Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292019 POWER SLIDE DOOR SYSTEM J

ENGINE HOOD / DOOR  POWER SLIDE DOOR SYSTEM  Door Control Switch Circuit  


DESCRIPTION

When the main body ECU senses the ON signal from the power slide door control switch on instrument panel, it operates the power slide door motor to "OPEN" or "CLOSE".

WIRING DIAGRAM

B138813E17
1.448,1.792 3.719,1.979 2.271,0.188 10 false Power Slide Door Control Switch LH 4.865,2.229 5.969,2.417 1.104,0.188 10 false Main Body ECU 4.958,1.208 5.417,1.385 0.458,0.177 10 false RLSD 4.865,2.073 5.177,2.25 0.313,0.177 10 false G60 1.458,1.625 1.771,1.802 0.313,0.177 10 false G45 4.708,1.094 4.844,1.271 0.135,0.177 10 false 8 3.365,1.094 3.5,1.271 0.135,0.177 10 false 9 1.438,1.094 1.573,1.271 0.135,0.177 10 false 6 0.063,0 1.146,0.198 1.083,0.198 10 false for RHD only:

PROCEDURE

1.INSPECT POWER SLIDE DOOR CONTROL SWITCH (for LH)
a.
B142339E01
0.059,2.042 0.576,2.216 0.517,0.174 10 Pushed 1.044,2.589 1.561,2.764 0.517,0.174 10 Pushed 0.07,3.125 0.393,3.309 0.323,0.184 10 OFF

Remove the power slide door control switch connector on instrument panel.


b.

Measure the resistance of the power slide door control switch.

Standard resistance:
Tester Connection Condition Specified Condition
9 - 6 Pushed Below 1 Ω
9 - 6 OFF 10 kΩ or higher




OK

2.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)

NG

REPLACE POWER SLIDE DOOR CONTROL SWITCH (for LH)

2.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)
a.
U188690E02
1.635,4.083 1.396,4.396 false 0.188,0.146 1.615,0.333 1.427,0.188 10 false Wire Harness Side: 0.615,0.781 2.875,0.958 2.26,0.177 10 false Power Slide Door Control Switch LH 1.198,2.823 2.24,2.979 1.042,0.156 10 false Main Body ECU 0.667,1.396 0.969,1.594 0.302,0.198 10 false G45 0.688,3.406 0.99,3.604 0.302,0.198 10 false G60 1.021,4.365 1.406,4.542 0.385,0.177 10 false RLSD

Disconnect the G45 power slide door control switch connector.


b.

Disconnect the G60 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G45-9 - G60-8 (RLSD) Below 1 Ω
G45-6 - Body ground Below 1 Ω
G45-9 - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR