Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292011 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Back Door Lock Motor Circuit  


DESCRIPTION

The back door lock motor is built into the back door lock.

The main body ECU controls the back door lock motor to lock / unlock the back door. This ECU applies current from the positive terminal to the negative terminal to operate the motor to lock the door. It reverses the direction of the current flow to operate the motor to unlock the door.

WIRING DIAGRAM

B138815E01
2.211,1.587 3.235,1.743 1.024,0.156 10 Back Door Lock 2.841,1.107 3.299,1.266 0.458,0.159 10 ACT+ 2.236,1.107 2.694,1.266 0.458,0.159 10 ACT- 4.941,0.944 5.237,1.112 0.296,0.168 10 TR+ 4.702,0.836 4.866,1.004 0.164,0.168 10 1 2.026,0.836 2.190,1.004 0.164,0.168 10 1 3.308,0.836 3.472,1.004 0.164,0.168 10 2 4.867,1.824 5.163,1.992 0.296,0.168 10 G57 2.211,1.433 2.507,1.601 0.296,0.168 10 S11 4.867,1.963 5.926,2.125 1.059,0.163 10 Main Body ECU

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR LOCK)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the doors lock / unlock.

Main body ECU
Item Test Details Diagnostic Note
DOOR LOCK Operate door lock motor LOCK / UNLOCK -

OK:

Doors can lock / unlock.




NG

2.INSPECT BACK DOOR LOCK ASSEMBLY

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT BACK DOOR LOCK ASSEMBLY
a.
B138839E08
1.063,0.99 0.979,1.406 0.979,1.406 0.906,1.406 false 0.865,0.938 0.844,0.51 0.844,0.51 0.917,0.51 false 0.802,2.969 1.448,3.146 0.646,0.177 10 false Full-latch 0.802,3.563 1.531,3.74 0.729,0.177 10 false Open-latch 0.531,1.313 0.958,1.49 0.427,0.177 10 false ACT- 0.948,0.427 1.344,0.604 0.396,0.177 10 false ACT+

Remove the back door lock.


b.

Apply battery voltage to the motor terminals and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (ACT+)
Battery negative (-) → 1 (ACT-)
Lock
Battery positive (+) → 1 (ACT-)
Battery negative (-) → 2 (ACT+)
Unlock




OK

3.CHECK WIRE HARNESS (DOOR LOCK - ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

3.CHECK WIRE HARNESS (DOOR LOCK - ECU AND BODY GROUND)
a.
U188682E02
1.708,1.677 1.708,2.156 false 1.083,3.604 0.781,3.302 false 1.427,1.656 1.021,2.146 false 0.063,0.063 1.448,0.24 1.385,0.177 10 false Wire Harness Side: 1.104,0.656 2.167,0.802 1.063,0.146 10 false Back Door Lock 0.26,1.542 0.583,1.729 0.323,0.188 10 false S11 1.125,2.625 2.135,2.802 1.01,0.177 10 false Main Body ECU 0.406,3.708 0.74,3.906 0.333,0.198 10 false G57 1.531,2.177 1.958,2.344 0.427,0.167 10 false ACT+ 0.427,3.146 0.781,3.313 0.354,0.167 10 false TR+ 0.74,2.156 1.167,2.323 0.427,0.167 10 false ACT-

Disconnect the S11 back door lock connector.


b.

Disconnect the G57 body ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
S11-2 (ACT+) - G57-1 (TR+) Below 1 Ω
S11-1 (ACT-) - Body ground Below 1 Ω
S11-2 (ACT+) - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR