71848B
1.REMOVE SEAT ADJUSTER COVER CAP RH
Using a screwdriver, detach the claw and remove the cap.
Tape the screwdriver tip before use.
73350A
2.REMOVE REAR NO. 1 SEAT LAP TYPE BELT ASSEMBLY CENTER
71834A
3.REMOVE REAR NO. 1 SEAT RECLINING COVER LH
Remove the 2 screws.
Using a screwdriver, detach the 6 claws and remove the reclining cover.
Tape the screwdriver tip before use.
72525C
4.REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH
Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the handle.
Tape the screwdriver tip before use.
72215
5.REMOVE SEAT TRACK HANDLE CONTROL LEVER RH
Raise the seat track handle control lever to reveal the claw. Using a screwdriver, detach the claw and remove the handle.
Tape the screwdriver tip before use.
71833A
6.REMOVE REAR NO. 1 SEAT RECLINING COVER RH
Remove the 2 screws.
Using a screwdriver, detach the 7 claws and remove the reclining cover.
Tape the screwdriver tip before use.
71867K
7.REMOVE REAR SEAT CUSHION SHIELD LH (for RH Side)
Remove the screw.
Detach the 2 claws and remove the cushion shield LH.
71873C
8.REMOVE REAR SEAT CUSHION SHIELD LOWER RH
Remove the screw.
Detach the claw and remove the cushion shield lower.
9.REMOVE REAR SEAT CUSHION ASSEMBLY RH
for LH Side:
Remove the bolt and bush.
for RH Side:
Remove the 3 bolts.
Remove the seat cushion.
71868J
10.REMOVE REAR SEAT CUSHION SHIELD RH (for LH Side)
Remove the screw.
Detach the 3 claws and remove the cushion shield LH.
72927
11.REMOVE REAR SEAT CUSHION UNDER COVER RH
Remove the 4 screws and 2 cushions.
Remove the seat cushion under cover.
72615C
12.REMOVE REAR SEAT BACK LOCK STRIKER COVER
Using a screwdriver, detach the 3 claws and remove the cover.
Tape the screwdriver tip before use.
73315
13.REMOVE REAR SEAT BELT COVER INNER RH
Remove the 4 screws.
Remove the seat belt cover.
73310
14.DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
73375
15.REMOVE REAR SEAT SHOULDER BELT HOLE COVER LH
Using a screwdriver, detach the 4 claws and remove the cover.
Tape the screwdriver tip before use.
71877B
16.REMOVE REAR SEAT ARMREST HOLE COVER RH
Using a screwdriver, detach the 2 claws and remove the armrest hole cover.
Tape the screwdriver tip before use.
72830J
17.REMOVE REAR NO. 1 SEAT ARMREST ASSEMBLY RH
Remove the bolt and armrest.
18.REMOVE CENTER ARMREST ASSEMBLY
Remove the 5 hog rings.
Open the fastener on the left side and turn up the seatback cover.
Remove the 2 nuts and armrest.
71349C
19.REMOVE REAR SEATBACK HINGE COVER
Remove the bolt.
Remove the seatback hinge cover.
71281A
20.REMOVE REAR SEAT CENTER ARMREST HINGE
Remove the 2 bushes.
Detach the 4 claws and remove the armrest hinge.
66990
21.REMOVE CUP HOLDER ASSEMBLY
Detach the 4 claws and remove the cup holder assembly.
22.REMOVE REAR SEATBACK ASSEMBLY RH
Remove the 14 hog rings.
Remove the 3 hog rings and detach the fastening rubber.
Detach the 8 claws and remove the 4 headrest supports.
Remove the seatback assembly.
79013
23.REMOVE NO. 1 SEATBACK COVER ASSEMBLY RH
Open the fastening tape.
Remove the 2 hog rings.
Remove the seatback cover.
72573
24.REMOVE RECLINING CONTROL LEVER RH
Remove the 2 bolts and reclining control lever.
71875C
25.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Remove the screw.
Detach the claw and remove the inside cover RH.
71876C
26.REMOVE NO. 2 RECLINING ADJUSTER INSIDE COVER LH
Remove the screw.
Detach the 2 claws and remove the inside cover LH.
71875C
27.REMOVE NO. 2 RECLINING ADJUSTER INSIDE COVER RH
Remove the screw.
Detach the 2 claws and remove the inside cover RH.
71834C
28.REMOVE REAR NO. 3 SEAT RECLINING COVER LH
Remove the 4 screws.
Detach the 4 claws and remove the cover.
71878B
29.REMOVE REAR SEAT RECLINING COVER INNER RH
Remove the 3 screws.
Detach the 2 claws and remove the cover.
71878A
30.REMOVE REAR SEAT RECLINING COVER INNER RH
Remove the screw and cover.
71499B
31.REMOVE SEAT CUSHION SPRING DAMPER
Remove the 2 nuts and spring damper.
79103A
32.REMOVE REAR NO. 1 SEATBACK FRAME SUB-ASSEMBLY RH
for LH Side:
Using a T55 "TORX" socket wrench , remove the 2 bolts (Bolt A).
Remove the 3 bolts (Bolt B and C).
Remove the seat hinge plate and bush.
for RH side:
Remove the 2 bolts (Bolt B).
Remove the seatback frame.
Remove the cover.
73310A
33.REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
73380C
34.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
72690
35.REMOVE SEAT CUSHION LOCK RELEASE LEVER ASSEMBLY
Remove the 2 screws.
Disconnect the rear No. 1 seat lock cable.
Remove the seat cushion lock release lever.
71015A
36.REMOVE REAR SEAT CUSHION FRAME ASSEMBLY RH
Open the 2 fasteners and then open the seat cushion cover.
Remove the 2 cable ties.
Remove the spring and disconnect the lock cable.
79011
37.REMOVE NO. 1 SEAT CUSHION COVER ASSEMBLY RH
Remove the 12 hog rings and seat cushion pad.