Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Power Seat) › from 2016.05
RM24M0E _58 Vehicle Interior _059567 SEAT _0291999 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the front seat frame with adjuster may injure your hands.


HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 71537D 1.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

Hide 82192 2.INSTALL FRONT SEAT WIRE LH

Hide 71499B 3.INSTALL SEAT CUSHION SPRING DAMPER

a.
B206939

Install the seat cushion spring damper with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 71644 4.INSTALL ACTIVE HEADREST LOWER UNIT

a.
B462290E01
0.417,3.156 1.49,3.354 1.073,0.198 10 false : Clamp

Install the active headrest lower unit with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install the clamp.


Hide 71643A 5.INSTALL ACTIVE HEADREST UPPER UNIT

a.
B206911

Install the active headrest upper unit with the 4 nuts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


b.

Connect the cable to the active headrest upper unit with the nut as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 71873 6.INSTALL FRONT SEAT CUSHION LOWER SHIELD RH

HINT:

Use the same procedures described for the LH side.


Hide 71874 7.INSTALL FRONT SEAT CUSHION LOWER SHIELD LH

a.
B141953

Attach the hook of the lower shield.


b.

Install the lower shield with the screw.


Hide 71875B 8.INSTALL RECLINING ADJUSTER UPPER INSIDE COVER RH

HINT:

Use the same procedures described for the LH side.


Hide 71876A 9.INSTALL RECLINING ADJUSTER UPPER INSIDE COVER LH

a.
B141952

Install the inside cover with the screw.


Hide 71875A 10.INSTALL RECLINING ADJUSTER LOWER INSIDE COVER RH

a.

Attach the claw to install the inside cover.


b.

Install the 2 screws.


Hide 71875G 11.INSTALL RECLINING ADJUSTER LOWER INSIDE COVER LH

a.
B141951

Attach the claw to install the inside cover.


b.

Install the 2 screws.


c.

w/ Front Seat Side Airbag:

Attach the clamp to connect the wire harness of the side airbag.


Hide 71074S 12.INSTALL FRONT SEATBACK COVER

a.
B141759E02
1.75,1.49 1.75,0.24 1.75,0.24 2.167,0.24 false 0.49,4.313 1.115,4.583 0.625,0.271 10 false Hog Ring 2.24,0.135 3.229,0.344 0.99,0.208 10 false Hog Ring Pliers

for Type A:

i.

Using hog ring pliers, install the front seatback cover to the front seatback pad with 4 new hog rings.

NOTICE:
·

Be careful not to damage the front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seatback cover.





b.

for Type B:

i.
B136511E03
1.75,3.146 2.583,3.146 false 1.708,1.51 1.708,0.25 1.708,0.25 2.177,0.25 false 0.479,4.313 1.083,4.563 0.604,0.25 10 false Hog Ring 2.625,2.99 3.292,3.365 0.667,0.375 10 false Fastening Tape 2.24,0.156 3.24,0.385 1,0.229 10 false Hog Ring Pliers

w/o Seat Heater System:

1.

Engage the fastening tape.

2.

Using hog ring pliers, install the front seatback cover to the front seatback pad with 2 new hog rings.


NOTICE:
·

Be careful not to damage the front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seatback cover.




ii.
B448869E01
2.631,3.051 3.273,3.748 0.642,0.698 10 Fastening Tape 1.756,2.788 2.614,3.145 false

w/ Seat Heater System:

1.

Engage the fastening tape.

2.

Using hog ring pliers, install the front seatback cover to the front seatback pad with 4 new hog rings.


NOTICE:
·

Be careful not to damage the front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seatback cover.





c.
B136512E02
0.76,0.99 0.615,1.188 false 1.521,2.031 1.135,1.969 false 1.927,0.125 1.74,0.125 false 1.74,0.125 0.979,0.365 false 1.74,0.125 1.74,1.313 false 0.438,1.188 0.781,1.406 0.344,0.219 10 false Hole 0.719,1.865 1.063,2.063 0.344,0.198 10 false Hole 1.979,0.042 3.125,0.25 1.146,0.208 10 true Fastening Rubber

Pass the fastening rubber through the hole in the seatback pad.


d.

