Home › Vehicle Interior › DOOR LOCK › SMART ENTRY AND START SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292017 SMART ENTRY AND START SYSTEM U

DOOR LOCK  SMART ENTRY AND START SYSTEM  TERMINALS OF ECU  


CHECK CERTIFICATION ECU


U185919E02
2.083,0.188 2.406,0.385 0.323,0.198 10 false G29 5.135,0.188 5.458,0.385 0.323,0.198 10 false G30

a.

Disconnect the G29 ECU connector.


b.

Measure the resistance and voltage of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
E (G29-17) - Body ground W-B - Body ground Ground Always Below 1 Ω
+B (G29-1) - Body ground BE - Body ground +B power supply Always 10 to 14 V
IG (G29-18) - Body ground B - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch on (IG) 10 to 14 V
TSW1 (G29-3) - E (G29-17) V - W-B Door outside handle (driver side) lock switch signal Switch released 10 kΩ or higher
Switch pressed in Below 1 Ω
TSW2 (G29-4) - E (G29-17) W - W-B Door outside handle (front passenger side) lock switch signal Switch released 10 kΩ or higher
Switch pressed in Below 1 Ω
TSW5 (G29-7) - E (G29-17) GR - W-B Back door lock switch signal Switch released 10 kΩ or higher
Switch pressed in Below 1 Ω
LIN (G29-10) - E (G29-17) R - W-B LIN line Always 10 kΩ or higher

If the result is not as specified, the wire harness side may have a malfunction.



c.

Reconnect the G29 ECU connector.


d.

Measure the voltage of the connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
CLG1 (G29-33) - CG1B (G29-34) L - LG Door electrical key oscillator (driver side) sensor signal With ignition switch OFF and doors closed, driver door lock switch OFF → ON Hz output → no Hz out
SEN1 (G29-22) - E (G29-17) P - W-B Touch sensor detection signal Outside door handle touched 10 to 14 V
Outside door handle not touched Below 1 V
SEL1 (G29-5) - E (G29-17) BE - W-B Touch sensor activation control signal Key at least 5 m (16.4 ft.) away from door 10 to 14 V
Key is moved near outside door handle Below 1 V
CLG2 (G29-35) - CG2B (G29-36) P - V Door electrical key oscillator (front passenger side) sensor signal With ignition switch OFF and doors closed, front passenger door lock switch OFF → ON Hz output → no Hz output
SEN2 (G29-23) - E (G29-17) G - W-B Touch sensor detection signal Outside door handle touched 10 to 14 V
Outside door handle not touched Below 1 V
SEL2 (G29-6) - E (G29-17) SB - W-B Touch sensor activation control signal Key at least 5 m (16.4 ft.) away from door 10 to 14 V
Key is moved near outside door handle Below 1 V
CLG5 (G29-11) - CG5B (G29-12) P - V Indoor electrical key antenna (for front) sensor signal 30 seconds after driver side door opened and closed, ignition switch off Hz output → no Hz output
CLG6 (G29-13) - CG6B (G29-14) B - Y Indoor electrical key antenna (for rear1) sensor signal 30 seconds after driver side door opened and closed, ignition switch off Hz output → no Hz output
CLG7 (G29-15) - CG7B (G29-16) B - G Indoor electrical key antenna (for rear2) sensor signal 30 seconds after driver side door opened and closed, ignition switch off Hz output → no Hz output
CLG8 (G29-31) - CG8B (G29-32) BR - GR Back door electrical key antenna (for outer) sensor signal With ignition switch OFF and doors closed, back door unlock switch OFF → ON Hz output → no Hz output
RCO (G29-29) - E (G29-17) P - W-B Door control receiver power source Ignition switch off, all doors closed and transmitter switch not pressed → pressed Below 1 V → 4.6 to 5.4 V → Below 1 V
RSSI (G29-39) - E (G29-17) BE - W-B Door control receiver electric wave existence signal Ignition switch off, all doors closed and transmitter switch not pressed → pressed 10 to 14 V → Below 1 V
RDA (G29-38) - E (G29-17) V - W-B Door control receiver data input signal Ignition switch off, all doors closed and transmitter switch not pressed → pressed Below 1 V → 10 to 14 V → Below 1 V
BZR (G29-21) - E (G29-17) SB - W-B Wireless door lock buzzer signal Answer-back ON Pulse generation
Answer-back OFF Below 1 V

If the result is not as specified, the ECU may have a malfunction.




CHECK DOOR ELECTRICAL KEY OSCILLATOR (for Front Door)


U188599E02
3.865,0.385 4.063,0.563 0.198,0.177 10 false g2 3.115,0.396 3.302,0.573 0.188,0.177 10 false h2 3.479,0.375 3.667,0.552 0.188,0.177 10 false *1 4.229,0.375 4.417,0.552 0.188,0.177 10 false *2 0.115,1.427 1.906,1.615 1.792,0.188 10 false *2: for Front Passenger Side 0.115,1.146 1.292,1.313 1.177,0.167 10 false *1: for Driver Side

a.

Disconnect the h2 or g2 oscillator connector.


b.

Measure the resistance and voltage of the wire harness side connector.

for Driver side:
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND (h2-7) - Body ground BR - Body ground Ground Always Below 1 Ω
+B (h2-1) - GND (h2-7) Y - BR +B power supply Always 10 to 14 V

for Front passenger side:
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND (g2-7) - Body ground BR - Body ground Ground Always Below 1 Ω
+B (g2-1) - GND (g2-7) Y - BR +B power supply Always 10 to 14 V

If the result is not as specified, the wire harness side may have a malfunction.



c.

Reconnect the h2 or g2 oscillator connector.


d.

Measure the voltage of the wire harness side connector.

for Driver side:
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
CLG (h2-10) - GND (h2-7) R - BR Door electrical key oscillator (driver side) sensor signal With ignition switch OFF and doors closed, driver door lock switch OFF → ON Alternating between 5 V and below 1 V
Door unlocked or door open Below 1 V
SEL (h2-4) - GND (h2-7) O - BR Touch sensor activation control signal Key at least 5 m (16.4 ft.) away from door 10 to 14 V
Key is moved near outside door handle Below 1 V
SENS (h2-6) - GND (h2-7) V - BR Touch sensor detection signal Outside door handle touched 10 to 14 V
Outside door handle not touched Below 1 V

for Front passenger side:
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
CLG (g2-10) - GND (g2-7) R - BR Door electrical key oscillator sensor signal With ignition switch OFF and doors closed, front passenger door lock switch OFF → ON Alternating between 5 V and below 1 V
Door unlocked or door open Below 1 V
SEL (g2-4) - GND (g2-7) O - BR Touch sensor activation control signal Key at least 5 m (16.4 ft.) away from door 10 to 14 V
Key is moved near outside door handle Below 1 V
SENS (g2-6) - GND (g2-7) V - BR Touch sensor detection signal Outside door handle touched 10 to 14 V
Outside door handle not touched Below 1 V

If the result is not as specified, the oscillator may have a malfunction.




CHECK BACK DOOR ELECTRICAL KEY ANTENNA (for Outer)


U185943E02
3.271,0.052 3.51,0.198 0.24,0.146 10 false M1

a.

Measure the voltage of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
CLG5 (M1-1) - CLGB (M1-2) W - R Back door electrical key antenna (outer) sensor signal Back door unlock switch OFF Alternating between 5 V and below 1 V
Back door unlock switch ON Below 1 V

If the result is not as specified, the oscillator may have a malfunction.




CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)


U188715E02
2.771,7.313 3.073,7.458 0.302,0.146 10 false G60 3.177,6 3.427,6.146 0.25,0.146 10 false 4P 5.708,2.406 5.958,2.552 0.25,0.146 10 false 4P 5.688,3.219 5.938,3.365 0.25,0.146 10 false 4O 1.313,1.542 1.563,1.688 0.25,0.146 10 false 4A 1.698,4.604 1.948,4.75 0.25,0.146 10 false 4A 0.646,6.052 0.896,6.198 0.25,0.146 10 false 4O 3.417,7.313 3.719,7.458 0.302,0.146 10 false G59 4.344,7.313 4.646,7.458 0.302,0.146 10 false G58 5.573,7.313 5.875,7.458 0.302,0.146 10 false G57 6.083,1.5 6.385,1.646 0.302,0.146 10 false G57 6.083,2.031 6.385,2.177 0.302,0.146 10 false G58 6.083,2.49 6.385,2.635 0.302,0.146 10 false G59 6.083,2.813 6.385,2.958 0.302,0.146 10 false G60 0.542,0.115 1.719,0.292 1.177,0.177 10 false Vehicle Front Side 5.594,0.125 6.771,0.302 1.177,0.177 10 false Vehicle Rear Side

a.

Disconnect the G57, G59, 4A, 4P, and 4O ECU connectors.


b.

Measure the resistance and voltage of the wire harness side connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND1(G59-1) - Body ground W-B - Body ground Ground Always Below 1 Ω
GND2 (4A-3) - Body ground W-B - Body ground Ground Always Below 1 Ω
BATB (4P-9) - Body ground B - Body ground BATB power supply Always 10 to 14 V
AM1 (G57-6) - Body ground SB - Body ground AM1 power supply Always 10 to 14 V
AM2 (G58-1) - Body ground SB - Body ground AM2 power supply Always 10 to 14 V
IG (4O-1) - Body ground W - Body ground IG1 signal Ignition switch on (IG) 10 to 14 V
Ignition switch off Below 1 V
ACC (4A-26) - Body ground GR - Body ground ACC signal Ignition switch on (ACC) 10 to 14 V
CANN (G59-15) - Body ground W - Body ground CAN communication line Always 10 kΩ or higher
CANP (G59-16) - Body ground B - Body ground CAN communication line Always 10 kΩ or higher
LIN1(4A-20) - Body ground R - Body ground LIN communication line Always 10 kΩ or higher

If the result is not as specified, the wire harness side may have a malfunction.



c.

Reconnect the G57, G58, 4A, 4P and 4O ECU connectors.


d.

Measure the voltage of the connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
DCTY (G57-24) - Body ground L - Body ground Driver side door courtesy light switch input Driver side door closed 10 to 14 V
Driver side door open Below 1 V
PCTY (G58-21) - Body ground L - Body ground Front passenger side door courtesy light switch input Front passenger side door closed 10 to 14 V
Front passenger side door open Below 1 V
RCTY (G58-7) - Body ground LG- Body ground Slide door RH courtesy light switch input Slide door RH closed 10 to 14 V
Slide door RH open Below 1 V
LCTY (4A-4) - Body ground BE - Body ground Slide door LH courtesy light switch input Slide door LH closed 10 to 14 V
Slide door LH open Below 1 V
BCYL (G57-19) - Body ground R- Body ground Back door courtesy light switch input Back side door closed 10 to 14 V
Back side door open Below 1 V

If the result is not as specified, the main body ECU may have a malfunction.