Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292019 POWER SLIDE DOOR SYSTEM J

ENGINE HOOD / DOOR  POWER SLIDE DOOR SYSTEM  Main Switch Circuit  


DESCRIPTION

Turning the power slide door main switch off (pushed in) prohibits power slide door control system operation.

The door control relay (ECU) senses that the fuel lid is open via the fuel lid courtesy switch. When the power slide door motor is opening, if the fuel lid is open, the slide door will not open fully.

WIRING DIAGRAM

B144072E14
5.26,1.198 7.094,1.594 1.833,0.396 10 false Door Control Relay LH (Power Slide Door ECU LH) 5.25,2.927 7.115,3.292 1.865,0.365 10 false Door Control Relay RH (Power Slide Door ECU RH) 5.448,0.594 5.917,0.74 0.469,0.146 10 false MSW 5.177,0.51 5.323,0.656 0.146,0.146 10 false 8 2.385,2.24 2.531,2.385 0.146,0.146 10 false 9 0.427,2.24 0.573,2.385 0.146,0.146 10 false 6 5.167,2.24 5.375,2.385 0.208,0.146 10 false 11 5.5,2.333 5.969,2.479 0.469,0.146 10 false MSW 0.573,2.781 0.906,2.927 0.333,0.146 10 false G44 5.25,2.771 5.583,2.917 0.333,0.146 10 false N24 5.26,1.031 5.594,1.177 0.333,0.146 10 false M22 0.573,2.927 2.531,3.146 1.958,0.219 10 false Power Slide Door Main Switch 4.667,0.49 4.813,0.635 0.146,0.146 10 false 1 2.708,0.49 2.854,0.635 0.146,0.146 10 false 2 2.917,1.042 3.25,1.188 0.333,0.146 10 false M23 2.917,1.198 5.063,1.615 2.146,0.417 10 false Slide Door Half Open Stopper Control (Fuel Lid Courtesy Switch) 2.427,1.167 2.625,1.313 0.198,0.146 10 false *1 4.01,2.219 4.208,2.365 0.198,0.146 10 false *2 0.469,1.115 2.208,1.25 1.74,0.135 10 false *1: w/ Power Slide Door LH 0.469,1.531 2.208,1.667 1.74,0.135 10 false *2: w/ Power Slide Door RH

PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.

Result:
Result Proceed to
Models with Power Slide Door LH only or Power Slide Door both LH and RH A
Models with Power Slide Door RH only B




A

2.READ VALUE USING INTELLIGENT TESTER

B

3.READ VALUE USING INTELLIGENT TESTER
2.READ VALUE USING INTELLIGENT TESTER
a.

Use the Data List to check if the door lock is functioning properly.

Door control relay LH (Power slide door ECU LH)
Item Measurement Item / Display (Range) Normal Condition Diagnosis Note
PSD Main Switch Power slide door main switch signal / ON or OFF ON: Power slide door main switch is pressed
OFF: Power slide door main switch is not pressed
-
Fuel Lid SW Fuel lid courtesy switch signal / ON or OFF ON: Fuel lid is closed
OFF: Fuel lid is open
-

OK:

When the main switch and fuel lid switch are operating, the intelligent tester should display as shown in the table.


Result:
Result Proceed to
OK (w/ Power Slide Door RH) A
OK (w/o Power Slide Door RH) B
NG C




A

3.READ VALUE USING INTELLIGENT TESTER

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

6.INSPECT POWER SLIDE DOOR MAIN SWITCH
3.READ VALUE USING INTELLIGENT TESTER
a.

Use the Data List to check if the door lock is functioning properly.

Door control relay RH (Power slide door ECU RH)
Item Measurement Item / Display (Range) Normal Condition Diagnosis Note
PSD Main Switch Power slide door main switch signal / ON or OFF ON: Power slide door main switch is pressed
OFF: Power slide door main switch is not pressed
-

OK:

When the main switch is operating, the intelligent tester should display as shown in the table.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.INSPECT POWER SLIDE DOOR MAIN SWITCH
4.INSPECT POWER SLIDE DOOR MAIN SWITCH
a.
U185961E02
1.292,2.729 1.906,2.927 0.615,0.198 10 false Pushed 0.135,2.083 0.667,2.281 0.531,0.198 10 false Pushed 0.229,3.229 0.531,3.417 0.302,0.188 10 false OFF

Remove the power slide door main switch.


b.

Measure the resistance of the power slide door main switch.

Standard resistance:
Tester Connection Condition Specified Condition
9 - 6 Pushed Below 1 Ω
9 - 6 OFF 10 kΩ or higher




OK

5.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)

NG

REPLACE POWER SLIDE DOOR MAIN SWITCH

5.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)
U188886E02
1.979,3.906 2.281,4.302 false 0.073,0.021 1.385,0.177 1.313,0.156 10 false Wire Harness Side: 0.5,0.521 2.396,0.667 1.896,0.146 10 false Power Slide Door Main Switch 0.677,2.75 2.365,2.896 1.688,0.146 10 false Power Slide Door ECU RH 2.073,4.333 2.469,4.5 0.396,0.167 10 false MSW 0.594,1.583 0.906,1.729 0.313,0.146 10 false G44 0.563,3.677 0.844,3.823 0.281,0.146 10 false N24

a.

Disconnect the G44 power slide door main switch connector.


b.

Disconnect the N24 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G44-9 - N24-11 (MSW) Below 1 Ω
G44-9 - Body ground 10 kΩ or higher
G44-6 - Body ground Below 1 Ω




OK

REPLACE POWER SLIDE DOOR ECU RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER SLIDE DOOR MAIN SWITCH
a.
U185961E02
1.292,2.729 1.906,2.927 0.615,0.198 10 false Pushed 0.135,2.083 0.667,2.281 0.531,0.198 10 false Pushed 0.229,3.229 0.531,3.417 0.302,0.188 10 false OFF

Remove the power slide door main switch.


b.

Measure the resistance of the power slide door main switch.

Standard resistance:
Tester Connection Condition Specified Condition
9 - 6 Pushed Below 1 Ω
9 - 6 OFF 10 kΩ or higher




OK

7.INSPECT FUEL LID COURTESY SWITCH

NG

REPLACE POWER SLIDE DOOR MAIN SWITCH

7.INSPECT FUEL LID COURTESY SWITCH
a.
B138846E01
0.228,0.949 1.096,1.112 0.868,0.163 10 Fuel lid open 0.228,2.75 1.264,2.913 1.036,0.163 10 Fuel lid closed

Remove the fuel lid courtesy switch.


b.

Measure the resistance of the fuel lid courtesy switch connector.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 OFF (Fuel lid open) 10 kΩ or higher
1 - 2 ON (Fuel lid closed) Below 1 Ω




OK

8.CHECK WIRE HARNESS

NG

REPLACE FUEL LID COURTESY SWITCH

8.CHECK WIRE HARNESS
U188685E02
5.396,1.458 5.729,1.229 false 0.135,0.104 1.49,0.281 1.354,0.177 10 false Wire Harness Side: 2.781,0.406 4.375,0.604 1.594,0.198 10 false Fuel Lid Courtesy Switch 5.083,0.417 6.781,0.573 1.698,0.156 10 false Power Slide Door ECU LH 2.656,0.854 2.969,1.021 0.313,0.167 10 false M23 4.906,0.792 5.219,0.958 0.313,0.167 10 false M22 5,1.417 5.406,1.563 0.406,0.146 10 false MSW 0.198,0.406 2.188,0.604 1.99,0.198 10 false Power Slide Door Main Switch 0.354,0.917 0.667,1.083 0.313,0.167 10 false G44

a.

Disconnect the G44 switch connector.


b.

Disconnect the M23 switch connector.


c.

Disconnect the M22 ECU connector.


d.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
M23-1 - M22-8 (MSW) Below 1 Ω
G44-9 - M23-2 Below 1 Ω
G44-6 - Body ground Below 1 Ω
G44-9 - Body ground 10 kΩ or higher
M23-1 - Body ground 10 kΩ or higher




OK

REPLACE POWER SLIDE DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR