Wear protective gloves. Sharp areas on the front seat frame with adjuster may injure your hands.
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
71537D
1.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
82192
2.INSTALL FRONT SEAT WIRE LH
71499B
3.INSTALL SEAT CUSHION SPRING DAMPER
Install the seat cushion spring damper with the 2 nuts.
71644
4.INSTALL ACTIVE HEADREST LOWER UNIT
Install the active headrest lower unit with the 2 nuts.
Install the clamp.
71643A
5.INSTALL ACTIVE HEADREST UPPER UNIT
Install the active headrest upper unit with the 4 nuts.
Connect the cable to the active headrest upper unit with the nut as shown in the illustration.
71873
6.INSTALL FRONT SEAT CUSHION LOWER SHIELD RH
Use the same procedures described for the LH side.
71874
7.INSTALL FRONT SEAT CUSHION LOWER SHIELD LH
Attach the hook of the lower shield.
Install the lower shield with the screw.
71875B
8.INSTALL RECLINING ADJUSTER UPPER INSIDE COVER RH
Use the same procedures described for the LH side.
71876A
9.INSTALL RECLINING ADJUSTER UPPER INSIDE COVER LH
Install the inside cover with the screw.
71875A
10.INSTALL RECLINING ADJUSTER LOWER INSIDE COVER RH
Attach the claw to install the inside cover.
Install the 2 screws.
71875G
11.INSTALL RECLINING ADJUSTER LOWER INSIDE COVER LH
Attach the claw to install the inside cover.
Install the 2 screws.
w/ Front Seat Side Airbag:
Attach the clamp to connect the wire harness of the side airbag.
71074S
12.INSTALL FRONT SEATBACK COVER
except Leather Seat:
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings and close the fastening tape.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
for Leather Seat:
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings and close the fastening tape.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Pass the fastening rubber through the hole in the seatback pad.
Install the seatback cover (with pad) to the front seat frame with adjuster.
Attach the 4 claws to install the 2 headrest supports.
Using hog ring pliers, install new hog rings on the upper part of the seatback cover (with pad).
w/ Front Seat Side Airbag:
Fully cover the airbag with the 2 seatback cover brackets and install the nut.
For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
Make sure that the strap is not twisted after installing the bracket.
Install the bracket securely.
Attach the fastening rubbers with new hog rings as shown in the illustration.
Using hog ring pliers, install new hog rings on the lower part of the seatback cover (with pad).
Install the 2 front seatback pocket clips.
71072S
13.INSTALL FRONT SEAT CUSHION COVER
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
Install the seat cushion cover (with pad) to the front seat frame with adjuster.
Attach the 2 hooks on the seat cushion front side.
Attach the hooks and install the 2 clips.
w/ Seat Heater System:
Connect the connector.
72880A
14.INSTALL FRONT SEAT INNER ARMREST ASSEMBLY LH
Install the armrest with the bolt.
72878
15.INSTALL SEAT ARMREST COVER LH
Attach the 3 claws to install the armrest cover.
84922
16.INSTALL FRONT POWER SEAT SWITCH
Connect the connector.
Install the switch with the 3 screws.
73240
17.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
71862
18.INSTALL FRONT SEAT CUSHION INNER SHIELD LH
Attach the claw and install the inner shield to the front seat cushion shield.
Install the screw.
71812D
19.INSTALL FRONT SEAT CUSHION SHIELD LH
Attach the claw and install the outer shield to the front seat cushion shield (with front seat cushion inner shield).
Install the screw.
Install the front seat cushion shield (with front seat cushion inner shield and front seat cushion outer shield) in the direction indicated by the arrow in the illustration.
for LH side:
Attach the claw and clip.
for RH side:
Attach the 3 claws and clip.
for LH side:
Install the 3 screws.
for RH side:
Install the 2 screws.
Install the 2 screws on the backside of the seat cushion.
Connect the 2 rubber bands of the front seatback cover to the front seat frame with adjuster.
84921B
20.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Attach the knob.
84921A
21.INSTALL RECLINING POWER SEAT SWITCH KNOB
Attach the knob.
71139L
22.INSTALL FRONT SEAT LEG COVER
Install the 2 leg covers.
72143A
23.INSTALL FRONT SEAT TRACK BRACKET
Install the 2 brackets with the 4 nuts.
71140
24.INSTALL FRONT SEAT LEG ASSEMBLY LH
Install the seat leg with the 2 nuts.