Home › Vehicle Interior › ENGINE HOOD / DOOR › BACK DOOR CLOSER SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292018 BACK DOOR CLOSER SYSTEM J

ENGINE HOOD / DOOR  BACK DOOR CLOSER SYSTEM  Back Door Courtesy Switch Circuit  


DESCRIPTION

The back door courtesy switch is built into the back door lock. The switch turns on when the back door is opened and turns off when the door is closed. Back door open/close state signals are input to the power back door ECU.

WIRING DIAGRAM

B144402E28
3.042,0.583 3.365,0.729 0.323,0.146 10 false CTY 3.375,0.573 3.698,0.719 0.323,0.146 10 false 3 5.635,0.448 5.917,0.635 0.281,0.188 10 false FUL 1.802,1.042 4.01,1.375 2.208,0.333 10 false Back Door Lock (Back Door Courtesy Light Switch) 2.448,0.583 2.583,0.771 0.135,0.188 10 false E 2.26,0.583 2.396,0.771 0.135,0.188 10 false 4 5.354,1.313 5.656,1.49 0.302,0.177 10 false M24 5.375,1.5 6.927,1.833 1.552,0.333 10 false Power Back Door Unit (Power Back Door ECU) 5.344,0.583 5.583,0.74 0.24,0.156 10 false 20 1.802,0.833 2.104,0.979 0.302,0.146 10 false S12

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (BACK DOOR COURTESY LIGHT SWITCH)
a.

Check the Data List for proper functioning of the back door courtesy light switch.

Power back door unit (Power back door ECU):
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Courtesy SW Back door courtesy light switch signal / ON or OFF ON: Back door is open
OFF: Back door is closed
-


OK:

The display is as specified in the normal condition.




NG

2.INSPECT BACK DOOR LOCK (BACK DOOR COURTESY LIGHT SWITCH)

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT BACK DOOR LOCK (BACK DOOR COURTESY LIGHT SWITCH)
B143899E26
3.083,2.51 3.75,3.583 3.75,3.583 3.802,3.583 false 5.365,1.927 5.865,2.313 false 4.656,2.25 5.188,1.938 false 4.427,3.958 5.125,4.115 0.698,0.156 10 false Over-latch 4.323,4.281 4.938,4.427 0.615,0.146 10 false Full-latch 4.115,5.229 4.729,5.375 0.615,0.146 10 false Half-latch 3.719,5.854 4.448,6.031 0.729,0.177 10 false Open-latch 3.198,1.771 3.604,2.042 0.406,0.271 10 true Close 2.198,1.729 2.708,1.99 0.51,0.26 10 true Release 3.823,3.531 4.531,3.688 0.708,0.156 10 false Drive Gear 4.542,2.188 4.677,2.344 0.135,0.156 10 false E 5.896,2.271 6.198,2.417 0.302,0.146 10 false CTY

a.

Remove the back door lock.


b.

Measure the resistance of the switch.

Standard resistance:
Tester Connection Condition Specified Condition
3 (CTY) - 4 (E) Open-latch Below 1 Ω
3 (CTY) - 4 (E) Half-latch Below 1 Ω
3 (CTY) - 4 (E) Full-latch 10 kΩ or higher
3 (CTY) - 4 (E) Over-latch 10 kΩ or higher




OK

3.INSPECT WIRE HARNESS (BACK DOOR LOCK - POWER BACK DOOR UNIT AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK

3.INSPECT WIRE HARNESS (BACK DOOR LOCK - POWER BACK DOOR UNIT AND BODY GROUND)
U188668E01
0.054,0.024 1.544,0.171 1.489,0.147 10 Wire Harness Side: 1.126,0.781 2.134,0.936 1.008,0.156 10 Back Door Lock 0.221,1.66 0.534,1.820 0.313,0.161 10 S12 0.825,2.476 2.393,2.820 1.568,0.343 10 Power Back Door Unit (Power Back Door ECU) 0.143,3.734 0.452,3.881 0.309,0.147 10 M24 2.29,1.929 2.756,2.076 0.466,0.147 10 E 0.804,1.896 1.270,2.043 0.466,0.147 10 CTY 1.558,4.404 1.904,4.555 0.346,0.151 10 FUL 1.762,4.366 1.929,4.103 false 1.856,1.921 2.234,2.002 false 1.607,1.916 1.199,1.976 false

a.

Disconnect the S12 door lock connector.


b.

Disconnect the M24 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
S12-3 (CTY) - M24-20 (FUL) Below 1 Ω
S12-4 (E) - Body ground Below 1 Ω
S12-3 (CTY) - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR