79011
1.INSTALL NO. 1 SEAT CUSHION COVER ASSEMBLY RH
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
71015A
2.INSTALL REAR SEAT CUSHION FRAME ASSEMBLY RH
Connect the lock cable and install the spring to the rear seat cushion frame.
Install the 2 cable ties.
Install the rear seat cushion frame to the rear seat cushion pad.
Turn down the seat cushion cover and close the 2 fasteners.
72690
3.INSTALL SEAT CUSHION LOCK RELEASE LEVER ASSEMBLY
Connect the rear No. 1 seat lock cable to the seat cushion lock release lever.
Install the seat cushion lock release lever with the 2 screws.
73380C
4.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
73310A
5.INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
79103A
6.INSTALL REAR NO. 1 SEATBACK FRAME SUB-ASSEMBLY RH
Install the cover.
Install the seatback frame.
for RH Side:
Install the 2 bolts (Bolt B).
for LH Side:
Install the bush and hinge plate.
Install the 3 bolts (Bolt B and C).
Using a T55 "TORX" socket wrench, install the 2 bolts (Bolt A).
71499B
7.INSTALL SEAT CUSHION SPRING DAMPER
Install the spring damper with the 2 nuts.
71878A
8.INSTALL REAR SEAT RECLINING COVER INNER RH
Install the cover with the screw.
71878B
9.INSTALL REAR SEAT RECLINING COVER INNER RH
Attach the 2 claws to install the cover.
Install the 3 screws.
71834C
10.INSTALL REAR NO. 3 SEAT RECLINING COVER LH
Attach the 4 claws to install the cover.
Install the 4 screws.
71875C
11.INSTALL NO. 2 RECLINING ADJUSTER INSIDE COVER RH
Attach the 2 claws to install the inside cover.
Install the screw.
71876C
12.INSTALL NO. 2 RECLINING ADJUSTER INSIDE COVER LH
Attach the 2 claws to install the inside cover.
Install the screw.
71875C
13.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Attach the claw to install the inside cover.
Install the screw.
72573
14.INSTALL RECLINING CONTROL LEVER RH
Install the reclining control lever with the 2 bolts.
79013
15.INSTALL NO. 1 SEATBACK COVER ASSEMBLY RH
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings and close the fastening tape.
16.INSTALL REAR SEATBACK ASSEMBLY RH
Install the seatback cover.
Attach the 8 claws to install the 4 headrest supports.
Using hog ring pliers, attach the fastening rubber and seatback assembly with new hog rings as shown in the illustration.
66990
17.INSTALL CUP HOLDER ASSEMBLY
Attach the 4 claws to install the cup holder.
71281A
18.INSTALL REAR SEAT CENTER ARMREST HINGE
Attach the 4 claws to install the armrest hinge.
Install the 2 bushes.
71349C
19.INSTALL REAR SEATBACK HINGE COVER
Install the seatback hinge cover with the bolt.
20.INSTALL CENTER ARMREST ASSEMBLY
Install the armrest with the 2 nuts.
Turn down the seat cover and close the fastener on the left side.
Using hog ring pliers, install the hog rings on the lower part of the seatback cover.
72830J
21.INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY RH
Install the armrest with the bolt.
71877B
22.INSTALL REAR SEAT ARMREST HOLE COVER RH
Attach the 2 claws to install the armrest hole cover.
73375
23.INSTALL REAR SEAT SHOULDER BELT COVER LH
Attach the 4 claws to install the cover.
73310
24.CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
73315
25.INSTALL REAR SEAT BELT COVER INNER RH
Install the seat belt cover with the 4 screws.
72615C
26.INSTALL REAR SEAT BACK LOCK STRIKER COVER
Attach the 3 claws to install the cover.
72927
27.INSTALL REAR SEAT CUSHION UNDER COVER RH
Install the seat cushion under cover with the 2 cushions and 4 screws.
71868J
28.INSTALL REAR SEAT CUSHION SHIELD RH (for LH Side)
Attach the 3 claws to install the seat cushion shield.
Install the screw.
29.INSTALL REAR SEAT CUSHION ASSEMBLY RH
for RH Side:
Install the seat cushion with the 3 bolts.
for bolt A
for bolt B
for LH Side:
Install the seat cushion with the bush and bolt.
71873C
30.INSTALL REAR SEAT CUSHION SHIELD LOWER RH
Attach the claw to install the cushion shield lower.
Install the screw.
71867K
31.INSTALL REAR SEAT CUSHION SHIELD LH (for RH Side)
Attach the 2 claws to install the cushion shield.
Install the screw.
71833A
32.INSTALL REAR NO. 1 SEAT RECLINING COVER RH
Attach the 7 claws to remove the reclining cover.
Attach the claws in the order indicated in the illustration.
Install the 2 screws.
72215
33.INSTALL SEAT TRACK HANDLE CONTROL LEVER RH
Attach the claw to install the seat track handle control lever.
72525C
34.INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH
Attach the claw to install the reclining adjuster release handle.
71834A
35.INSTALL REAR NO. 1 SEAT RECLINING COVER LH
Attach the 6 claws to install the reclining cover.
Attach the claws in the order indicated in the illustration.
73350A
36.INSTALL REAR NO. 1 SEAT LAP TYPE BELT ASSEMBLY CENTER
71848B
37.INSTALL SEAT ADJUSTER COVER CAP RH
Attach the claw to install the cap.