Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292019 POWER SLIDE DOOR SYSTEM C

ENGINE HOOD / DOOR  POWER SLIDE DOOR SYSTEM  B2224  Power Slide Door Pulse Sensor Malfunction on Rear Left Door  


DESCRIPTION

·

A pulse sensor is built into the slide door LH for jam and foreign object detection and for slide door position detection. The jam and foreign object detection feature of the pulse sensor monitors the operating speed of the slide door while the power slide door is in operation. The slide door position detection feature of the pulse sensor monitors where the slide door is. If the slide door position detection feature outputs a pulse signal that is out of the normal range, the power slide door ECU LH will set DTC B2224.

·

If DTC B2224 is set, the power slide door system will be turned off. Thus, the slide door can be moved freely and will be switched to manual operation mode (not electrically controlled).

·

In order to restore the power slide door system to normal operation mode, first solve the problem indicated by DTC B2224 and then manually close the slide door fully (reset operation).


DTC No. DTC Detection Condition Trouble Area
B2224 A pulse sensor which is built in the slide door motor unit LH is malfunction.
·

ECU-B fuse

·

Slide door lock release motor LH

·

Slide door motor unit LH

·

Wire harness or connector



WIRING DIAGRAM

B291827E02
1.576,2.458 3.797,2.623 2.221,0.165 10 Slide Door Lock Release Motor LH 1.576,2.308 1.778,2.473 0.202,0.165 10 L8 4.411,2.691 6.354,3.037 1.943,0.346 10 Door Control Relay LH (Power Slide Door ECU LH) 4.565,1.944 4.767,2.109 0.202,0.165 10 L6 2.905,1.836 3.223,2.002 0.318,0.165 10 SD+ 3.274,1.836 3.390,2.002 0.117,0.165 10 2 2.048,1.836 2.164,2.002 0.117,0.165 10 1 2.237,1.836 2.555,2.002 0.318,0.165 10 SD- 4.518,0.898 4.809,1.063 0.290,0.165 10 M22 4.574,0.688 4.767,0.853 0.193,0.165 10 12 4.583,1.748 4.778,1.913 0.195,0.165 10 13 4.943,1.949 5.368,2.114 0.424,0.165 10 RACT 4.943,0.898 5.368,1.063 0.424,0.165 10 ECUB 3.43,1.033 3.901,1.198 0.471,0.165 10 ECU-B 1.67,0.879 2.483,1.044 0.813,0.165 10 from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK WIRE HARNESS (ECU AND BATTERY AND BODY GROUND)
a.
U185973E03
2.208,1.479 2.563,1.719 false 0.052,0.063 1.385,0.26 1.333,0.198 10 false Wire Harness Side: 0.313,0.771 0.635,0.948 0.323,0.177 10 false M22 2.615,1.656 3.094,1.865 0.479,0.208 10 false ECUB

Disconnect the M22 ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
M22-12 (ECUB) - Body ground 10 to 14 V




OK

2.INSPECT SLIDE DOOR LOCK RELEASE MOTOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT SLIDE DOOR LOCK RELEASE MOTOR LH
a.
B138849E01
0.054,2.345 1.119,2.501 1.065,0.156 10 26.0 to 30.3 mm

Remove the slide door lock release motor.


b.

Apply the battery voltage to the motor terminals and check the operation of the door lock release motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (SD+)
Battery negative (-) → 1 (SD-)
Lock release


Standard stroke:

26.0 to 30.3 mm (1.02 to 1.19 in.)




OK

3.CHECK WIRE HARNESS (RELEASE MOTOR - ECU AND BODY GROUND)

NG

REPLACE SLIDE DOOR LOCK RELEASE MOTOR LH

3.CHECK WIRE HARNESS (RELEASE MOTOR - ECU AND BODY GROUND)
a.
U188901E01
0.083,0.084 1.475,0.254 1.392,0.170 10 Wire Harness Side: 0.39,0.632 2.595,0.788 2.204,0.156 10 Slide Door Lock Release Motor LH 0.714,2.557 2.391,2.713 1.677,0.156 10 Power Slide Door ECU LH 0.789,1.366 0.990,1.550 0.201,0.184 10 L8 0.566,3.261 0.853,3.444 0.287,0.184 10 L6 0.779,2.029 1.105,2.190 0.326,0.161 10 SD+ 2.368,1.509 2.694,1.670 0.326,0.161 10 SD- 2.69,4.137 3.086,4.298 0.396,0.161 10 RACT 2.158,3.863 2.679,4.101 false 1.911,1.824 2.335,1.612 false 1.127,2.009 1.551,1.797 false

Disconnect the L8 slide door lock release motor connector.


b.

Disconnect the L6 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
L8-2 (SD+) - L6-13 (RACT) Below 1 Ω
L8-1 (SD-) - Body ground Below 1 Ω
L8-2 (SD+) - Body ground 10 kΩ or higher




OK

REPLACE SLIDE DOOR MOTOR UNIT LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR