Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292011 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Slide Door Lock Motor LH Circuit  


DESCRIPTION

The slide door lock motor LH is built into the rear door lock actuator assembly LH.

The main body ECU controls the slide door lock motor LH to lock / unlock the slide door LH. This ECU applies current from the positive terminal to the negative terminal to operate the motor to lock the door. It reverses the direction of the current flow to operate the motor to unlock the door.

WIRING DIAGRAM

B138810E33
1.964,1.069 3.542,1.592 1.577,0.523 10 Rear Door Lock Actuator Assembly LH 2.243,0.669 2.469,0.846 0.225,0.177 10 UL 3.314,0.438 3.491,0.643 0.177,0.205 10 2 3.09,0.669 3.267,0.874 0.177,0.205 10 L 4.712,0.438 4.889,0.643 0.177,0.205 10 7 4.651,1.546 4.920,1.751 0.269,0.205 10 23 4.882,2.051 5.151,2.255 0.269,0.205 10 4G 1.964,0.922 2.234,1.126 0.269,0.205 10 L3 2.031,0.438 2.207,0.643 0.177,0.205 10 3 4.88,2.21 5.918,2.366 1.038,0.156 10 Main Body ECU 4.954,0.545 5.408,0.708 0.455,0.163 10 ACT+ 4.954,1.665 5.408,1.828 0.455,0.163 10 ACT-

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR LOCK)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the doors lock / unlock.

Main body ECU
Item Test Details Diagnostic Note
DOOR LOCK Operate door lock motor
LOCK / UNLOCK
-

OK:

Doors can lock / unlock.




NG

2.INSPECT REAR DOOR LOCK ACTUATOR ASSEMBLY LH

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT REAR DOOR LOCK ACTUATOR ASSEMBLY LH
a.
B256274E09
2.526,0.393 2.968,0.575 0.442,0.181 10 Unlock 0.245,0.601 0.555,0.782 0.310,0.181 10 Lock 1.448,1.377 0.949,0.688 0.949,0.688 0.653,0.688 false 1.943,1.048 2.226,0.477 2.226,0.477 2.502,0.477 false 1.126,3.492 1.351,3.673 0.225,0.181 10 UL 2.206,3.492 2.359,3.660 0.152,0.167 10 L 1.639,4.217 1.238,3.673 false 1.852,4.217 2.253,3.673 false

Remove the rear door lock actuator assembly LH.


b.

Apply battery voltage to the motor terminals and check the operation of the door lock motor.

OK:
Measurement Condition Result
Battery positive (+) → 2 (L)
Battery negative (-) → 3 (UL)
Locks
Battery positive (+) → 3 (UL)
Battery negative (-) → 2 (L)
Unlocks




OK

3.CHECK WIRE HARNESS (DOOR LOCK - ECU AND BODY GROUND)

NG

REPLACE REAR DOOR LOCK ACTUATOR ASSEMBLY LH

3.CHECK WIRE HARNESS (DOOR LOCK - ECU AND BODY GROUND)
a.
U188681E02
1.333,3.854 1.146,4.417 false 1.667,4.052 1.833,4.406 false 1.583,1.854 0.99,1.49 false 1.896,1.844 2.49,1.438 false 0.052,0.052 1.438,0.26 1.385,0.208 10 false Wire Harness Side: 0.24,0.49 2.625,0.844 2.385,0.354 10 false Rear Door Lock Actuator Assembly LH (Door Lock Motor) 1.146,2.885 2.208,3.042 1.063,0.156 10 false Main Body ECU 0.479,1.813 0.688,2.021 0.208,0.208 10 false L3 0.26,3.146 0.531,3.313 0.271,0.167 10 false 4G 0.875,1.323 1,1.51 0.125,0.188 10 false L 2.521,1.302 2.792,1.469 0.271,0.167 10 false UL 0.938,4.448 1.354,4.604 0.417,0.156 10 false ACT+ 1.667,4.448 2.083,4.604 0.417,0.156 10 false ACT-

Disconnect the L3 rear door lock actuator assembly LH connector.


b.

Disconnect the 4G ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
L3-2 (L) - 4G-7 (ACT+) Below 1 Ω
L3-3 (UL) - 4G-23 (ACT-) Below 1 Ω
L3-2 (L) - Body ground 10 kΩ or higher
L3-3 (UL) - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR