Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292011 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Driver Side Door Courtesy Switch Circuit  


DESCRIPTION

The driver side door courtesy light switch turns on when the driver side door is opened and turns off when the door is closed. The main body ECU applies voltage to the driver side door courtesy light switch. Driver side door open / close state signals are input to the main body ECU.

WIRING DIAGRAM

B138811E01
1.417,1.784 3.508,2.134 2.091,0.350 10 Front Door Courtesy Light Switch (for Driver Side) 4.875,2.22 5.892,2.413 1.017,0.193 10 Main Body ECU 4.953,1.193 5.386,1.358 0.434,0.165 10 DCTY 0.131,2.213 0.885,2.369 0.755,0.156 10 *1: for LHD 0.131,2.47 0.885,2.626 0.755,0.156 10 *2: for RHD 4.637,1.08 4.867,1.245 0.230,0.165 10 24 3.37,1.08 3.600,1.245 0.230,0.165 10 1 1.417,1.615 2.330,1.780 0.913,0.165 10 M5*1, N1*2 4.847,2.05 5.281,2.215 0.434,0.165 10 G57

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE DOOR COURTESY LIGHT SWITCH)
a.

Use the Data List to check if the door courtesy light switch is functioning properly.

Main body ECU
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
D Door Courtesy SW Driver side door courtesy light switch signal / ON or OFF ON: Driver side door is open
OFF: Driver side door is closed
-

OK:

When the switch is operating, the intelligent tester should display as shown in the table.




NG

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH (for Driver Side)

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH (for Driver Side)
a.
E114552E09
0.927,1.188 1.688,1.833 false 1.458,0.135 2.573,0.313 1.115,0.177 10 false Not Pushed (ON) 1.521,0.563 2.469,0.75 0.948,0.188 10 false Pushed (OFF) 1.74,1.771 2.625,1.938 0.885,0.167 10 false Body Ground

Remove the door courtesy light switch.


b.

Measure the resistance of the door courtesy switch connector.

Standard resistance:
Tester Connection Condition Specified Condition
1 - Body ground Pushed (OFF) 10 kΩ or higher
1 - Body ground Not pushed (ON) Below 1 Ω




OK

3.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH (for Driver Side)

3.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)
a.
U188683E01
0.024,0 1.416,0.177 1.392,0.177 10 Wire Harness Side: 0.706,0.494 2.445,0.636 1.739,0.142 10 Door Courtesy Light Switch 0.665,1.251 0.911,1.396 0.246,0.145 10 M5 0.672,1.645 0.898,1.808 0.225,0.163 10 N1 1.023,1.191 1.217,1.347 0.194,0.156 10 *1 1.023,1.583 1.207,1.732 0.184,0.149 10 *2 1.11,2.445 2.161,2.629 1.052,0.184 10 Main Body ECU 0.362,3.459 0.665,3.648 0.303,0.189 10 G57 2.009,4.356 2.408,4.511 0.399,0.156 10 DCTY 2.191,4.006 2.235,4.35 false 0.045,3.921 0.775,4.086 0.730,0.165 10 *1: for LHD 0.045,4.264 0.775,4.436 0.730,0.172 10 *2: for RHD

for LHD:

i.

Disconnect the M5 switch connector.


ii.

Disconnect the G57 ECU connector.


iii.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
M5-1 - G57-24 (DCTY) Below 1 Ω
M5-1 - Body ground 10 kΩ or higher




b.

for RHD:

i.

Disconnect the N1 switch connector.


ii.

Disconnect the G57 ECU connector.


iii.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
N1-1 - G57-24 (DCTY) Below 1 Ω
N1-1 - Body ground 10 kΩ or higher





OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR