Home › Vehicle Interior › DOOR LOCK › BACK DOOR LOCK
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292015 BACK DOOR LOCK G

DOOR LOCK  BACK DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69350 1.INSPECT BACK DOOR LOCK ASSEMBLY (w/o Power Back Door Control System)

a.
B138839E09
0.698,0.938 0.385,0.51 0.385,0.51 0.458,0.51 false 1.052,1 0.969,1.417 0.969,1.417 0.896,1.417 false 0.865,0.938 0.844,0.51 0.844,0.51 0.917,0.51 false 0.802,2.99 1.448,3.167 0.646,0.177 10 false Full-latch 0.771,3.563 1.5,3.74 0.729,0.177 10 false Open-latch 0.542,1.323 0.969,1.5 0.427,0.177 10 false ACT- 0.51,0.438 0.802,0.615 0.292,0.177 10 false D+ 0.958,0.427 1.354,0.604 0.396,0.177 10 false ACT+

Apply battery voltage to the motor terminals and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (ACT+)
Battery negative (-) → 1 (ACT-)
Lock
Battery positive (+) → 1 (ACT-)
Battery negative (-) → 2 (ACT+)
Unlock


If the result is not as specified, replace the back door assembly.



b.

Measure the resistance of the back door lock.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 (ACT+) - 3 (D+) Open-latch Below 1 Ω
1 (ACT+) - 3 (D+) Full-latch 10 kΩ or higher


If the result is not as specified, replace the back door assembly.



Hide 69350 2.INSPECT BACK DOOR LOCK ASSEMBLY (w/ Power Back Door Control System)

B143899E06
4.43,3.957 5.123,4.113 0.693,0.156 10 Over-latch 4.322,4.279 4.936,4.426 0.614,0.147 10 Full-latch 4.112,5.227 4.731,5.369 0.619,0.142 10 Half-latch 3.72,5.853 4.450,6.027 0.730,0.174 10 Open-latch 3.201,1.766 3.607,1.918 0.406,0.151 10 Close 2.193,1.734 2.724,1.876 0.531,0.142 10 Release 3.827,3.532 4.539,3.692 0.711,0.161 10 Drive Gear 3.085,2.514 3.752,3.588 3.752,3.588 3.799,3.588 false 5.348,2.662 5.779,2.811 0.430,0.149 10 ULSW 4.482,2.65 4.613,2.806 0.132,0.156 10 E 4.739,2.669 5.166,2.807 0.427,0.139 10 DLSW 4.96,2.644 5.187,2.13 false 5.366,2.104 5.527,2.662 false 4.542,2.626 5.177,1.935 false 5.201,1.749 4.43,2.355 false 5.366,1.927 5.967,2.499 false 5.366,1.749 5.985,2.121 false 6.015,2.063 6.405,2.254 0.390,0.191 10 M+ 6.015,2.46 6.405,2.651 0.390,0.191 10 CTY 4.217,2.301 4.607,2.492 0.390,0.191 10 M-

a.

Apply battery voltage and check operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (M+)
Battery negative (-) → 2 (M-)
Latch turns to open-latch position
Battery positive (+) → 2 (M-)
Battery negative (-) → 1 (M+)
Latch turns to open-latch position


If the result is not as specified, replace the back door assembly.


b.

Measure the resistance of the back door lock.

Standard resistance:
Full-latch switch
Tester Connection Switch Condition Specified Condition
5 (ULSW) - 4 (E) Over-latch Below 1 Ω
5 (ULSW) - 4 (E) Open-latch 10 kΩ or higher
5 (ULSW) - 4 (E) Full-latch 10 kΩ or higher
5 (ULSW) - 4 (E) Half-latch 10 kΩ or higher


Selector switch:
Tester Connection Switch Condition Specified Condition
6 (DLSW) - 4 (E) Open-latch Below 1 Ω
6 (DLSW) - 4 (E) Over-latch 10 kΩ or higher
6 (DLSW) - 4 (E) Full-latch 10 kΩ or higher
6 (DLSW) - 4 (E) Half-latch 10 kΩ or higher


Back door courtesy light switch:
Tester Connection Switch Condition Specified Condition
3 (CTY) - 4 (E) Open-latch Below 1 Ω
3 (CTY) - 4 (E) Half-latch 10 kΩ or higher
3 (CTY) - 4 (E) Full-latch 10 kΩ or higher
3 (CTY) - 4 (E) Over-latch 10 kΩ or higher


If the result is not as specified, replace the back door assembly.