Install the seatback cover (with pad) to the front seat frame with adjuster.


e.
B060977

Attach the 4 claws to install the 2 headrest supports.


f.
B444117

Using hog ring pliers, install 3 new hog rings on the upper part of the front seatback cover (with pad).

NOTICE:
·

Be careful not to damage the front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seatback cover.




g.
B131236

w/ Front Seat Side Airbag:

Fully cover the airbag with the 2 seatback cover brackets and install the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

CAUTION:
·

For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.

·

Make sure that the strap is not twisted after installing the bracket.

·

Install the bracket securely.




h.
B141715E05
1.292,0.771 1.656,1.313 false 0.521,1.854 1.156,2.115 0.635,0.26 10 false Hog Ring 1.219,1.344 2.375,1.521 1.156,0.177 10 false Fastening Rubber

Engage the fastening rubbers with 3 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seatback cover.




i.
B206949E02
0.521,1.771 1.177,2.031 0.656,0.26 10 true Hog Ring

Using hog ring pliers, install 5 new hog rings on the lower part of the front seatback cover (with pad).

NOTICE:
·

Be careful not to damage the front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seatback cover.




j.

Install the 2 front seatback pocket clips.


Hide 71072S 13.INSTALL FRONT SEAT CUSHION COVER

a.
B444118

for Type A

i.

Using hog ring pliers, install the front seat cushion cover to the front seat cushion pad with 14 new hog rings.

NOTICE:
·

Be careful not to damage the front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seat cushion cover.





b.
B136515E02
1.708,1.552 1.708,0.281 1.708,0.281 2.167,0.281 false 0.521,4.323 1.229,4.563 0.708,0.24 10 false Hog Ring 2.25,0.177 3.26,0.469 1.01,0.292 10 false Hog Ring Pliers

for Type B:

i.

Using hog ring pliers, install the front seat cushion cover to the front seat cushion pad with 16 new hog rings.

NOTICE:
·

Be careful not to damage the front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seat cushion cover.





c.

Install the seat cushion cover (with pad) to the front seat frame with adjuster.


d.
B141950

Attach the 2 hooks on the seat cushion front side.


e.
B141948

Attach the hooks and install the 2 clips.


f.

w/ Seat Heater System:

Connect the connector.


Hide 72880A 14.INSTALL FRONT SEAT INNER ARMREST ASSEMBLY LH

a.
B136519

Install the front seat inner armrest assembly LH with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 72878 15.INSTALL SEAT ARMREST COVER LH

a.
B136518

Attach the 3 claws to install the armrest cover.


Hide 84922 16.INSTALL FRONT POWER SEAT SWITCH

a.

Connect the connector.


b.
B141947

Install the switch with the 3 screws.


Hide 73240 17.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

Hide 71862 18.INSTALL FRONT SEAT CUSHION INNER SHIELD LH

a.
B141943

Attach the claw and install the inner shield to the front seat cushion shield.


b.

Install the screw.


Hide 71812D 19.INSTALL FRONT SEAT CUSHION SHIELD LH

a.
B141944

Attach the claw and install the outer shield to the front seat cushion shield (with front seat cushion inner shield).


b.

Install the screw.


c.
B141942

Install the front seat cushion shield (with front seat cushion inner shield and front seat cushion outer shield) in the direction indicated by the arrow in the illustration.


d.
B148607

for LH side:

Attach the claw and clip.


e.
B148606

for RH side:

Attach the 3 claws and clip.


f.
B148605

for LH side:

Install the 3 screws.


g.
B148604

for RH side:

Install the 2 screws.


h.
B141938

Install the 2 screws on the backside of the seat cushion.


i.
B141937

Connect the 2 rubber bands of the front seatback cover to the front seat frame with adjuster.


Hide 84921B 20.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

a.
B141905

Attach the knob.


Hide 84921A 21.INSTALL RECLINING POWER SEAT SWITCH KNOB

a.
B141904

Attach the knob.


Hide 71139L 22.INSTALL FRONT SEAT LEG COVER

a.

Install the 2 leg covers.


Hide 72143A 23.INSTALL FRONT SEAT TRACK BRACKET

a.
B141900

Install the 2 brackets with the 4 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 71140 24.INSTALL FRONT SEAT LEG ASSEMBLY LH

a.
B141901

Install the seat leg with the 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)