Home › Vehicle Interior › ENGINE HOOD / DOOR › BACK DOOR CLOSER SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292018 BACK DOOR CLOSER SYSTEM C

ENGINE HOOD / DOOR  BACK DOOR CLOSER SYSTEM  B2250  Back Door Closer Operation Malfunction  


DESCRIPTION

The power back door unit (power back door ECU) inputs signals from the full-latch switch, selector switch and back door courtesy light switch, which are built into the back door lock. Based on these switch signals, the latch position of the back door lock is determined.

DTC No. DTC Detection Condition Trouble Area
B2250 While back door closer is operating, malfunction is detected in position information from each switch within specified amount of time
·

Back door lock

·

Wire harness

·

Power back door unit (Power back door ECU)



WIRING DIAGRAM

B464097E01
1.26,0.885 2.5,1.25 1.24,0.365 10 false Back Door Courtesy Light Switch 1.26,2.094 2.281,2.365 1.021,0.271 10 false Selector Switch 1.177,3.281 2.271,3.5 1.094,0.219 10 false Full-latch Switch 1.042,3.969 2.208,4.188 1.167,0.219 10 false Back Door Lock 1.042,3.792 1.5,3.99 0.458,0.198 10 false S12 0.469,3.177 0.625,3.375 0.156,0.198 10 false 4 0.708,2.906 0.865,3.104 0.156,0.198 10 false E 2.365,0.531 2.823,0.729 0.458,0.198 10 false CTY 2.792,0.771 2.948,0.969 0.156,0.198 10 false 3 2.25,1.729 2.865,1.927 0.615,0.198 10 false DLSW 2.781,1.958 2.938,2.156 0.156,0.198 10 false 6 2.219,2.938 2.833,3.135 0.615,0.198 10 false ULSW 2.792,3.167 2.948,3.365 0.156,0.198 10 false 5 5.49,0.646 5.948,0.844 0.458,0.198 10 false FUL 5.198,0.771 5.51,0.969 0.313,0.198 10 false 20 5.49,1.854 5.948,2.052 0.458,0.198 10 false POS 5.177,1.969 5.49,2.167 0.313,0.198 10 false 24 5.469,3.052 5.927,3.25 0.458,0.198 10 false HAF 5.167,3.167 5.479,3.365 0.313,0.198 10 false 22 5.396,3.5 5.854,3.698 0.458,0.198 10 false M24 5.406,3.688 6.948,4.094 1.542,0.406 10 false Power Back Door Unit (Power Back Door ECU)

PROCEDURE

1.INSPECT BACK DOOR LOCK (FULL-LATCH SWITCH, SELECTOR SWITCH AND COURTESY SWITCH)
B143899E22
3.083,2.51 3.75,3.583 3.75,3.583 3.802,3.583 false 4.958,2.646 5.188,2.125 false 5.365,2.104 5.531,2.667 false 5.365,1.927 5.865,2.313 false 4.656,2.25 5.188,1.938 false 4.427,3.958 5.125,4.115 0.698,0.156 10 false Over-latch 4.323,4.281 4.938,4.427 0.615,0.146 10 false Full-latch 4.115,5.229 4.729,5.375 0.615,0.146 10 false Half-latch 3.719,5.854 4.448,6.031 0.729,0.177 10 false Open-latch 3.198,1.771 3.604,1.917 0.406,0.146 10 false Close 2.198,1.729 2.729,1.875 0.531,0.146 10 false Release 3.823,3.531 4.531,3.688 0.708,0.156 10 false Drive Gear 5.344,2.667 5.813,2.885 0.469,0.219 10 false ULSW 4.542,2.188 4.677,2.344 0.135,0.156 10 false E 5.906,2.271 6.208,2.51 0.302,0.24 10 false CTY 4.708,2.667 5.167,2.865 0.458,0.198 10 false DLSW

a.

Remove the back door lock.


b.

Measure the resistance of the switch.

Standard resistance :
Full-latch switch
Tester Connection Door Lock Latch Position Specified Condition
5 (ULSW) - 4 (E) Over-latch Below 1 Ω
5 (ULSW) - 4 (E) Open-latch 10 kΩ or higher
5 (ULSW) - 4 (E) Full-latch 10 kΩ or higher
5 (ULSW) - 4 (E) Half-latch 10 kΩ or higher


Selector switch:
Tester Connection Door Lock Latch Position Specified Condition
6 (DLSW) - 4 (E) Open-latch Below 1 Ω
6 (DLSW) - 4 (E) Over-latch 10 kΩ or higher
6 (DLSW) - 4 (E) Full-latch 10 kΩ or higher
6 (DLSW) - 4 (E) Half-latch 10 kΩ or higher


Back door courtesy light switch:
Tester Connection Door Lock Latch Position Specified Condition
3 (CTY) - 4 (E) Open-latch Below 1 Ω
3 (CTY) - 4 (E) Half-latch Below 1 Ω
3 (CTY) - 4 (E) Full-latch 10 kΩ or higher
3 (CTY) - 4 (E) Over-latch 10 kΩ or higher




OK

2.CHECK WIRE HARNESS (BACK DOOR LOCK - POWER BACK DOOR UNIT AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK

2.CHECK WIRE HARNESS (BACK DOOR LOCK - POWER BACK DOOR UNIT AND BODY GROUND)
U188667E02
1.99,4.365 2.135,4.094 false 2.375,4.083 2.49,4.375 false 1.896,4.083 1.365,4.396 false 1.167,2.25 1.552,2.167 false 1.906,2.156 2.24,2.229 false 1.854,1.917 2.229,2 false 1.604,1.917 1.198,1.979 false 0.052,0.021 1.542,0.167 1.49,0.146 10 false Wire Harness Side: 1.125,0.781 2.135,0.938 1.01,0.156 10 false Back Door Lock 0.24,1.667 0.552,1.823 0.313,0.156 10 false S12 0.823,2.479 2.396,2.823 1.573,0.344 10 false Power Back Door Unit (Power Back Door ECU) 0.167,3.729 0.479,3.875 0.313,0.146 10 false M24 2.292,1.927 2.76,2.073 0.469,0.146 10 false E 0.625,2.167 1.094,2.313 0.469,0.146 10 false ULSW 0.802,1.896 1.271,2.042 0.469,0.146 10 false CTY 2.26,2.167 2.729,2.313 0.469,0.146 10 false DLSW 1.792,4.406 2.135,4.552 0.344,0.146 10 false HAF 1.177,4.406 1.521,4.552 0.344,0.146 10 false FUL 2.313,4.396 2.656,4.542 0.344,0.146 10 false POS

a.

Disconnect the S12 door lock connector.


b.

Disconnect the M24 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
S12-5 (ULSW) - M24-22 (HAF) Below 1 Ω
S12-6 (DLSW) - M24-24 (POS) Below 1 Ω
S12-3 (CTY) - M24-20 (FUL) Below 1 Ω
S12-4 (E) - Body ground Below 1 Ω
S12-5 (ULSW) - Body ground 10 kΩ or higher
S12-6 (DLSW) - Body ground 10 kΩ or higher
S12-3 (CTY) - Body ground 10 kΩ or higher




OK

REPLACE POWER BACK DOOR UNIT (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR