Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292019 POWER SLIDE DOOR SYSTEM C

ENGINE HOOD / DOOR  POWER SLIDE DOOR SYSTEM  B2223  Power Slide Door Pulse Sensor Malfunction on Rear Right Door  


DESCRIPTION

·

A pulse sensor is built into the slide door RH for jam and foreign object detection and for slide door position detection. The jam and foreign object detection feature of the pulse sensor monitors the operating speed of the slide door while the power slide door is in operation. The slide door position detection feature of the pulse sensor monitors where the slide door is. If the slide door position detection feature outputs a pulse signal that is out of the normal range, the power slide door ECU RH will set DTC B2223.

·

If DTC B2223 is set, the power slide door system will be turned off. Thus, the slide door can be moved freely and will be switched to manual operation mode (not electrically controlled).

·

In order to restore the power slide door system to normal operation mode, first solve the problem indicated by DTC B2223 and then manually close the slide door fully (reset operation).


DTC No. DTC Detection Condition Trouble Area
B2223 A pulse sensor which is built in the slide door motor unit RH is malfunction.
·

ECU-B fuse

·

Slide door lock release motor RH

·

Slide door motor unit RH

·

Wire harness or connector



WIRING DIAGRAM

B291827E01
1.576,2.458 3.797,2.623 2.221,0.165 10 Slide Door Lock Release Motor RH 1.576,2.308 1.778,2.473 0.202,0.165 10 K8 4.411,2.691 6.354,3.037 1.943,0.346 10 Door Control Relay RH (Power Slide Door ECU RH) 4.565,1.944 4.767,2.109 0.202,0.165 10 K6 2.905,1.836 3.223,2.002 0.318,0.165 10 SD+ 3.274,1.836 3.390,2.002 0.117,0.165 10 1 2.048,1.836 2.164,2.002 0.117,0.165 10 2 2.237,1.836 2.555,2.002 0.318,0.165 10 SD- 4.518,0.898 4.809,1.063 0.290,0.165 10 N24 4.626,0.688 4.810,0.853 0.184,0.165 10 7 4.635,1.748 4.782,1.913 0.147,0.165 10 9 4.943,1.949 5.368,2.114 0.424,0.165 10 RACT 4.943,0.898 5.368,1.063 0.424,0.165 10 ECUB 3.43,1.033 3.901,1.198 0.471,0.165 10 ECU-B 1.67,0.879 2.483,1.044 0.813,0.165 10 from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK WIRE HARNESS (ECU AND BATTERY AND BODY GROUND)
a.
U185972E03
1.219,1.458 0.875,1.521 false 0.052,0.052 1.385,0.25 1.333,0.198 10 false Wire Harness Side: 0.333,0.792 0.656,0.969 0.323,0.177 10 false N24 0.458,1.458 0.938,1.667 0.479,0.208 10 false ECUB

Disconnect the N24 ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
N24-7 (ECUB) - Body ground 10 to 14 V




OK

2.INSPECT SLIDE DOOR LOCK RELEASE MOTOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT SLIDE DOOR LOCK RELEASE MOTOR RH
a.
B138848E02
2.095,2.228 3.191,2.416 1.096,0.188 10 26.0 to 30.3 mm

Remove the slide door lock release motor.


b.

Apply the battery voltage to the motor terminals and check the operation of the door lock release motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (SD+)
Battery negative (-) → 2 (SD-)
Lock release


Standard stroke:

26.0 to 30.3 mm (1.02 to 1.19 in.)




OK

3.CHECK WIRE HARNESS (RELEASE MOTOR - ECU AND BODY GROUND)

NG

REPLACE SLIDE DOOR LOCK RELEASE MOTOR RH

3.CHECK WIRE HARNESS (RELEASE MOTOR - ECU AND BODY GROUND)
a.
U188900E02
1.344,3.854 0.969,4.208 false 1.906,1.823 2.333,1.615 false 1.125,2.01 1.552,1.802 false 0.083,0.083 1.479,0.25 1.396,0.167 10 false Wire Harness Side: 0.385,0.635 2.594,0.792 2.208,0.156 10 false Slide Door Lock Release Motor RH 0.667,2.552 2.427,2.708 1.76,0.156 10 false Power Slide Door ECU RH 0.792,1.385 0.99,1.573 0.198,0.188 10 false K8 0.563,3.26 0.854,3.448 0.292,0.188 10 false K6 0.781,2.031 1.104,2.188 0.323,0.156 10 false SD- 2.365,1.51 2.688,1.667 0.323,0.156 10 false SD+ 0.729,4.25 1.125,4.406 0.396,0.156 10 false RACT

Disconnect the K8 release motor connector.


b.

Disconnect the K6 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
K8-1 (SD+) - K6-9 (RACT) Below 1 Ω
K8-2 (SD-) - Body ground Below 1 Ω
K8-1 (SD+) - Body ground 10 kΩ or higher




OK

REPLACE SLIDE DOOR MOTOR UNIT RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR