CHECK CERTIFICATION ECU
Disconnect the G29 ECU connector.
Measure the resistance and voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| E (G29-17) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| +B (G29-1) - Body ground | BE - Body ground | +B power supply | Always | 10 to 14 V |
| IG (G29-18) - Body ground | B - Body ground | Ignition power supply | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | 10 to 14 V | |||
| TSW1 (G29-3) - E (G29-17) | V - W-B | Door outside handle (driver side) lock switch signal | Switch released | 10 kΩ or higher |
| Switch pressed in | Below 1 Ω | |||
| TSW2 (G29-4) - E (G29-17) | W - W-B | Door outside handle (front passenger side) lock switch signal | Switch released | 10 kΩ or higher |
| Switch pressed in | Below 1 Ω | |||
| TSW5 (G29-7) - E (G29-17) | GR - W-B | Back door lock switch signal | Switch released | 10 kΩ or higher |
| Switch pressed in | Below 1 Ω | |||
| LIN (G29-10) - E (G29-17) | R - W-B | LIN line | Always | 10 kΩ or higher |
If the result is not as specified, the wire harness side may have a malfunction.
Reconnect the G29 ECU connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| CLG1 (G29-33) - CG1B (G29-34) | L - LG | Door electrical key oscillator (driver side) sensor signal | With ignition switch OFF and doors closed, driver door lock switch OFF → ON | Hz output → no Hz out |
| SEN1 (G29-22) - E (G29-17) | P - W-B | Touch sensor detection signal | Outside door handle touched | 10 to 14 V |
| Outside door handle not touched | Below 1 V | |||
| SEL1 (G29-5) - E (G29-17) | BE - W-B | Touch sensor activation control signal | Key at least 5 m (16.4 ft.) away from door | 10 to 14 V |
| Key is moved near outside door handle | Below 1 V | |||
| CLG2 (G29-35) - CG2B (G29-36) | P - V | Door electrical key oscillator (front passenger side) sensor signal | With ignition switch OFF and doors closed, front passenger door lock switch OFF → ON | Hz output → no Hz output |
| SEN2 (G29-23) - E (G29-17) | G - W-B | Touch sensor detection signal | Outside door handle touched | 10 to 14 V |
| Outside door handle not touched | Below 1 V | |||
| SEL2 (G29-6) - E (G29-17) | SB - W-B | Touch sensor activation control signal | Key at least 5 m (16.4 ft.) away from door | 10 to 14 V |
| Key is moved near outside door handle | Below 1 V | |||
| CLG5 (G29-11) - CG5B (G29-12) | P - V | Indoor electrical key antenna (for front) sensor signal | 30 seconds after driver side door opened and closed, ignition switch off | Hz output → no Hz output |
| CLG6 (G29-13) - CG6B (G29-14) | B - Y | Indoor electrical key antenna (for rear1) sensor signal | 30 seconds after driver side door opened and closed, ignition switch off | Hz output → no Hz output |
| CLG7 (G29-15) - CG7B (G29-16) | B - G | Indoor electrical key antenna (for rear2) sensor signal | 30 seconds after driver side door opened and closed, ignition switch off | Hz output → no Hz output |
| CLG8 (G29-31) - CG8B (G29-32) | BR - GR | Back door electrical key antenna (for outer) sensor signal | With ignition switch OFF and doors closed, back door unlock switch OFF → ON | Hz output → no Hz output |
| RCO (G29-29) - E (G29-17) | P - W-B | Door control receiver power source | Ignition switch off, all doors closed and transmitter switch not pressed → pressed | Below 1 V → 4.6 to 5.4 V → Below 1 V |
| RSSI (G29-39) - E (G29-17) | BE - W-B | Door control receiver electric wave existence signal | Ignition switch off, all doors closed and transmitter switch not pressed → pressed | 10 to 14 V → Below 1 V |
| RDA (G29-38) - E (G29-17) | V - W-B | Door control receiver data input signal | Ignition switch off, all doors closed and transmitter switch not pressed → pressed | Below 1 V → 10 to 14 V → Below 1 V |
| BZR (G29-21) - E (G29-17) | SB - W-B | Wireless door lock buzzer signal | Answer-back ON | Pulse generation |
| Answer-back OFF | Below 1 V |
If the result is not as specified, the ECU may have a malfunction.
CHECK DOOR ELECTRICAL KEY OSCILLATOR (for Front Door)
Disconnect the h2 or g2 oscillator connector.
Measure the resistance and voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| GND (h2-7) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| +B (h2-1) - GND (h2-7) | Y - BR | +B power supply | Always | 10 to 14 V |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| GND (g2-7) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| +B (g2-1) - GND (g2-7) | Y - BR | +B power supply | Always | 10 to 14 V |
If the result is not as specified, the wire harness side may have a malfunction.
Reconnect the h2 or g2 oscillator connector.
Measure the voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| CLG (h2-10) - GND (h2-7) | R - BR | Door electrical key oscillator (driver side) sensor signal | With ignition switch OFF and doors closed, driver door lock switch OFF → ON | Alternating between 5 V and below 1 V |
| Door unlocked or door open | Below 1 V | |||
| SEL (h2-4) - GND (h2-7) | O - BR | Touch sensor activation control signal | Key at least 5 m (16.4 ft.) away from door | 10 to 14 V |
| Key is moved near outside door handle | Below 1 V | |||
| SENS (h2-6) - GND (h2-7) | V - BR | Touch sensor detection signal | Outside door handle touched | 10 to 14 V |
| Outside door handle not touched | Below 1 V |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| CLG (g2-10) - GND (g2-7) | R - BR | Door electrical key oscillator sensor signal | With ignition switch OFF and doors closed, front passenger door lock switch OFF → ON | Alternating between 5 V and below 1 V |
| Door unlocked or door open | Below 1 V | |||
| SEL (g2-4) - GND (g2-7) | O - BR | Touch sensor activation control signal | Key at least 5 m (16.4 ft.) away from door | 10 to 14 V |
| Key is moved near outside door handle | Below 1 V | |||
| SENS (g2-6) - GND (g2-7) | V - BR | Touch sensor detection signal | Outside door handle touched | 10 to 14 V |
| Outside door handle not touched | Below 1 V |
If the result is not as specified, the oscillator may have a malfunction.
CHECK BACK DOOR ELECTRICAL KEY ANTENNA (for Outer)
Measure the voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| CLG5 (M1-1) - CLGB (M1-2) | W - R | Back door electrical key antenna (outer) sensor signal | Back door unlock switch OFF | Alternating between 5 V and below 1 V |
| Back door unlock switch ON | Below 1 V |
If the result is not as specified, the oscillator may have a malfunction.
CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)
Disconnect the G57, G59, 4A, 4K, and 4M ECU connectors.
Measure the resistance and voltage of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| GND1(G59-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| GND2 (4A-3) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| BATB (4K-9) - Body ground | B - Body ground | BATB power supply | Always | 10 to 14 V |
| AM1 (G57-6) - Body ground | SB - Body ground | AM1 power supply | Always | 10 to 14 V |
| AM2 (G58-1) - Body ground | SB - Body ground | AM2 power supply | Always | 10 to 14 V |
| IG (4M-1) - Body ground | W - Body ground | IG1 signal | Ignition switch on (IG) | 10 to 14 V |
| Ignition switch off | Below 1 V | |||
| ACC (4A-26) - Body ground | GR - Body ground | ACC signal | Ignition switch on (ACC) | 10 to 14 V |
| CANN (G59-15) - Body ground | W - Body ground | CAN communication line | Always | 10 kΩ or higher |
| CANP (G59-16) - Body ground | B - Body ground | CAN communication line | Always | 10 kΩ or higher |
| LIN1(4A-20) - Body ground | R - Body ground | LIN communication line | Always | 10 kΩ or higher |
If the result is not as specified, the wire harness side may have a malfunction.
Reconnect the G57, G58, 4A, 4K and 4M ECU connectors.
Measure the voltage of the connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| DCTY (G57-24) - Body ground | L - Body ground | Driver side door courtesy light switch input | Driver side door closed | 10 to 14 V |
| Driver side door open | Below 1 V | |||
| PCTY (G58-21) - Body ground | L - Body ground | Front passenger side door courtesy light switch input | Front passenger side door closed | 10 to 14 V |
| Front passenger side door open | Below 1 V | |||
| RCTY (G58-7) - Body ground | LG- Body ground | Slide door RH courtesy light switch input | Slide door RH closed | 10 to 14 V |
| Slide door RH open | Below 1 V | |||
| LCTY (4A-4) - Body ground | BE - Body ground | Slide door LH courtesy light switch input | Slide door LH closed | 10 to 14 V |
| Slide door LH open | Below 1 V | |||
| BCYL (G57-19) - Body ground | R- Body ground | Back door courtesy light switch input | Back side door closed | 10 to 14 V |
| Back side door open | Below 1 V | |||
| HAZ (G59-4) - Body ground | GR- Body ground | Hazard warning light signal | Answer-back ON | Below 1 V |
| Answer-back OFF | 10 to 14 V |
If the result is not as specified, the main body ECU may have a malfunction.