONT SEAT LEG COVER

a.

Install the 2 leg covers.


Hide 72143A 28.INSTALL FRONT SEAT TRACK BRACKET

a.
B136535

Install the 2 brackets with the 4 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 71140 29.INSTALL FRONT SEAT LEG ASSEMBLY LH

a.
B141473

Install the seat leg with the 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)