Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292011 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Driver Side Door Lock Motor Circuit  


DESCRIPTION

The driver side door lock motor is built into the front door lock on the driver side.

The main body ECU controls the driver side door lock motor to lock / unlock the driver side door. This ECU applies current from the positive terminal to the negative terminal to operate the motor to lock the door. It reverses the direction of the current flow to operate the motor to unlock the door.

WIRING DIAGRAM

B138810E46
1.76,1.188 3.875,1.344 2.115,0.156 10 false Front Door Lock (for Driver Side) 2.24,0.656 2.469,0.833 0.229,0.177 10 false UL 3.104,0.656 3.281,0.865 0.177,0.208 10 false L 0.167,2.146 1.01,2.323 0.844,0.177 10 false *1: for LHD 0.167,2.417 1.01,2.615 0.844,0.198 10 false *2: for RHD 4.875,2.188 5.969,2.354 1.094,0.167 10 false Main Body ECU 4.948,0.51 5.406,0.677 0.458,0.167 10 false ACT+ 4.948,1.625 5.406,1.792 0.458,0.167 10 false ACT- 4.875,2.042 5.125,2.208 0.25,0.167 10 false 4D 4.594,0.406 4.865,0.573 0.271,0.167 10 false 1*2 4.594,0.24 4.865,0.406 0.271,0.167 10 false 5*1 4.5,1.323 4.865,1.49 0.365,0.167 10 false 21*1 3.313,0.406 3.458,0.573 0.146,0.167 10 false 4 2.031,0.406 2.156,0.573 0.125,0.167 10 false 1 4.5,1.521 4.865,1.688 0.365,0.167 10 false 20*2 1.76,1.021 2.5,1.188 0.74,0.167 10 false J6*1, I6*2

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR LOCK)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the doors lock / unlock.

Main body ECU
Item Test Details Diagnostic Note
DOOR LOCK Operate door lock motor
LOCK / UNLOCK
-

OK:

Doors can lock / unlock.




NG

2.INSPECT FRONT DOOR LOCK ASSEMBLY (FOR DRIVER SIDE)

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT FRONT DOOR LOCK ASSEMBLY (FOR DRIVER SIDE)
a.
E123888E04
2.516,2.503 3.116,2.700 0.600,0.198 10 Unlock 1.403,2.788 1.753,2.972 0.350,0.184 10 Lock 0.704,3.332 0.850,3.526 0.145,0.194 10 L 2.649,3.47 2.895,3.654 0.246,0.184 10 UL 1.29,3.76 0.835,3.436 false 2.21,3.762 2.623,3.556 false

for LHD:

i.

Remove the driver side door lock.


ii.

Apply battery voltage to the motor terminals and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock




b.
E123889E06
1.723,2.772 2.073,2.956 0.351,0.184 10 Lock 0.4,2.584 0.903,2.782 0.503,0.198 10 Unlock 1.265,3.794 0.905,3.586 false 2.219,3.811 2.621,3.579 false 0.748,3.484 1.030,3.652 0.282,0.167 10 L 2.674,3.487 3.013,3.655 0.338,0.167 10 UL

for RHD:

i.

Remove the driver side door lock.


ii.

Apply battery voltage to the motor terminals and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock





OK

3.CHECK WIRE HARNESS (DOOR LOCK - ECU AND BODY GROUND)

NG

REPLACE FRONT DOOR LOCK ASSEMBLY (for Driver Side)

3.CHECK WIRE HARNESS (DOOR LOCK - ECU AND BODY GROUND)
U188679E02
2.76,1.042 2.938,0.823 false 2.094,1.052 1.625,0.667 false 4.135,1.01 4.25,0.698 false 4.583,1.01 4.969,0.698 false 4.469,1.198 4.198,1.51 false 4.573,1.198 4.75,1.51 false 0.042,0 1.396,0.177 1.354,0.177 10 false Wire Harness Side: 1.844,0 2.979,0.396 1.135,0.396 10 false Front Door Lock (Door Lock Motor) 1.365,0.948 1.615,1.104 0.25,0.156 10 false J6 1.385,1.208 1.552,1.396 0.167,0.188 10 false I6 4.625,0.063 5.698,0.24 1.073,0.177 10 false Main Body ECU 3.573,0.99 3.802,1.156 0.229,0.167 10 false 4D 1.615,0.906 1.802,1.094 0.188,0.188 10 false *1 1.615,1.167 1.833,1.333 0.219,0.167 10 false *2 2.979,0.625 3.146,0.854 0.167,0.229 10 false L 1.417,0.552 1.688,0.729 0.271,0.177 10 false UL 4.219,0.531 4.76,0.708 0.542,0.177 10 false ACT+*2 4.917,0.531 5.5,0.708 0.583,0.177 10 false ACT+*1 3.927,1.531 4.49,1.708 0.563,0.177 10 false ACT-*2 4.635,1.531 5.167,1.708 0.531,0.177 10 false ACT-*1 0.104,1.063 0.854,1.24 0.75,0.177 10 false *1: for LHD 0.104,1.344 0.854,1.531 0.75,0.188 10 false *2: for RHD

a.

for LHD:

i.

Disconnect the J6 front door lock connector.


ii.

Disconnect the 4D ECU connector.


iii.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
J6-4 (L) - 4D-5 (ACT+) Below 1 Ω
J6-1 (UL) - 4D-21 (ACT-) Below 1 Ω
J6-4 (L) - Body ground 10 kΩ or higher
J6-1 (UL) - Body ground 10 kΩ or higher




b.

for RHD:

i.

Disconnect the I6 front door lock connector.


ii.

Disconnect the 4D ECU connector.


iii.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
I6-4 (L) - 4D-1 (ACT+) Below 1 Ω
I6-1 (UL) - 4D-20 (ACT-) Below 1 Ω
I6-4 (L) - Body ground 10 kΩ or higher
I6-1 (UL) - Body ground 10 kΩ or higher





OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR