Home › Vehicle Interior › DOOR LOCK › SMART ENTRY AND START SYSTEM
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292017 SMART ENTRY AND START SYSTEM J

DOOR LOCK  SMART ENTRY AND START SYSTEM  Front Passenger Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

Neither the entry lock nor unlock functions operate when 1): nothing is output from the door electrical key oscillator (for front passenger side), 2) the smart entry and start system is disabled through customization, or 3) the entire power door lock control system is malfunctioning.

WIRING DIAGRAM

B144908E15
6.229,0.635 6.604,0.813 0.375,0.177 10 false CLG2 6.229,1.427 6.625,1.604 0.396,0.177 10 false CG2B 6.229,2.219 6.604,2.396 0.375,0.177 10 false SEN2 6.229,3.021 6.583,3.198 0.354,0.177 10 false SEL2 0.479,0.625 0.854,0.802 0.375,0.177 10 false ANT2 0.479,1.427 0.854,1.604 0.375,0.177 10 false ANT1 0.469,2.24 0.927,2.417 0.458,0.177 10 false SGT2 0.49,3.021 0.844,3.198 0.354,0.177 10 false TRG- 2.823,0.625 3.125,0.802 0.302,0.177 10 false CLG 0.958,0.781 1.135,0.958 0.177,0.177 10 false 2 1.917,0.781 2.094,0.958 0.177,0.177 10 false 8 1.917,1.542 2.094,1.719 0.177,0.177 10 false 3 0.969,6.51 1.146,6.688 0.177,0.177 10 false 3 5.969,4.958 6.146,5.135 0.177,0.177 10 false 4 1.917,2.375 2.094,2.552 0.177,0.177 10 false 2 1.917,3.146 2.094,3.323 0.177,0.177 10 false 9 3.198,0.781 3.5,0.958 0.302,0.177 10 false 10 5.906,0.781 6.208,0.958 0.302,0.177 10 false 35 5.906,1.552 6.208,1.729 0.302,0.177 10 false 36 5.906,2.365 6.208,2.542 0.302,0.177 10 false 23 0.958,1.552 1.135,1.729 0.177,0.177 10 false 5 3.198,1.552 3.375,1.729 0.177,0.177 10 false 5 5.927,3.167 6.104,3.344 0.177,0.177 10 false 6 0.958,2.385 1.135,2.563 0.177,0.177 10 false 6 3.208,2.385 3.385,2.563 0.177,0.177 10 false 6 3.208,3.167 3.385,3.344 0.177,0.177 10 false 4 0.958,3.135 1.135,3.313 0.177,0.177 10 false 1 3.198,4.167 3.375,4.344 0.177,0.177 10 false 1 3.198,5.167 3.375,5.344 0.177,0.177 10 false 7 2.729,1.427 3.125,1.604 0.396,0.177 10 false CLGB 2.729,2.24 3.125,2.417 0.396,0.177 10 false SENS 2.844,3.021 3.125,3.198 0.281,0.177 10 false SEL 2.156,0.625 2.531,0.802 0.375,0.177 10 false ANT2 2.156,1.427 2.531,1.604 0.375,0.177 10 false ANT1 2.156,2.24 2.458,2.417 0.302,0.177 10 false SGT 2.156,3.021 2.51,3.198 0.354,0.177 10 false TRG- 2.906,4.052 3.094,4.229 0.188,0.177 10 false +B 2.781,5.031 3.104,5.208 0.323,0.177 10 false GND 6.229,4.823 6.677,5 0.448,0.177 10 false TSW2 0.458,6.417 0.854,6.594 0.396,0.177 10 false TRG+ 0.052,6.833 3.073,7.354 3.021,0.521 10 false g1 1.698,5.771 5.177,6.115 3.479,0.344 10 false g2 5.948,6.417 7.125,6.802 1.177,0.385 10 false G29 4.104,3.948 4.625,4.313 0.521,0.365 10 false from Battery 1.688,5.938 5.167,6.281 3.479,0.344 10 false Door Electrical Key Oscillator (for Font Passenger Side) 0.031,7.031 3.042,7.542 3.01,0.51 10 false Door Electrical Key Antenna (for Front Passenger Side Door Outside Handle) 5.958,6.573 7.135,6.958 1.177,0.385 10 false Certification ECU

PROCEDURE

1.TROUBLE AREA CONFIRMATION
a.

Check the front passenger door entry lock and unlock function operation.

Condition Proceed to
Front passenger door entry unlock function operates normally A
Front passenger door entry lock function operates normally B
Front passenger door entry lock and unlock functions do not operate C



C

2.CHECK FOR DTC

A

REFER TO " Front passenger door entry unlock function does not operate " FLOWCHART

B

REFER TO " Front passenger door entry lock function does not operate " FLOWCHART

2.CHECK FOR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

By following the tester screen display, check whether any DTCs are output.

Result:
Result Proceed to
DTC output (for 2AZ-FE) A
DTC output (for 2GR-FE) B
No DTC output C




C

3.CHECK MANUAL DOOR LOCK AND UNLOCK OPERATION

A

B

3.CHECK MANUAL DOOR LOCK AND UNLOCK OPERATION
a.

Check that all the doors lock when the door control switch (for manual operation) is turned to LOCK and all doors unlock when turned to UNLOCK.

OK:

All doors can be locked and unlocked with door control switch.




OK

4.CHECK WIRELESS DOOR LOCK CONTROL OPERATION

NG

4.CHECK WIRELESS DOOR LOCK CONTROL OPERATION
a.

Check that the wireless door lock and unlock functions operate normally.

OK:

Wireless door lock and unlock functions operate normally.




OK

5.OPERATION CHECK (TRANSMITTER LED)

NG

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (w/ SMART ENTRY AND START SYSTEM)

5.OPERATION CHECK (TRANSMITTER LED)
a.

Using the wireless operation, unlock the doors. Wait approximately 3 seconds and bring the key within 70 to 100 cm of the driver door outside handle. Check the key's LED.

Result
LED Condition Proceed to
Not Blinking A
Blinking B



A

6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR ELECTRICAL KEY OSCILLATOR)

B

PERFORM WAVE ENVIRONMENT CHECK (CHANGE VEHICLE LOCATION AND CHECK AGAIN)

6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR ELECTRICAL KEY OSCILLATOR)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the oscillator operates.

Certification ECU:
Item Test Details Diagnostic Note
P-Seat Outside Transmitter Front passenger side door electrical key oscillator ON / OFF -

OK:

When key is brought close to door oscillator that is ON, indicator light on key illuminates.




OK

7.CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)

NG

REPLACE CERTIFICATION ECU

7.CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)
B460031E04
0.083,0.417 0.5,0.667 0.417,0.25 0.25,3.667 0.667,3.917 0.417,0.25 2.271,1.781 2.396,1.427 true 2.813,1.771 2.521,1.427 true 1.958,3.646 2.531,3.646 true 2.438,4.135 1.958,3.781 true 0.094,0.042 1.677,0.313 1.583,0.271 10 false Wire Harness Side: 0.156,0.448 0.635,0.729 0.479,0.281 10 false G29 1.198,0.49 2.781,0.76 1.583,0.271 10 false Certification ECU 1.979,1.781 2.438,2.063 0.458,0.281 10 false CLG2 2.729,1.771 3.188,2.052 0.458,0.281 10 false CG2B 0.823,2.521 2.646,2.948 1.823,0.427 10 false Door Electrical Key Oscillator (for Front Passenger Side) 2.594,3.573 3.052,3.854 0.458,0.281 10 false CLGB 2.5,4.104 2.958,4.385 0.458,0.281 10 false CLG 0.365,3.698 0.823,3.979 0.458,0.281 10 false g2

a.

Disconnect the G29 ECU connector.


b.

Disconnect the g2 oscillator connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G29-35 (CLG2) - g2-10 (CLG) Below 1 Ω
G29-36 (CG2B) - g2-5 (CLGB)
G29-35 (CLG2) or g2-10 (CLG) - Body ground 10 kΩ or higher
G29-36 (CG2B) or g2-5 (CLGB) - Body ground




OK

8.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA)
B460030E02
0.5,1.25 0.833,1.5 0.333,0.25 0.5,3.5 0.833,3.75 0.333,0.25 1.719,1.24 2.396,0.833 true 1.563,1.229 1.021,0.927 true 1.292,1.844 1.708,1.396 true 2.313,1.854 1.854,1.396 true 1.854,3.438 2.448,3.438 true 1.875,3.781 2.51,4.219 true 1.031,4.302 1.635,3.802 true 1.021,3.063 1.615,3.458 true 0.083,0.073 1.49,0.333 1.406,0.26 10 false Wire Harness Side: 0.865,0.281 2.708,0.677 1.844,0.396 10 false Door Electrical Key Oscillator (for Front Passenger Side) 2.448,0.74 2.906,0.99 0.458,0.25 10 false ANT1 0.979,1.854 1.438,2.104 0.458,0.25 10 false ANT2 0.688,0.813 1.146,1.063 0.458,0.25 10 false SGT 2.344,1.833 2.802,2.083 0.458,0.25 10 false TRG- 0.583,1.292 1.042,1.542 0.458,0.25 10 false g2 0.594,3.531 1.052,3.781 0.458,0.25 10 false g1 0.958,2.25 2.74,2.677 1.781,0.427 10 false Door Electrical Key Antenna (for Front Passenger Side) 0.656,2.969 1.115,3.219 0.458,0.25 10 false TRG- 2.51,3.344 2.969,3.594 0.458,0.25 10 false ANT2 0.667,4.25 1.125,4.5 0.458,0.25 10 false ANT1 2.563,4.188 3.021,4.438 0.458,0.25 10 false SGT2

a.

Disconnect the g2 oscillator connector.


b.

Disconnect the g1 antenna connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
g2-2 (SGT) - g1-6 (SGT2) Below 1 Ω
g2-3 (ANT1) - g1-5 (ANT1)
g2-8 (ANT2) - g1-2 (ANT2)
g2-9 (TRG-) - g1-1 (TRG-)
g2-2 (SGT) or g1-6 (SGT2) - Body ground 10 kΩ or higher
g2-3 (ANT1) or g1-5 (ANT1) - Body ground
g2-8 (ANT2) or g1-2 (ANT2) - Body ground
g2-9 (TRG-) or g1-1 (TRG-) - Body ground




OK

9.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)
U188596E02
1.385,1.896 1.115,1.521 false 1.521,2.063 1.396,2.542 false 0.073,0.042 1.49,0.25 1.417,0.208 10 false Wire Harness Side: 0.875,1.375 1.177,1.594 0.302,0.219 10 false +B 1.042,2.49 1.51,2.698 0.469,0.208 10 false GND 0.406,1.781 0.635,2.031 0.229,0.25 10 false g2

a.

Disconnect the g2 oscillator connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
g2-7 (GND) - Body ground Below 1 Ω



c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
g2-1(+B) - Body ground 10 to 14 V




OK

10.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
B460033E02
0.5,1.667 0.917,1.917 0.417,0.25 0.083,3.167 0.5,3.417 0.417,0.25 0.979,1.25 1.563,1.75 true 0.448,4.333 0.74,3.885 true 0.094,0.063 1.531,0.313 1.438,0.25 10 false Wire Harness Side: 0.792,0.438 2.531,0.917 1.74,0.479 10 false Door Electrical Key Antenna (for Front Passenger Side) 0.563,1.135 1.073,1.396 0.51,0.26 10 false TRG+ 0.625,1.698 1.135,1.958 0.51,0.26 10 false g1 0.146,3.208 0.656,3.469 0.51,0.26 10 false G29 1.188,3.156 2.49,3.458 1.302,0.302 10 false Certification ECU 0.146,4.333 0.656,4.594 0.51,0.26 10 false TSW2

a.

Disconnect the g2 oscillator connector.


b.

Disconnect the G29 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
g2-3 (TRG+) - G29-4 (TSW2) Below 1 Ω
g2-3 (TRG+) - G29-4 (TSW2) - Body ground 10 kΩ or higher




OK

11.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)

Temporarily replace the front door outside handle (electrical key antenna) with a new or normally functioning one.

a.

Check that the entry lock and unlock functions operate normally (see page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>OPERATION CHECK).

OK:

Entry lock and unlock functions operate normally.




NG

12.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)

OK

END (ELECTRICAL KEY ANTENNA IS DEFECTIVE)

12.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
a.

Temporarily replace the door electrical key oscillator (for front passenger side) with a new or normally functioning one.


b.

Check that the entry lock and unlock functions operate normally.

OK:

Entry lock and unlock functions operate normally.




NG

13.CHECK MAIN BODY ECU (OPERATION)

OK

END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

13.CHECK MAIN BODY ECU (OPERATION)
a.

Temporarily replace the main body ECU with a new or normally functioning one.


b.

Check that the entry lock and unlock functions operate normally.

OK:

Entry lock and unlock functions operate normally.




OK

END (MAIN BODY ECU IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU