Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292011 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Back Door Courtesy Switch Circuit  


DESCRIPTION

The back door courtesy light switch is built into the back door lock. The switch turns on when the back door is opened and turns off when the door is closed. The main body ECU applies voltage to the back door lock via terminal BCTY. Back door open / close state signals are input to the main body ECU.

WIRING DIAGRAM

B138813E07
1.735,1.808 3.243,2.167 1.508,0.360 10 Back Door Lock (Courtesy Light Switch) 4.875,2.259 5.938,2.433 1.063,0.174 10 Main Body ECU 4.959,1.221 5.420,1.396 0.461,0.174 10 BCTY 1.64,1.313 2.252,1.525 0.612,0.211 10 ACT- 3.07,1.313 3.293,1.460 0.223,0.147 10 D+ 4.875,2.092 5.174,2.294 0.299,0.202 10 G58 1.735,1.653 2.035,1.856 0.299,0.202 10 S11 1.426,1.096 1.567,1.277 0.141,0.181 10 1 3.364,1.096 3.504,1.277 0.141,0.181 10 3 4.654,1.096 4.911,1.277 0.257,0.181 10 25

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (BACK DOOR COURTESY LIGHT SWITCH)
a.

Use the Data List to check if the door courtesy light switch is functioning properly.

Main body ECU
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy light switch signal / ON or OFF ON: Back door is open
OFF: Back door is closed
-

OK:

When the switch is operating, the intelligent tester should display as shown in the table.




NG

2.INSPECT BACK DOOR LOCK ASSEMBLY

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT BACK DOOR LOCK ASSEMBLY
a.
B138839E07
0.708,0.938 0.771,0.51 0.771,0.51 0.844,0.51 false 1.073,0.99 0.99,1.406 0.99,1.406 0.917,1.406 false 0.802,2.958 1.448,3.135 0.646,0.177 10 false Full-latch 0.802,3.563 1.531,3.74 0.729,0.177 10 false Open-latch 0.563,1.313 0.99,1.49 0.427,0.177 10 false ACT- 0.896,0.427 1.188,0.604 0.292,0.177 10 false D+

Remove the back door lock.


b.

Measure the resistance of the back door lock.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1(ACT-) -3 (D+) Open-latch Below 1 Ω
1(ACT-) -3 (D+) Full-latch 10 kΩ or higher




OK

3.CHECK WIRE HARNESS (DOOR LOCK - ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

3.CHECK WIRE HARNESS (DOOR LOCK - ECU AND BODY GROUND)
a.
U188684E01
0.081,0.08 1.411,0.236 1.330,0.156 10 Wire Harness Side: 1.062,0.698 2.162,0.840 1.100,0.142 10 Back Door Lock 1.119,2.628 2.156,2.811 1.038,0.184 10 Main Body ECU 0.454,1.568 0.740,1.746 0.286,0.178 10 S11 0.254,3.629 0.560,3.773 0.306,0.145 10 G58 2.308,2.168 2.554,2.345 0.246,0.177 10 D+ 1.71,4.476 2.106,4.620 0.395,0.144 10 BCTY 2.011,1.712 2.308,2.155 false 1.933,3.983 1.933,4.464 false 0.858,2.155 1.226,2.332 0.368,0.177 10 ACT- 1.386,1.696 1.006,2.075 false

Disconnect the S11 back door lock connector.


b.

Disconnect the G58 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
S11-3 (D+) - G58-25 (BCTY) Below 1 Ω
S11-1 (ACT-) - Body ground Below 1 Ω
S11-3 (D+) - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR