Inspection should be started after conforming that the items listed in the "CUSTOMIZE PARAMETERS" for the power slide door system have defaulted to the initial settings (see page Vehicle Interior>ENGINE HOOD / DOOR>POWER SLIDE DOOR SYSTEM>CUSTOMIZE PARAMETERS).
CHECK OPENING OPERATION
Conditions necessary for the power slide door to open:
Power slide door main switch is in the ON position.
Slide door is positioned between the fully closed position and the half-open position (When the slide door is fully closed, the door must be unlocked).
Shift lever is in the P position when the ignition switch is ON (When the ignition switch is OFF, power slide door can operate in any position of the shift lever).
No key is inserted into the ignition key cylinder when the transmitter is used.
Fuel lid is closed.
Press the power slide door control switch.
Check that the power slide door opens when the switch has been pressed for more than 0.5 seconds.
The power slide door can operate even when the child lock is ON.
Check that the power slide door reverses operation and moves to the fully closed position when the same switch is pressed again during opening.
Press the transmitter switch for the power slide door.
Check that the power slide door opens when the switch has been pressed for more than 0.9 seconds.
The power slide door can operate even when the child lock is ON.
Check that the power slide door reverses operation and moves to the fully closed position when the same switch is pressed again during opening.
Pull the outside / inside handle for the power slide door.
Check that the power slide door opens when the handle is pulled.
For the inside handle, the power slide door can operate only when the child lock is OFF.
For the outside handle, the power slide door can operate even when the child lock is ON.
Check that the power slide door reverses operation and moves to the fully closed position when the same handle is pulled again during opening.
CHECK CLOSING OPERATION
Conditions necessary for the power slide door to close:
Power slide door main switch is in the ON position.
Slide door is positioned between the fully open position and the half-open position.
No key is inserted into the ignition key cylinder when the transmitter is used.
Press the power slide door control switch.
Check that the power slide door closes when the switch has been pressed for more than 0.5 seconds.
The power slide door can operate even when the child lock is ON.
Check that the power slide door reverses operation and moves to the fully open position when the same switch is pressed again during closing.
Press the transmitter switch for the power slide door.
Check that the power slide door closes when the switch has been pressed for more than 0.9 seconds.
The power slide door can operate even when the child lock is ON.
Check that the power slide door reverses operation and moves to the fully open position when the same switch is pressed again during closing.
Pull the outside / inside handle for the power slide door.
Check that the power slide door closes when the handle is pulled.
Check that the power slide door reverses operation and moves to the fully open position when the same handle is pulled again during closing.
CHECK JAM PROTECTION FUNCTION
Do not use any part of the body to check this function. Make sure that nothing becomes accidentally caught in the power slide door during operation.
The power slide door motor and power slide door clutch detect changes in the operating speed of the slide door while the power slide door is moving. If a change in the operating speed is out of the normal range, it will be judged to be a jam or foreign objects detection in the direction that the power slide door is moving.
When the power slide door touch sensor built into the front end of the slide door is compressed, it will be judged to be a jam or foreign objects detection in the direction that the power slide door is moving, and the power slide door movement will reverse.
The power slide door touch sensor operates only while the slide door is closing. It does not operate while the slide door is opening.
Check the jam protection function while the power slide door is closing.
Fully open the slide door.
Press the switch that operates the power side door to close it.
While the slide door is closing, press the touch sensor using the handle of a hammer or the equivalent.
Check that the jam protection function is immediately activated and the power slide door reverses operation to the fully open position.
Check the jam protection function while the power slide door is opening.
Fully close the slide door.
Press the switch that operates the power side door to open it.
While the slide door is opening, hold the slide door using a tire or the equivalent so that the operating speed decreases.
Check that the jam protection function is immediately activated and the power slide door reverses operation to the fully closed position.
Check the operation of the power slide door when the jam protection function is consecutively activated.
Check that the power slide door operation is cancelled and switched to the manual operation mode (not electrically controlled) when the jam protection function has been activated 2 or more consecutive times.
Refer to the previous 2 steps for methods to activate the jam protection function.
To restore the power slide door system to the normal operation mode, perform either of the following: manually close the slide door fully or press the transmitter switch for the power slide door or the power slide door control switch again.
CHECK FUEL LID STOPPER SYSTEM (w/ Power Slide Door LH)
The fuel lid stopper system operates against the slide door LH only, because the fuel lid is placed on the LH side of the vehicle.
To prevent the slide door striking against an open fuel lid, the slide door half stop control pulls the cable to operate the open stopper.
The fuel lid courtesy switch built into the slide door half stop control detects that the fuel lid is open.
Check that the slide door cannot be opened when the fuel lid is open.
Check that the power slide door is switched to the manual operation mode when the fuel lid is opened while the power slide door is moving.
To restore the power slide door system to the normal operation mode, perform the following: manually close the slide door fully or press the transmitter switch for the power slide door or the power slide door control switch again.
CHECK SLIDE DOOR HALF-OPEN STOPPER SYSTEM
Operationally linked to the rear power window regulator, the control lever and bellcrank operate and pull the cable, which then operates the half open stopper so that the slide door stops. This prevents the slide door from opening fully.
Check that the slide door is forced to stop by half stopper when the window is open 100 - 150 mm (3.94 - 5.91 in.) or more.