Home › Vehicle Interior › DOOR LOCK › SMART ENTRY AND START SYSTEM
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292017 SMART ENTRY AND START SYSTEM J

DOOR LOCK  SMART ENTRY AND START SYSTEM  Wireless Door Lock Buzzer Does not Sound  


DESCRIPTION

Each of the smart entry and start system warnings use the wireless door lock buzzer to alert the driver. The certification ECU determines whether the wireless door lock buzzer must sound in accordance with the warning conditions.

WIRING DIAGRAM

B144906E03
1.917,1.802 3.823,2.271 1.906,0.469 10 false A19 5.344,2.99 6.583,3.417 1.24,0.427 10 false G29 5.229,1.01 5.448,1.198 0.219,0.188 10 false 21 1.677,1.021 1.813,1.188 0.135,0.167 10 false 2 3.677,1.021 3.833,1.208 0.156,0.188 10 false 1 5.531,0.896 5.917,1.031 0.385,0.135 10 false BZR 1.906,1.969 3.813,2.438 1.906,0.469 10 false Wireless Door Lock Buzzer 5.344,3.156 6.583,3.583 1.24,0.427 10 false Certification ECU

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WIRELESS DOOR LOCK BUZZER)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the wireless door lock buzzer sounds.

Certification ECU:
Item Test Details Diagnostic Note
Wireless Buzzer Operation Wireless door lock buzzer ON / OFF -

OK:

Wireless door lock buzzer sounds.




NG

2.CHECK WIRE HARNESS (CERTIFICATION ECU - WIRELESS DOOR LOCK BUZZER AND BODY GROUND)

OK

REPLACE CERTIFICATION ECU

2.CHECK WIRE HARNESS (CERTIFICATION ECU - WIRELESS DOOR LOCK BUZZER AND BODY GROUND)
B460034E01
0.25,0.5 0.667,0.75 0.417,0.25 0.5,3.583 0.917,3.833 0.417,0.25 0.542,1.802 0.719,1.417 true 0.313,0.531 0.771,0.76 0.458,0.229 10 false G29 0.094,0.052 1.51,0.281 1.417,0.229 10 false Wire Harness Side: 1.115,0.469 2.302,0.719 1.188,0.25 10 false Certification ECU 0.292,1.823 0.75,2.052 0.458,0.229 10 false BZR 0.583,3.615 1.042,3.844 0.458,0.229 10 false A19 0.813,2.625 2.594,2.948 1.781,0.323 10 false Wireless Door Lock Buzzer

a.

Disconnect the G29 ECU connector.


b.

Disconnect the A19 buzzer connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G29-21 (BZR) - A19-1 Below 1 Ω
A19-2 - Body ground
G29-21 (BZR) or A19-1 - Body ground 10 kΩ or higher




OK

3.INSPECT WIRELESS DOOR LOCK BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT WIRELESS DOOR LOCK BUZZER
B127185

a.

Measure the resistance of the buzzer.

Standard resistance:
Tester Connection Specified Condition
1 - 2 Approx. 1 kΩ




OK

REPLACE CERTIFICATION ECU

NG

REPLACE WIRELESS DOOR LOCK BUZZER