Home › Vehicle Interior › ENGINE HOOD / DOOR › BACK DOOR CLOSER SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292018 BACK DOOR CLOSER SYSTEM J

ENGINE HOOD / DOOR  BACK DOOR CLOSER SYSTEM  Back Door Lock Motor Circuit  


DESCRIPTION

The back door lock motor is built into the back door lock. The power back door ECU controls the back door lock motor to open/close the back door. This ECU applies current to terminals DC+ and DC- to operate the motor to close the door. It reverses the direction of the current to operate the motor to open the door.

WIRING DIAGRAM

B144403E02
2.958,0.865 3.281,1.01 0.323,0.146 10 false M+ 3.219,0.885 3.542,1.031 0.323,0.146 10 false 1 5.49,0.792 5.802,0.948 0.313,0.156 10 false DC+ 5.49,2.271 5.802,2.427 0.313,0.156 10 false DC- 1.781,1.406 3.302,1.75 1.521,0.344 10 false Back Door Lock (Back Door Lock Motor) 1.615,0.896 1.854,1.083 0.24,0.188 10 false M- 1.417,0.896 1.583,1.052 0.167,0.156 10 false 2 5.177,2.625 5.479,2.802 0.302,0.177 10 false M24 5.198,2.813 6.75,3.146 1.552,0.333 10 false Power Back Door Unit (Power Back Door ECU) 1.771,1.24 2.073,1.385 0.302,0.146 10 false S12 5.302,2.354 5.625,2.5 0.323,0.146 10 false 1 5.26,0.885 5.427,1.042 0.167,0.156 10 false 2

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BACK DOOR MOTOR)
a.

Select the Active Test, use the intelligent tester to generate a control command, and check that the back door lock motor operates.

Power back door unit (Power back door ECU)
Item Test Details Diagnostic Note
PBD Motor Power back door motor ON / OFF -

OK:

Back door lock motor normal operates.




NG

2.INSPECT BACK DOOR LOCK (BACK DOOR LOCK MOTOR)

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT BACK DOOR LOCK (BACK DOOR LOCK MOTOR)
B143899E23
4.43,3.957 5.123,4.113 0.693,0.156 10 Over-latch 4.322,4.279 4.936,4.426 0.614,0.147 10 Full-latch 4.112,5.227 4.731,5.369 0.619,0.142 10 Half-latch 3.72,5.853 4.450,6.027 0.730,0.174 10 Open-latch 3.201,1.766 3.607,1.918 0.406,0.151 10 Close 2.193,1.734 2.724,1.876 0.531,0.142 10 Release 3.827,3.532 4.539,3.692 0.711,0.161 10 Drive Gear 3.085,2.514 3.752,3.588 3.752,3.588 3.799,3.588 false 5.989,2.163 6.460,2.398 0.471,0.235 10 DC- 4.336,2.173 4.807,2.407 0.471,0.235 10 DC+ 4.476,2.132 5.201,1.749 false 5.366,1.749 6.074,2.131 false

a.

Remove the back door lock.


b.

Apply battery voltage and check operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (DC+)
Battery negative (-) → Terminal 2 (DC-)
Latch turns to open-latch position
Battery positive (+) → Terminal 1 (DC+)
Battery negative (-) → Terminal 2 (DC-)
Latch turns to open-latch position




OK

3.CHECK WIRE HARNESS (BACK DOOR LOCK - POWER BACK DOOR UNIT AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK

3.CHECK WIRE HARNESS (BACK DOOR LOCK - POWER BACK DOOR UNIT AND BODY GROUND)
U188669E02
1.115,1.885 1.615,1.656 false 1.844,1.656 2.167,1.875 false 0.604,4.396 0.76,3.865 false 1,3.865 1.125,4.396 false 0.052,0.021 1.635,0.167 1.583,0.146 10 false Wire Harness Side: 1.104,0.51 2.115,0.667 1.01,0.156 10 false Back Door Lock 0.292,1.76 0.604,1.917 0.313,0.156 10 false S12 0.823,2.469 2.344,2.802 1.521,0.333 10 false Power Back Door Unit (Power Back Door ECU) 0.167,3.771 0.479,3.917 0.313,0.146 10 false M24 2.198,1.792 2.667,1.938 0.469,0.146 10 false M- 0.823,1.813 1.292,1.958 0.469,0.146 10 false M+ 0.479,4.406 0.823,4.552 0.344,0.146 10 false DC- 1,4.396 1.344,4.542 0.344,0.146 10 false DC+

a.

Disconnect the S12 door lock connector.


b.

Disconnect the M24 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
S12-1 (M+) - M24-2 (DC+) Below 1 Ω
S12-2 (M-) - M24-1 (DC-) Below 1 Ω
S12-1 (M+) - Body ground 10 kΩ or higher
S12-2 (M-) - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR